Chef's Choice 480KS Handleiding
Chef's Choice
Messenslijper
480KS
Lees hieronder de š handleiding in het Nederlandse voor Chef's Choice 480KS (12 pagina's) in de categorie Messenslijper. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
MOdel 480KS inStructiOnS
Manual Diamond HoneĀ®
Knife & Scissors Sharpener
Read these instructions before use.
It is essential that you follow these
instructions to achieve optimum results.
inStructiOnS
Congratulations! You have selected the worldās ļ¬rst professional compact knife
and scissors sharpener, invented and made in the U.S.A. by EdgeCraft: the
worldās leading manufacturer of sharpeners. The EdgeCraft 480KS includes an
assortment of accessories to meet a wide range of sharpening needs. To get the
most from your new compact sharpener please follow these instructions.
The Model 480KS, See Figure 1, consists of the 2-Stage Knife Sharpener, two (2)
diamond coated abrasive pads, and three (3) Scissors Angle Guides.
The sharpener is shown at upper left ā Figure 1 with the Fine grit diamond pad in
place on top of the sharpener. That abrasive pad, held in place by a magnetic strip
(not shown) recessed under the pad, can be removed and stored in the compart-
ment under the sharpener.
The sharpener shown in the upper right is turned over to show the open storage
compartment on its underside with the compartment cover removed.
There are two (2) different diamond coated pads, Coarse and Fine. The Fine grit
pad has a ruled groove along its length on the diamond coated side in order that
it can be readily identiļ¬ed. The Coarse grit pad is ungrooved. The abrasive pads
held in place on top of the sharpener by the built-in magnet can be removed from
the magnet with a ļ¬nger nail or by inverting the sharpener and tapping it lightly
on the table.
There are three (3) differently colored Scissors Sharpener Angle Guides.
Follow the Detailed Instructions carefully to insure perfect results.
Figure 1: Model 480KS Knife and Scissors Sharpener and its components.
Figure 4: Sharpening in Stage 2.Figure 3: Sharpening in Stage 1.
Knife Sharpening
The ChefāsChoiceĀ® 480 KS Knife and Scissors Sharpener is equipped with a
2-stage knife sharpening section with built-in angle guides that take the guess-
work out of sharpening and 100% diamond abrasives that sharpen quickly and
efļ¬ciently! Knives are sharpened ļ¬rst with medium diamond abrasives in Stage 1
then with ļ¬ne diamond abrasives in Stage 2. The sharpening angle in both stages
is precisely controlled by roller angle guides (Fig. 2).
First, familiarize yourself with the parts of the sharpener (Fig. 2). Always start
with a clean knife. Place the sharpener on a ļ¬at surface, near the edge of a
table or other secure work surface. Hold the sharpener with ļ¬ngers safely behind
the Guard Rib and place the blade in Stage 1: the slot nearest to the Guard Rib
(Fig. 3). Make sure the blade leans ļ¬rmly against the roller guides. Without any
downward pressure, move the blade back and forth in the Stage 1 slot until the
blade is sharp. Keep your eyes on the roller guides; one or both should turn as you
pull the knife back and forth to ensure the knife is at the correct angle. Both sides
of the edge will be sharpened at the same time.
Next, place the knife in the Stage 2 slot, (Figure 4) making sure the blade leans
ļ¬rmly against the roller guides and repeat the back and forth movement to reļ¬ne
and further sharpen the edge. Usually, only 25 back-and-forth strokes are needed
in Stage 1 and about 5 back-and forth strokes in Stage 2. It is important to keep
the blade in contact with the knife roller guides at all times and apply little to
no downward pressure on the blade. If the knife is not sharp enough, repeat the
steps described above for both Stages
1 and 2.
SUGGESTIONS: If youāre right-handed,
hold the handle in the left hand and the
knife in the right. If left-handed, reverse
hands. Just remember to start sharpen-
ing in the slot nearest the handle (Stage
1). You wonāt need any sharpening oils,
lubricants, water or other liquids. Stage Figure 2: Knife sharpener parts.
Magnetic Holder
Guard Rib Roller Angle
Guides
Stage 2
(Fine)
Stage 1
(Medium)
Knife
Sharpening
Product specificaties
| Merk: | Chef's Choice |
| Categorie: | Messenslijper |
| Model: | 480KS |
Heb je hulp nodig?
Als je hulp nodig hebt met Chef's Choice 480KS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Messenslijper Chef's Choice
8 Januari 2024
8 Januari 2024
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
Handleiding Messenslijper
- Messenslijper IKEA
- Messenslijper Krups
- Messenslijper Adler
- Messenslijper Ambiano
- Messenslijper Bartscher
- Messenslijper Bavaria
- Messenslijper Beper
- Messenslijper Berkel
- Messenslijper Bifinett
- Messenslijper Blokker
- Messenslijper Bomann
- Messenslijper Domo
- Messenslijper EdgeCraft
- Messenslijper Einhell
- Messenslijper Fagor
- Messenslijper Gardenline
- Messenslijper Gastroback
- Messenslijper Gourmetmaxx
- Messenslijper Graef
- Messenslijper Gude
- Messenslijper Melissa
- Messenslijper Powerplus
- Messenslijper Presto
- Messenslijper Princess
- Messenslijper Roadstar
- Messenslijper Salter
- Messenslijper Silvercrest
- Messenslijper Sogo
- Messenslijper Steba
- Messenslijper Studio
- Messenslijper Tower
- Messenslijper Trebs
- Messenslijper Ozito
- Messenslijper Clatronic
- Messenslijper Guzzanti
- Messenslijper OBH Nordica
- Messenslijper Orbegozo
- Messenslijper Tacklife
- Messenslijper Eldom
- Messenslijper Waring Commercial
- Messenslijper Brentwood
- Messenslijper Herkules
- Messenslijper Genie
- Messenslijper C3
- Messenslijper Orava
- Messenslijper Alpha Tools
- Messenslijper For_Q
- Messenslijper WĆ¼sthof
- Messenslijper Work Sharp
- Messenslijper Petra Electric
- Messenslijper GARDE
- Messenslijper IdeenWelt
- Messenslijper Donau Elektronik
- Messenslijper Sharpal
Nieuwste handleidingen voor Messenslijper
5 December 2024
4 December 2024
4 December 2024
17 November 2024
17 November 2024
16 November 2024
5 September 2024
15 Augustus 2024
15 Augustus 2024
15 Augustus 2024