Hobbywing EZRUN 4278SD G2 Handleiding

Hobbywing Radiografisch bestuurbaar speelgoed EZRUN 4278SD G2

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobbywing EZRUN 4278SD G2 (1 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

• Please carefully check power devices and manual of car frame to ensure the power pairing is

reasonable. Avoid wrong pairing to overload and damage the motor.

• Always wire up all the parts of the equipment carefully. If any of the connections come loose as a

result of vibration, your model RC may lose control.

• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load,

the motor may get damaged.

• Never allow the motor case to get 100 degrees Celsius (212 degrees Fahrenheit) because the

magnets maybe demagnetized by high temperature.

Warnings

Thank you for purchasing this HOBBYWING product! The power of brushless power system is

powerful. Any improper use may cause personal injury and damage to the product and related

devices. We strongly recommend reading through this user manual before use and strictly

abide by the specified operating procedures. We shall not be liable for any liability arising from

the use of this product, including but not limited to reimbursement for incidental or indirect

losses. Meanwhile, we do not assume any responsibility caused by unauthorized modification

of the product. We have the right to change the product design, appearance, performance

and use requirements without notice.

CA UT IONS

AT T ENT ION

02 Features

03 Specifications

Model

KV Value

Lipo Cells

Resistance

No-load current

Outer Diameter/Length

Shaft diameter/Exposed shaft length

Bearing size(mm)

Pole

Weight

Application

30402800

2250KV

3-6S Lipo

0.0048Ω

5.0A

42mm 1.654in / 78mm 3.071in( ) ( )

5mm 0.197in / 18.5mm 0.728in( ) ( )

Front: D16*D5*T5 Rear: D11*D5*T5

455g

1/8 Truck, Monster Truck

EZRUN 4278SD G2

30402751

2500KV

3-4S Lipo

0.0065Ω

4.8A

42mm 1.654in / 68mm 2.677in( ) ( )

5mm 0.197in / 18.5mm 0.728in( ) ( )

Front: D16*D5*T5 Rear: D11*D5*T5

355g

1/8 Buggy, 1/10 Heavy-duty Monster Trcuk

EZRUN 4268SD G2

USER MANUAL

EZRUN 4278SD/4268SD G2

Sensored Brushless Motor

20220304

• Chip built in the motor,when matched with Hobbywing EZRUN MAX8 G2 esc, it not only has perfect compatibility, the ESC can automatically identify the motor and build a pure/full sensor mode power system, providing better

manipulating performance and more delicate manipulating feel.

• The rotor adopts four strong magnetic and high temperature resistant sintered Nd-Fe-B magnets, widens the magnetic tile, provides super torque, and makes the motor have strong explosive force and stable output power.

• The independent high-precision encoder always outputs pure rotor position signal, which effectively avoids the interference of sensor signal and makes the motor work stably in sensor state.

• High output efficiency, effectively reduce the motor temperature and output more power under the same load.

• CNC machined aluminum housing, high purity copper windings, advanced rotor structure, 0.2mm silicon steel laminations, high-quality stainless steel output shaft, high-precision bearing for high durability and smoothness.

• The innovative new sensor interface and rubber cover bearing have better waterproof and dustproof effect than the traditional sensor motor.

78 ± 0.318.5 ± 0.5

40.8

4.5 Cut

14.5

4-M3 4-M4

25.40

22.5°

C.C.W

Dim.of cooling fins

3- 6.5 GBC

R42

Reasonable selection of gear ratio is very important. Improper gear ratio may bring you great loss. You can select the gear ratio according to the following points!

The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation. Because high temperature may cause the magnets to get demagnetized, the coil to get melt and short circuited, and

the ESC to get damaged. A suitable gearing ratio can effectively prevent the motor from overheating.

To avoid the possible damage to ESC and motor caused by the overheat, please start with a small pinion/a big FDR and check the motor temperature regularly. If the motor and ESC temperature always stay at a low level

during the running, you can change a big pinion/a low FDR and also check the motor temperature regularly to ensure that the new FDR is suitable for your vehicle, local weather and track condition. (Note: For the safety of

electric devices, please check the ESC and motor temperature regularly.)

05 Gearing

06 Assembly and Disassembly

In order to make the motor have longer service life and higher efficiency, we suggest to regularly check the bearing and clean the dirt in the motor. The specific time depends on the frequency of using the motor and

the site conditions. When installing, please follow the steps in the following assembly drawing; when disassembling, follow the reverse steps.

Parts List

04 Installation & Connection

The specifications of mounting hole screws are two sets of M4 and two sets of M3, and the mounting holes

are 5.5mm in depth, before installing the motor on the vehicle, please carefully confirm whether the

specification of the screws is appropriate according to the thickness of the motor mounting plate to avoid

damage to the motor due to too long screws.

• When connecting the motor and esc, please pay attention to the marked three-phase position of A, B and

C to ensure that the three wires of the motor and esc are connected correspondingly. Otherwise, it cannot

run normally and even damage the esc and motor.

That is: Wire A of the esc matches wire A of the motor, wire B of the esc matches wire B of the motor,

wire C of the esc matches wire C of the motor.

• When the sensor wire of the motor is connected with the sensor wire of the esc, it shall be connected

correspondingly according to the arrow mark on the sensor interface.

Before power on the esc, please check the reliability of the motor installation and the correctness of all

connections.

Back End Bell x 1Pcs

Screws for Fastening

the Back End Bell x 3pcs

(M2.5x4mm)

Screws for Fastening the Front

End Bell x 6Pcs (M2.5x5mm)

1. Mount the motor rotor

4. Mount the back end bell set

5. Mount screws for fastening

the back end bell

2. Mount the front end bell set

3. Mount screws for fastening

the front end bell

6. Picture of the assembled motor

1 2 3

4 5 6

Stator Set x 1Pcs

Front End Bell x 1pcs

Rotor x 1Pcs

Switch

Motor

Electronic Speed Controller

Motor B

Motor C

Motor A

68 ±0.3

4.5 Cut

14.5

18.5 ±0.5

4-M3 4-M4

25.40

22.5°

C.C.W

R42

Dia. of cooling fins

3- 6.5 GBC

EZRUN 4278SD G2 EZRUN 4268SD G2

Product specificaties

Merk:	Hobbywing
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	EZRUN 4278SD G2
Kleur van het product:	Grijs
Gewicht:	355 g
Correct gebruik:	Buggy, Truck
Merkcompatibiliteit:	Hobbywing
Lengte:	68 mm
Type product:	Motor
Type motor:	Borstelloze motor met sensor
Aantal batterijcellen:	3-4S
Niet voor kinderen 0 - 3 jaar:	Ja
Bearing technologie:	Dubbele kogellager
Motor diameter:	42 mm
Asdiameter:	5 mm
ESC-programmeerondersteuning:	Ja
Motorsnelheidsconstante (KV):	2500 RPM/V
Stroomsterkte zonder belading:	4.8 A