Hobbywing Ezrun 1626 Handleiding

Hobbywing Radiografisch bestuurbaar speelgoed Ezrun 1626

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobbywing Ezrun 1626 (1 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Thank you for purchasing this HOBBYWING product! The

power of brushless power system is powerful. Any

improper use may cause personal injury and damage to the

product and related devices. We strongly recommend

reading through this user manual before use and strictly

abide by the specified operating procedures. We shall not

be liable for any liability arising from the use of this

product, including but not limited to reimbursement for

incidental or indirect losses. Meanwhile, we do not assume

any responsibility caused by unauthorized modification of

the product. We have the right to change the product

design, appearance, performance and use requirements

without notice.

CA UT ION S

AT T ENT IO N

P Lart sist

02 Features

04 I sn ta at on onne t onll i &Cci

05 Gear ngi

06 A emb y and D a emb yss l is ss l

03 Spe f at onci icis

01 Warn ngis

• Specially designed for 1/28 mini car when matched with Hobbywing EZRUN MINI28 esc, it has perfect compatibility, and provides ，

better performance and more delicate manipulating feel.

• The front and rear ends of the motor are designed with large openings structure to provide better heat dissipation for the motor.

• Built in high-precision Hall sensor combined with the high precision and balanced rotor to ensure excellent linearity of the motor.

• The internal PCB is a 4-layer board, and the ABC wiring position is reinforced by punching holes,prevent the soldering spot from falling

off after multiple soldering.

• Please carefully check power devices and manual of car frame to ensure the power pairing is reasonable. Avoid wrong pairing to

overload and damage the motor.

• Always wire up all the parts of the equipment carefully. If any of the connections come loose as a result of vibration, your model RC

may lose control.

• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged.

• Never allow the motor case to get 100 degrees Celsius (212 degrees Fahrenheit) because the magnets maybe demagnetized by high

temperature.

In order to make the motor have longer service life and higher efficiency, we suggest to regularly check the bearing and clean the dirt in the

motor. The specific time depends on the frequency of using the motor and the site conditions. When installing, please follow the steps in the

following assembly drawing; when disassembling, follow the reverse steps.

Reasonable selection of gear ratio is very important. Improper gear ratio may bring you great loss. You can select the gear ratio according

to the following points!

1. The running temperature of the motor

The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation. Because high temperature

may cause the magnets to get demagnetized, the coil to get melt and short circuited, and the ESC to get damaged. A suitable

gearing ratio can effectively prevent the motor from overheating.

2. The principle of selecting gear ratio

To avoid the possible damage to ESC and motor caused by the overheat, please start with a small pinion/a big FDR and check the

motor tempera ture regularly. If the motor and ESC temperature always stay at a low level during the running, you can change a big

pinion/a low FDR and also check the motor temperature regularly to ensure that the new FDR is suitable for your vehicle, local weather

and track condition. (Note: For the safety of electric devices, please check the ESC and motor temperature regularly.)

1. Install the motor

There are 8 motor mounting holes in M2 specification, and the mounting holes are 2.5mm in depth, before installing the motor on

the vehicle, please carefully confirm whether the specification of the screws is appropriate according to the thickness of the motor

mounting plate to avoid damage to the motor due to too long screws.

2. How to Connect the Motor to an ESC

• When connecting the motor and esc, please pay attention to the marked three-phase position of A, B and C to ensure that the three

wires of the motor and esc are connected correspond ingly. Otherwise, it cannot run normally and even damage the esc and motor.

That is: Wire A of the esc matches wire A of the motor, wire B of the esc matches wire B of the motor, wire C of the esc matches wire C

of the motor.

• Connecting the sensor cable to the motor and esc.

3. Inspection

Before power on the esc, please check the reliability of the motor installation and the correctness of all connections.

Model

EZRUN-1626SD-3500KV

EZRUN-1626SD-5000KV

EZRUN-1626SD-6500KV

3500KV

5000KV

6500KV

LiPos

0.4A

0.5A

0.6A

No-load

Current

(A)

Diameter/Length

(mm)

2S ϕ=16mm (0.63in)

L=26mm (1.02in)

ShaftDiameter/

Length (mm)

ϕ=2.0mm (0.08in)

L=8.5mm (0.33in)

Bearing size

(mm)

D5*D2*T2.5

Poles

Weight

(g)

1/28 Mini

Applications

18g

USER MANUAL

EZRUN 1626SD

Sensored Brushless Motor

20221026

18.5

(

0.62")

8.5

±0.5

±0.2

(1.02")

1.80

（

0.78")

8-M2 EQS

(

0.47")

45°EQS

C.C.W

Rear End Bell x 1Pcs

Screws for Fastening

the Rear End Bell x 2Pcs

(M1.6 x 4mm)

Stator Set x 1Pcs

Rotor x 1Pcs

1. Mount the motor rotor

3. Mount screws for fastening

the rear end bell 4. Picture of the assembled motor

2. Mount the rear end bell set

1 2

3 4

(A)

(C)

(B)

Battery

Electronic Speed Controller

Receiver Motor

Sensor wire

Sensor port of motor

Product specificaties

Merk:	Hobbywing
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	Ezrun 1626
Kleur van het product:	Zwart
Gewicht:	18 g
Merkcompatibiliteit:	Hobbywing
Compatibiliteit:	1/28th Mini
Type product:	Motor
Type motor:	Borstelloze motor met sensor
Motor diameter:	16 mm
Aantal palen:	2
Aslengte:	8.5 mm
Asdiameter:	2 mm
Motorsnelheidsconstante (KV):	5000 RPM/V
Lengte motor:	26 mm
Stroomsterkte zonder belading:	0.5 A