Hobbywing Xerun V10 G3-6.5T OnRoad Spec Handleiding

Hobbywing Radiografisch bestuurbaar speelgoed Xerun V10 G3-6.5T OnRoad Spec

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobbywing Xerun V10 G3-6.5T OnRoad Spec (2 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

FEATURES

• It’s a motor specially designed for high-level racing. The RMP of G3 Stock motor is significantly improved, the KV & torque are improved by 16% and 4% respectively, compared with the V10 G2 Stock motor.

• Lightweight. The G3 Modified & Stock motors only weigh 161g & 132g respectively, the weights are reduced by 11% & 21% when comparing with the V10 G2 motors.

• The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor.

• The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G3 Stock motors (10.5T~25.5T), the timing is

adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees.

• The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts.

• The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors

effectively keep sand or dirt from getting inside and damaging the motor(s).

• The use of high-performance stator core, heat(200 )-resistant wire, heat(200 )-resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current ℃ ℃

endurance guarantees outstanding performance and super durability.

INSTALLATION & CONNECTION

• The three output wires (on the ESC) need to be soldered onto the motor, the wires are

differentiated by colors. In general, Blue/Yellow/Orange represents phase A/B/C respectively.

Please note the following points when mounting or connecting the motor.

• The M3 screws with the length (not longer than 8mm) are needed when mounting the

motor onto your vehicle.

• Please pay attention to the relevant marks (on the ESC) when soldering/connecting those

output wires to the motor and make sure that you will strictly follow the wiring order

(between the ESC & the motor) of “A-A, B-B, and C-C”.

• Please ensure the sensor cable is clean and undamaged when you’re using a sensored ESC.

You need to pay attention to the two connectors on the cable when connecting the ESC to

the motor.

• Re-check all the connections between the ESC & the motor and ensure that they are all

correct (as shown in the diagram) before tur ning on the ESC.

Sensor wire Blue power wire (motor phase “A”)

Yellow power wire (motor phase “B”)

Orange power wire (motor phase “C”)

Switch

ESC

Input TH

Channel

(Ch.2)

Receiver

Servo

Battery Positive (Red)Battery Negative (Black)

- + S

CAUTIONS

CAUT I ONS

AT T ENT ION

USER MANUAL

V10 G3

TIMING ADJUSTMENT

The V10 G3 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing.

• You can adjust the motor timing after unfastening the screw on the rear end plate. Please adjust the timing as needed according to the mark (/white lines)

at the rear end of the motor and fasten the screw after the adjustment.

For obtaining the optimal performance, you can change the output range and characteristic of your power system through adjusting the motor timing.

For the (10.5T~25.5T) Stock motors, the default timing is 40 degrees; for the (3.5T~8.5T) Modified motors, the default timing is 30 degrees.

As shown in the picture, turn the rear end plate clockwise can reduce the timing and turn it counter-clockwise can increase the timing.

• Increasing the timing can increase the motor speed (/RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing

usually requires a high(er) ratio.

• Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the

user manual of the ESC.

• After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about

the motor temperature via a infra-red temperature gun or the LCD program & a laptop (with the Hobbywing USB Link APP installed) or the WiFi module &

smart phone (with the Hobbywing WiFi Link App installed). If the temperature is too high, please let the motor cool down first and then test again. If the

OPTIONS

Notes:

• The KV value is measured when no load is applied to the motor, the motor timing is set to the value by default and the ESC timing is set to Zero. The default timing for the 3.5T~8.5T

motors is 30 degrees, and the default timing for the 10.5T~25.5T motors is 40 degrees.

• Never allow the motor to get overheat, because high temperatures may affect its performance. Please let the motor cool down before using it again in case that it gets too hot.

• The input current corresponding to the maximum output power can be instructive for load configuration & ESC selection, we strongly suggest not allowing the load to be higher tha

the input current corresponding to the maximum output power.

