Supermicro AOC-USASLP-L8I Handleiding

Supermicro Controller AOC-USASLP-L8I

Lees hieronder de đź“– handleiding in het Nederlandse voor Supermicro AOC-USASLP-L8I (104 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/104
AOC-USASLP-L8i Add-on Card
User’s Manual
Revison 1.0
AOC-USASLP-L8i Add-on Card User’s Manual
ii
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The
vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no
commitment to update or to keep current the information in this manual, or to notify any person or
organization of the updates. Please Note: For the most up-to-date version of this manual, please see
our web site at www.supermicro.com.
Super Micro Computer, Inc. (“Supermicro”) reserves the right to make changes to the product described
in this manual at any time and without notice. This product, including software, if any, and documentation
may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or
machine without prior written consent.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE
THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,
SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF
REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,
SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara
County in the State of California, USA. The State of California, County of Santa Clara shall be the
exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not
exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instruction manual, may cause harmful interference with radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference,
in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning
applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further
details.
Manual Revison 1.0
Release Date: March 6, 2009
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy
any part of this document. Information in this document is subject to change without notice.
LSI, Integrated Mirroring, Integrated RAID, Integrated Striping, Fusion-MPT, and MegaRAID are
trademarks or registered trademarks of LSI Corporation. Other products and companies referred to herein
are trademarks or registered trademarks of their respective companies or mark holders.
Portions of this document © 2006-2007 LSI Corporation
Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS
PRODUCT MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER
REPRODUCTIVE HARM.
iii
Table of Contents
Chapter 1 Safety Guidelines .......................................................... 1-1
1-1 ESD Safety Guidelines..................................................................... 1-1
1-2 General Safety Guidelines............................................................... 1-1
1-3 An Important Note to Users ............................................................. 1-1
Chapter 2 Connectors, Jumpers and Indicators............... 2-1
2-1 Front Connectors and Pin Definitions ............................................ 2-1
Internal SAS Connectors ........................................................................ 2-1
I-Button ................................................................................................... 2-1
2-2 Front Jumper Locations and Pin Definitions ................................. 2-2
2-3 RAID Minimum Drive Requirements .............................................. 2-3
Chapter 3 RAID Modes, Firmware and Drivers................... 3-1
3-1 RAID Modes....................................................................................... 3-1
3-2 Getting Firmware Downloads.......................................................... 3-2
3-3 Flashing Firmware............................................................................. 3-2
3-4 Downloading RAID Mode Drivers...................................................3-2
3-5 Activating RAID Modes in OPROM BIOS .....................................3-3
Chapter 4 MegaRAID BIOS Configuration Utility.............. 4-1
4-1 Performing a Quick Configuration .................................................. 4-1
4-2 Configuring Arrays and Logical Drives .......................................... 4-1
Starting the MegaRAID BIOS CU ...........................................................4-2
Using Easy Configuration ....................................................................... 4-2
Using New Configuration and View/Add Configuration...........................4-5
Creating a Global Hotspare Drive ...........................................................4-6
Initializing Virtual Drives..........................................................................4-7
First Initialization Method .....................................................................4-7
Second Initialization Method ................................................................4-8
4-3 Setting the Hard Disk Write Cache and Read Ahead Policies... 4-9
4-4 Rebuilding a Drive........................................................................... 4-10
4-5 Hot Plug Support.............................................................................4-11
4-6 Checking Data Consistency ..........................................................4-11
4-7 Viewing and Changing Device Properties...................................4-12
Viewing and Changing Adapter Properties ...........................................4-13


Product specificaties

Merk: Supermicro
Categorie: Controller
Model: AOC-USASLP-L8I

Heb je hulp nodig?

Als je hulp nodig hebt met Supermicro AOC-USASLP-L8I stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Controller Supermicro

Handleiding Controller

Nieuwste handleidingen voor Controller