Hobbywing QUICRUN 2030SL G2 6500KV Handleiding

Hobbywing Radiografisch bestuurbaar speelgoed QUICRUN 2030SL G2 6500KV

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobbywing QUICRUN 2030SL G2 6500KV (1 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Thank you for purchasing this HOBBYWING product! Improper use

may cause personal injury and damage to the product and related

devices. We strongly recommend reading through this user manual

before use and strictly abide by the specified operating procedures.

We shall not be liable for any liability arising from the use of this

product, including but not limited to reimbursement for incidental

or indirect losses. We do not assume any responsibility caused by

unauthorized modification of the product. We have the right to

change the product design, appearance, performance and use

requirements without notice.

CA UT ION S

AT T ENT IO N

03 Installation & Connection

04 Gearing

02 Specifications

01 Warnings

• Read the manuals of all the items being used in the build.Ensure gearing,setup,and overall install is correct and reasonable.

• All connections,must be made correctly.You may loose control,or run into major issues caused by improper, bad,weak,or poor connections.

• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged.

• Stop usage if the motor exceeds 100 ,high temperature will damage the motor and cause the rotor to weaken.℃/212℉

Reasonable selection of gear ratio is very important. Improper gear ratio may cause damage. You can select the gear ratio according to the following points!

The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation. High temperature may cause the magnets

to get demagnetized, the coil to melt and short circuit, and the ESC to get damaged. A suitable gearing ratio can effectively prevent the motor from

overheating.

To avoid the possible damage to ESC and motor caused by the overheating, please start with a small pinion/a big FDR and check the motor temperature

regularly. If the motor and ESC temperature always stays at a low level during the running, you can change a larger pinion/a lower FDR and also check the

motor temperature regularly to ensure that the new gearing is suitable for your vehicle, local weather and track condition. (Note: For the safety of electric

devices, please check the ESC and motor temperature regularly.)

There are 6 motor mounting holes in M2.5 specification, and the mounting holes are 3.8mm in depth,before installing the motor on the vehicle, please

carefully confirm whether the specifications of the screws are appropriate, as not to damage the motor due to excessive length. There are three types of

mounting hole spacing of the motor, one group is 12.6mm, one group is 14mm, and one group is 16mm. Refer to the motor outline drawing for details.

There is no specific wire sequence requirement for the connection between the motor and the esc,the # A/# B/# C three wires of the motor and esc can be

connected at will, if the motor rotation in the opposite direction, you can exchange any two wires.

Before powering on the esc, please check the motor installation and the order of all connections.

20240409

USER MANUAL

QUICRUN 2030 G2

Sensorless Brushless Motor

HW-SMB333DUL00

SHENZHEN HOBBYWING TECHNOLOGY Co., LTD. · 101-402 Building 4, Yasen Chuangxin Hi-tech Industrial Park, 8 Chengxin Road, Baolong Industrial Town, Longgang District, Shenzhen, China. April 09, 2024

GBC3- 3.5

0.79"）

（

1.70

31 ±0.3012 ±0.50

（0.47"）（1.22"）

9.30

C.C.W

6-M2.5

Ø16

Ø14

12.60 Ø