Swann SW351-KCG Handleiding

Swann Niet gecategoriseerd SW351-KCG

Lees hieronder de 📖 handleiding in het Nederlandse voor Swann SW351-KCG (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Operating Instructions

Magnetic Keypad

Door Alarm

SW351-KCG

™

Advanced security made easy

2222

IMPORTANT - Read Before Installing

Do not• install the alarm unit near devices which generate magnetic ﬁelds (such as

microwaves).

Do not• install any the alarm unit in direct sunlight.

Use only alkaline batteries.•

All components are for indoor use only.• Do not install outdoors.

Replace the batteries in the unit every six months.•

Test the alarm periodically• (every 1 - 2 months and each time you change the

batteries) to ensure it is working properly.

This alarm system is designed to be, and acts as, a theft deterrent. This system, •

like any other, cannot offer complete protection for your home or business - it

is simply an alarm system. Like all practical systems, it has limitations and it could be

disabled by a skilled intruder. We suggest that you avoid relying solely on this magnetic

switch alarm to protect your property, but use it as part of a comprehensive security

solution. You can increase your level of protection through the use of high-quality

locks, stronger doors, guards for your windows and a CCTV system and recording

devices.

About the Alarm Unit

Congratulations on your purchase of this

keypad controlled magnetic alarm from

Swann! This simple but powerful stand-

alone alarm unit can be used to secure

almost any door or window you want.

Selecting Modes

The is located within the battery compartment.Mode Select Switch

Alarm Mode: When the alarm is tripped, a thirty second countdown will begin - the

indicator LED on the front of the alarm unit will ﬂash during this countdown. During this

time, the alarm can be disarmed by entering your passcode. If the passcode is not entered,

the alarm will sound at full volume.

Chime Mode: Each time the alarm is tripped, the alarm unit will chime, much like a doorbell.

The alarm does not need to be armed.

Arming Delay

When you use your passcode to arm the system, it will enter an arming delay of forty-ﬁve

seconds. The indicator LED will ﬂash during this time, and the alarm cannot be tripped. This

is intended to give you time to arm the alarm unit and leave the area.

Operating Instructions

Siren

Magnetic Detector

Indicator LED

Keypad

Magnetic

Detector

Installation

The alarm unit should be mounted on a door or window frame, and the magnetic trigger

should be mounted on the door or window itself. When the door/window is closed, two

black arrows (the one on the trigger and either one on the alarm unit) should be as close to

touching as practicable.

To mount the alarm unit:

Attach the alarm unit using one of the provided screws - the mounting hole is in the •

upper centre on the rear of the alarm unit.

Using the two smaller screws, attach the magnetic trigger to the door/window. Ensure •

that when the door or window is shut that the two black arrows are as close to

touching as they can be. The alarm will be triggered if the arrows are moved more than

approximately 1/3” (about 8-10mm) apart.

Setting your Passcode

Your passcode must be four digits long, and should be something that you will remember.

Try to avoid obvious combinations (such as 1234 or similar).

To set your passcode:

Open the battery compartment and press the button labeled •

LEARN.

Enter your four digit passcode. When entering the passcode, •

press buttons slowly and deliberately, waiting for the alarm

unit to beep quickly to conﬁrm each button press.

A louder, longer beep will conﬁrm that a new passcode has •

been set.

Replacing Batteries

The batteries in the alarm unit should be replaced every six months. If you’re using the

sensor in chime mode and get a lot of visitors, you may need to change them more often.

Open the battery compartment and remove any batteries already installed.•

Replace with three fresh alkaline AAA batteries. Do not mix battery types. Do not use •

rechargeable batteries.

Low Battery Indicator

When the batteries in the alarm unit are running out, the LED on the front of the alarm unit

will ﬂash slowly (more slowly than during the arming delay). If the LED starts ﬂashing in this

way, change the batteries as soon as possible.

Technical Speciﬁcations

General

Power Requirements 3 x Alkaline AAA

Batteries (4.5V DC)

Modes 2 (Alarm and Chime)

Chime Mode

Chime Volume > 90dB

Chime Duration Approx. 2s

Re-Trigger Delay 5s

Alarm Mode

Passcode Protected Yes (4-digit numerical code)

Passcode Learning Duration 15s

Siren Volume > 110dB

Siren Duration 30s

Entry Delay 30s

Exit Delay 45s

Re-Trigger Delay 5s

Inside the Battery Compartment

showing the Mode Switch and

LEARN button.

Product specificaties

Merk:	Swann
Categorie:	Niet gecategoriseerd
Model:	SW351-KCG
Kleur van het product:	Wit
Soort:	Draadloze sirene
Ondersteund aantal accu's/batterijen:	3
Batterijtechnologie:	Alkaline
Type batterij:	AAA
Alarm decibels:	110 dB
Alarm duur:	30 s