Swann SWALPH-B400RWPK1 Handleiding

Swann Niet gecategoriseerd SWALPH-B400RWPK1

Lees hieronder de 📖 handleiding in het Nederlandse voor Swann SWALPH-B400RWPK1 (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/7
Wireless
Motion Sensor
Spotlight
Instruction Manual
with Remote Control
EN
Powered by Swann
2
PRODUCT OVERVIEW
LED Light
Sensor mode: 400 lumens
Manual mode: 200 lumens
Power OFF.
The spotlight will automatically
switch back to "Light on
Motion" mode after 1 hour if no
other button is pressed
Set LED Light to stay OFF
when motion is detected
Set Enforcer Lights to stay OFF
when motion is detected
Set motion sensor sensitivity
to Low. Detection range is up
to 3m/10ft
Set motion sensor sensitivity to
Medium. Detection range is up
to 6m/20ft
Override sensor and manually
turn LED Light ON for an
indeî´ªnite amount of time until
you press the Power OFF button
Infrared transmitter
Set LED Light to automatically
turn ON when motion is detected.
LED Light will turn off 20 seconds
after no motion is detected
Set Enforcer Lights to
automatically turn ON when
motion is detected. Enforcer
Lights will turn off 20 seconds
after no motion is detected
Set motion sensor sensitivity to
High. Detection range is up to
8m/26ft
Override sensor and manually
turn LED Light ON for 10
minutes. After 10 minutes, the
spotlight will automatically
revert to sensor mode
Battery
Compartment
Mounting Base
Knuckle Screw
Mounting Base
Thumb Screw
EnforcerTM Red & Blue
Flashing LED Lights
Motion/Light Sensor
The ambient light sensor prevents the
spotlight from activating during the
daytime to preserve battery power.
Keeping the LED Light on continuously for prolonged periods of time
will signiî´ªcantly shorten battery lifespan and reduce operating time.
Spotlight
Remote Control
3
BATTERY INSTALLATION
MOUNTING THE SPOTLIGHT
USING THE REMOTE CONTROL
• When aiming the remote control towards the spotlight, ensure that the distance is within 12m/40ft
and there is no obstruction between the remote control and the spotlight.
• When you press a button on the remote control, the spotlight will ash the red Enforcer LED light
once to conî´ªrm it has received the command.
• If you set both "Light on Motion" and "Enforcer on Motion" to OFF, the spotlight will power off for 1
hour. After 1 hour, the spotlight will automatically switch back to "Light on Motion" mode.
• To operate only Enforcer Lights on motion, perform these steps in the following order:
1. Press the "Light on Motion" ON button.
2. Press the "Enforcer on Motion" ON button.
3. Press the "Light on Motion" OFF button.
Spotlight
The spotlight requires four size D 1.5V batteries (not included). For reliable, long-lasting performance, use
only high quality alkaline or lithium batteries. To install batteries:
Remote Control
The remote control is powered by one CR2025 3V battery which comes pre-installed.
• To activate the battery, simply pull the plastic lm out from the bottom of the remote control.
• To replace the battery, push the tab on the left of the battery tray towards the right and pull out the
battery tray from the remote, as shown in the diagram on the back of the remote. Place one new
"CR2025" battery on the tray with the positive (+) side facing up. Insert the tray back into the remote.
1. Turn the front cover of the
spotlight counter-clockwise
to the unlock position , as
shown below, to release and
remove the cover.
1. Remove the mounting base from the stem by turning the thumb
screw A counter-clockwise.
2. Attach the mounting base to the mounting surface using the supplied
screws (if mounting on drywall/masonry, install wall anchors î´ªrst).
3. Insert the stem back into the mounting base and turn the thumbscrew
A clockwise until it is secured tightly.
4. To adjust the angle of the spotlight, loosen the knuckle screw B .
Aim the spotlight in the desired direction then tighten the
knuckle screw B to hold it in place.
3. Align the marks then turn
the front cover clockwise
to the lock position , as
shown below, to secure the
battery compartment.
2. Insert batteries according to
the polarity markings
(+ and -) indicated inside the
battery compartment.
B A

Product specificaties

Merk: Swann
Categorie: Niet gecategoriseerd
Model: SWALPH-B400RWPK1

Heb je hulp nodig?

Als je hulp nodig hebt met Swann SWALPH-B400RWPK1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Swann

Swann

Swann SWIFI-COREPRO3S3 Handleiding

31 Maart 2024
Swann

Swann SWIFI-CORESOL Handleiding

31 Maart 2024
Swann

Swann SWIFI-CORESOLPK4 Handleiding

31 Maart 2024
Swann

Swann SWALPH-B12003HRB Handleiding

28 Maart 2024
Swann

Swann SWALPH-B400RWPK1 Handleiding

28 Maart 2024
Swann

Swann Buddy Handleiding

2 Juli 2023
Swann

Swann SW351-WSA Handleiding

18 April 2023
Swann

Swann Solar Charging Panel Handleiding

9 April 2023
Swann

Swann SW351-KCG Handleiding

21 Maart 2023
Swann

Swann DVR8-2500 Handleiding

11 Februari 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Xblitz

Xblitz R8 Power Charge Handleiding

3 December 2024
Xblitz

Xblitz R4 Power Handleiding

3 December 2024
Franke

Franke Urban UBG 610-78 Handleiding

3 December 2024
Franke

Franke ANX211RHD Handleiding

3 December 2024
Franke

Franke ANX220 Handleiding

3 December 2024
Dell

Dell NX3330 Handleiding

3 December 2024
Dell

Dell PowerConnect B-DCX-4s Handleiding

3 December 2024
Hager

Hager AKB83000701 Handleiding

3 December 2024
Hager

Hager AKB81500402 Handleiding

3 December 2024
Hager

Hager AKBA1500401V Handleiding

3 December 2024