Bobrick B-166 1836 Handleiding

Bobrick Niet gecategoriseerd B-166 1836

Lees hieronder de 📖 handleiding in het Nederlandse voor Bobrick B-166 1836 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 6/10/21
R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2021 by Bobrick Washroom Equipment, Inc.
Technical Data
Designer’s Notes:
1. Special-order sizes available on request.
2. Maximum size mirror available, 60'' x 48'' (152 x 122cm) or 48'' x 60'' (122 x 152cm); minimum size, 12" x 12"
(30 x 30cm).
3. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions of mirror, not
including shelf. EXAMPLE: B-166 2436'' (61 x 94cm) mirror will be furnished 24'' x 37-1/4'' (61 x 94cm) outside-of-
frame to outside-of-frame including shelf.
4. To specify special sizes use Series Number followed by width x height in inches. EXAMPLE: B-166 2024 20"x 24"
(51 x. 61cm).
5. Bobrick framed mirror/shelf models are manufactured to a tolerance 1/8'' (3.2mm).±
6. For sufficient space to lift mirror onto wall hanger(s), provide 1" (25.4mm) minimum clearance above top of
mirror frame.
7. Provide 1'' (25mm) minimum clearance at bottom of mirror for unlocking mirror from wall and 1/2''
(12.7mm) minimum clearance on each side.
Figure: 1
MIRROR WITH
STAINLESS STEEL
CHANNEL FRAME
AND SHELF
B-166
SERIES
Snap Locking Design
(Rear View)
"2S" Tab Design
(Rear View)
Figure: 2
Note: Mirrors greater than 36" in width will have multiple
hanger brackets with a typical 8" o󰀨 each edge.
1/2''
13mm
5-9/16''
141mm
3/8''
19mm
2-1/2''
65mm S
2-9/16''
65mm
S
4'' or 5" Typ.
100 or 125mmS
Side View
Back Plate/Wall Hanger
Frame
Mirror
Finish Face of Wall
Frame
Mirror
S
SS
1" to 1-1/2"
25mm to 40mm
S
Half
Mirror Width
4"
100mm Typ.
Mirror Bracket w/Tape
2-7/8"
75mm
Mirror
Bracket
1/2"
13mm
Finish Face
of Wall
1-5/16"
33mm
4"
100mm
3/4"
19mm
STANDARD B-166 SERIES MIRRORS
MODEL
NO.
OVERALL SIZE
W H
B-166 1824 18'' (46cm) 25-1/4'' (64cm)
B-166 1830 18'' (46cm) 31-1/4'' (79cm)
B-166 1836 18'' (46cm) 37-1/4'' (94cm)
B-166 2436 24'' (61cm) 37-1/4'' (94cm)
All Other Size Mirrors
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-166 Rev. 6/10/21
R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2021 by Bobrick Washroom Equipment, Inc.
MATERIALS:
Frame — Type 430 stainless steel, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm) channel 1/4" (6mm) return at rear. For Snap Locking
Design; 1/2" x 1/2" x 1/2" (13 x 13 x 13mm) channel for "2S" Design Tab, with bright polished finish. One-piece frame with
90 degree mitered corners. Galvanized steel back has integral horizontal hanging brackets near the top for hanging the mirror
and near the bottom to prevent the bottom of the mirror from pulling away from the wall. Locking devices secure mirror to
concealed wall hanger.
Shelf — 18-8, type 304, 18-gauge (1.2mm) stainless steel with satin finish. Return edge on front, hemmed for additional
strength and safety. Once mounted properly, mirror shelf meets accessible design by protruding 4" (102mm) from the wall.
Mirror — No. 1 quality, 1/4" (6mm) select float glass: selected for silvering, electrolytically copper-plated by the galvanic
process, and guaranteed for 15 years against silver spoilage. Back is protected by full-size, shock-absorbing, water-resistant,
nonabrasive, polyethylene padding.
Concealed Wall Hanger — Heavy gauge steel construction. Incorporates upper and lower support members, which engage
backplate louvers to keep mirror against wall for Snap-locking design. Double-sided tape secures mirror to concealed wall
hanger for "2S" Design Tab design.
INSTALLATION:
Mount wall hanger on wall with screws (not furnished) at points indicated by an . For plaster or dry wall construction, S
provide backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing
a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall
surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or
expansion bolts. Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members.
To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1"
(25mm) above final position and then lowered into final position.
Place shelf below mirror and install with wall screws (not furnished) at points indicated by S.
Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final
position (see figure 3). Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror
near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.
"2S" Tab Design — Double-sided tape secures mirror to concealed wall hanger when it is lowered into final position (see
figure 4).
Figure: 3
"2S" Tab Design - Up to 36" Width
(Front View)
Snap Locking Design
(Front View)
Figure: 4
SPECIFICATION:
Mirror shall have a one-piece type 430 stainless steel channel frame, with 90 mitered corners; all exposed surfaces shall have °
bright polished finish. Shelf shall be type 304, 18-gauge (0.8mm) stainless steel with satin finish and shall have return edges
on front with front return edge hemmed. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. The
back shall be protected by full-size, shock-absorbing, water-resis tant, nonabrasive, polyethylene padding. Galvanized steel back
shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed wall hanger and to prevent
the mirror from pulling away from the wall.
Framed Mirror With Shelf shall be Model B-166 _______________ (insert width and height) of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
Aprox. 1"
25mm
Initial
Position
S
S
Final
Position
C
L
Aprox. 1"
25mm Initial
Position
S
S
Final
Position
C
L

Product specificaties

Merk: Bobrick
Categorie: Niet gecategoriseerd
Model: B-166 1836

Heb je hulp nodig?

Als je hulp nodig hebt met Bobrick B-166 1836 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Bobrick

Bobrick

Bobrick B-165 2436 Handleiding

4 April 2025
Bobrick

Bobrick B-166 1836 Handleiding

4 April 2025
Bobrick

Bobrick B-35643 Handleiding

25 September 2024
Bobrick

Bobrick ConturaSeries B-4112 Handleiding

11 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Mr Steam

Mr Steam LEDLITE Handleiding

4 April 2025
Auray

Auray BAC-4A4HB Handleiding

4 April 2025
Kernau

Kernau KSSI 2601 C Handleiding

4 April 2025
Savio

Savio TR-17 Handleiding

4 April 2025
Navman

Navman MiVue SmartBox III Handleiding

4 April 2025
Hortus

Hortus 211-900 Handleiding

4 April 2025
Sabrent

Sabrent CR-U4XB Handleiding

4 April 2025
Planet

Planet CS-6303R Handleiding

4 April 2025
Therm-a-Rest

Therm-a-Rest ProLite Handleiding

4 April 2025
Therm-a-Rest

Therm-a-Rest Trail Pro Handleiding

4 April 2025