SPECIFICATIONS

RECOMMENDED FDR

3.5T 4.5T 5.5T 6T 6.5T

7.4 1：

6.6 1：

35mm

10.0 1：

10.2 1：

12.6 1：

7.3 1：

6.4 1：

36mm

9.5 1：

9.7 1：

12 1：

Modified

TC (Small Track)

TC (Big Track)

1/12th TC

2WD Off-road

4WD Off-road

4WD Truck

8.2 1：

7.5 1：

29mm

7.8 1：

7.0 1：

32mm

10.8 1：

11.8 1：

13.5 1：

7.6 1：

6.8 1：

34mm

10.5 1：

11.0 1：

13 1：

25mm

7.5T

7.2 1：

6.2 1：

36mm

9.1 1：

9.3 1：

11.5 1：

7.1 1：

6.1 1：

37mm

8.7 1：

8.9 1：

11 1：

8.5T

7.0 1：

6.0 1：

38mm

8.25 1：

8.5 1：

10.4 1：

N/A

10.5T

5.5 1：

5.0 1：

42mm

8.0 1：

9.0 1：

STOCK

TC (Small Track)

TC (Big Track)

1/12th TC

2WD Off-road

4WD Off-road

4WD Truck

13.5T

4.7 1：

4.0 1：

51mm

7.0 1：

8.0 1：

17.5T

4.0 1：

3.5 1：

66mm

6.0 1：

7.0 1：

21.5T

3.5 1：

3.0 1：

66mm

5.5 1：

6.5 1：

25.5T

3.2 1：

2.7 1：

66mm

5.2 1：

6.2 1：

Table

One

Table

Two

Thanks for purchasing Hobbywing XERUN V10 G3 motor. This sensored brushless power

system is very powerful, any improper usage can be dangerous and may damage the product

and related devices. Please take your time and read through the following instructions before

you start using the motor. We have the right to modify the product design, appearance,

features and usage requirements without notification. We, Hobbywing, are only responsible

for our product cost and nothing else are result of using our product.

PARTS LIST

The V10 G3 motor contains the following parts:

Front End Plate x 1Pcs

Rotor x 1Pcs

Stator x 1Pcs

Sensor Module x 1Pcs

Short Screws (M2.50) x 1Pcs

Long Screws (M2.50 x 45mm) x 3Pcs

Sensor Wires (80mm, 200mm) x 2PcsRear End Plate x 1Pcs

30401106

30401102

30401116

30401107

30401117

30401109

30401118

30401110

30401119

30401111

30401112

30401103

30401104

30401105

30401113

9450

7340

6500

5900

5500

5120

4800

4420

4200

3970

4500

3710

2830

2250

1500

0.0018

0.0029

0.0035

0.0041

0.0048

0.0056

0.0065

0.0074

0.0089

0.0097

0.0158

0.0251

0.0402

0.0645

0.1055

7.7

6.7

5.5

4.5

3.9

3.5

3.3

2.8

5.5

4.5

3.9

2.8

1.6

462

457

443

426

415

402

364

346

320

298

260

216

152

118

126

122

118

115

113

106

100

3.5T

4.5T

5.5T

6.5T

7.5T

8.5T

10.5T

13.5T

17.5T

21.5T

25.5T

Model

(Turns)

(No-load)

Resistance

( )Ω

LiPos

No-load

Current

(A)

Max.

Output

Power

(W)

Current

@Max.

Output

Power (A)

Diameter/

Length

(mm)

Shaft

Diameter/

Length (mm)

Stock

Rotor Weight

（）g

Poles

Applications

Φ5-12.1

Φ5-12.3

Φ7.3-12.5

-U

Φ7.3-12.3

-U

Φ5-12.5

Ø=35.9mm

(1.41in)

L=51.2mm

(2.01in)

Ø=35.9mm

(1.41in)

L=50.5mm

(1.99in)

Ø=3.17mm

(0.125in)

L=14mm

(0.55in)

35.9/51.2mm

(1.41in/2.01in)

3.17/13

（）0.125in/0.51in

Ø=3.17mm

(0.125in)

L=13.3mm

(0.52in)

163 5.75oz（）

159 5.60oz（）

163 5.75oz（）

162 5.71oz（）

164 5.78oz（）

161 5.68oz（）

160 5.64oz（）

163 5.75oz（）

133 4.69oz（）

131 4.62oz（）

135 4.76oz（）

154 5.43oz（）

2-3S

Modified Class of 1/10

th &

1/12th On-road Racing

1/10th Drift, 2WD Off-road Racing

Stock Class of 1/10

th On-road Racing

1/10th Stock Class Racing,

Rock Crawler

Modified Class of 1/10

4WD Off-road Racing

1/10th Drift, Stock Class of 1/10

On-road Racing

The FDR (Final Drive Ratio) is the ratio between the angular velocities of the pinion gear and the tyres. In simple terms, the number of laps the motor will rotate when the tyres spin one lap.

Different conditions like track type, grip, tyres, temperature, vehicle weight, gearing mode, driving mode influence the performance of your vehicle and have different requirements on the power system, therefore

one FDR can not be applicable for all conditions.

All the values in Table One are the FDRs recommended for vehicles using different G3 Modified motors; all the values in Table Two are the FDRs recommended for vehicles using different G3 Stock motors in the

Blinky mode. If you don’t know how to set the FDR, please refer to the following tables. If no recommended FDR is applicable to your vehicle, please start with a big FDR and then adjust gradually as per the

demand.

Notes:

• For the modified applications (listed above), please do not set the ESC timing to a very high value, because overload may damage your motor. If you have no idea about the timing setting, please start with 0 and

increase the value gradually, and ensure the motor temperature won’t go above 90 (/194 ).℃ ℉

Rotor x1

Stator x1

Sensor module

Short screws x1

M2.50

Long screws x3

M2.50 x 45mm

Rear end plate

Install the rear end plate Install the rotor

Fasten the rear end plate with those long screws Finished product

Install the sensor module

Install the front end plate

1 2 3

4 5 6

The XERUN V10 G3 Motor is very strong in construction but also easy to disassemble for maintenance.

We recommend checking the bearings and cleaning the motor periodically..

Please follow the steps (as shown below) to assemble the motor. When disassembling the motor, the sequences are reversed.

ASSEMBLY & DIS-ASSEMBLY

• To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the

motor to related devices.

• Never allow this product or other electronic components to come in contact with water, oil, fuel or

other electro-conductive liquids. If it happens, stop the use of the product immediately and let it

dry carefully.

• Read through the manuals of all power devices and chassis and ensure the power configuration is

rational before using this unit.

• Never apply full throttle if the pinion gear is not mounted on, because (under the no-load

circumstances) high RPMs may get the motor damaged.

• Please connect all the devices carefully, you may not control the vehicle properly or encounter some

unpredictable issues like damaged components if any poor connection exists.

• To avoid possible damage (result from overheat) to the product, please control the soldering time within

5 seconds when soldering the motor wires (a soldering iron with the power of at least 60W is needed).

• Stop immediate usage once the casing of the motor exceeds 100 /212 as high temperature ℃ ℉

may damage the motor and cause the rotor to demagnetize. Hobbywing recommends activating

the “Motor Thermal Protection” (of the ESC).

PNOptional Part Part Name Description

30820018

30820017

30820019

30820020

30820400

Applications (/Motors)

10.5T-21.5T

3.5T-8.5T

25.5T

XERUN-V10-G3-Rotor-D7.3*D12.5*t24.1

XERUN-V10-G3-Rotor-D5*D12.3*t24.1

XERUN-V10-G3-Rotor-D5*D12.1*t24.1

XERUN-V10-G3-Rotor-D5*D12.5*t24.1

XERUN-V10-G3-Rotor-D7.3*D12.3*t25.2

It’s the standard rotor for the (10.5T~21.5T) Stock motors; with this rotor,

torque & RPM of your motor won’t be bad.

With this rotor, your motor will have the better accelerating and braking linearity and high RPM.

With this rotor, your motor will have the better accelerating and braking linearity and be smoother

during the high-speed operation. It’s specially applicable for the track with intermediate/low grip.

It’s the standard rotor for the 5.5T~8.5T motors.

It’s a rotor specially designed for the 25.5T motor.

Rotor

Product specificaties

Merk:	Hobbywing
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	Xerun V10 G3-6.5T OnRoad Spec
Kleur van het product:	Zwart
Soort:	Radio-Controlled (RC) Model Parts
Correct gebruik:	Auto
Materiaal:	Aluminium
Merkcompatibiliteit:	Hobbywing
Aantal:	1
Type product:	Motor
Type motor:	Borstelloze motor
Aantal palen:	2
Aslengte:	13.3 mm
Asdiameter:	3.17 mm
Motorsnelheidsconstante (KV):	6300 RPM/V
Lengte motor:	51.2 mm
Stroomsterkte zonder belading:	7.4 A