SkyRC SK-300046 Handleiding
SkyRC
Radiografisch bestuurbaar speelgoed
SK-300046
Lees hieronder de 📖 handleiding in het Nederlandse voor SkyRC SK-300046 (4 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
1. ESC Setting
Connect the Program Box as the diagram above, turn on the ESC and do as follows,
Press key to enter different programmable items, press and key to browse all
the options and press key to confirm your selection and then the screen will go back to main
programmable menu.
When the screen displays the programed item, you could press “ESC” key to main programmable menu
and start to program next item.
Note: The programmable items differs depends on 1/10th, 1/8th and 1/5th ESC. Concerning to screen
above, we take SkyRC Toro 1/10th 120A ESC(SK-300044) as example.
Sending to ESC
Please waiting..
Red power wire
(battery positive)
Battery
Pack
Black power wire
(battery negative)
Power
Switch
2 /6
SPECIFICATIONS
Input Voltage (ESC Setting): 6-10VDC
Input Current (ESC Setting): 500mA
Idle Current (ESC Setting): <20mA
Operating Temperature: 0-40ºC
Storage Temperature: -10 — 60 ºC
Operating Humidity: 10 - 90%RH
Storage Humidity: 20 - 75%RH
Protection Class: IP20
Dimension: 85x48.5x11.8mm
Weight: 40g
APPLIATION
There are four keys on the front panel,
: You could press this key to enter into the referred menu or confirm your selection.
And : You could press these two keys to go to previous page and to go to next page or
change the value of referred item.
: You could press this key to go back to previous menu.
ESC Setting
Battery Monitor ENTER Connecting ESC
Please waiting..
Running Mode
Motor Direction
ENTER
ESC
ENTER
Sending OK!
ENTER
ENTER
Forward/Brake*
Forward/Brake/R
ENTER
INSTRUCTION MANUAL
PROGBOX
Thank you for purchasing SkyRC Program Box (SK-300046). Please read this entire operating manual
completely and attentively as it contains important information. SkyRC Program Box is a very
sophisticated electronic device that controlled by high performance microprocessor.
With compact size and easy operation, SkyRC Program Box offers six-in-one functions:
INTRODUCTION
FUNCTION
SK-300046
1 / 6
ESC Setting: It can work as a Program Box, an individual device which can be used to programming
the ESC, and the option of each parameter is displayed on the LCD screen;
LiPo Battery Monitor: It can check the total cell number, total voltage, each cell voltage, highest voltage
and lowest voltage and the voltage difference between the highest voltage and lowest voltage.
Input PPM Signal Monitor: It can check the output voltage from the receiver and the receiver's PPM
signal width and frequency.
Servo Tester: It can check the input voltage, servo travel position and peak current.
Motor KV/RPM Tester: It can check the motor KV, RPM and input voltage.
It can also work as SkyLINK, an USB adaptor which can be used to link the ESC with a PC, and the
user can update the firmware of the ESC or programming the ESC by SkyLINK software on PC.
1.
2.
3.
4.
5.
Motor Sensor
USB to PC
I/O Connector
Escape Key
Down Key
Up Key
Enter Key
Battery Balance
Connector
LCD Screen
16Chr. X 2 Lines
1. ESC Setting
2. LiPo Battery Monitor
3. Input PPM Signal Monitor
4. Servo Tester
5. Motor KV/RPM Tester
6. PC Interface - Link ESC to PC
6.
3 / 6
3. PPM Monitor
It can check the output voltage from the receiver and the receiver's PPM signal width and frequency.
Connection
Connect the Program Box with the ESC, receiver as the diagram above, and turn on the ESC and the
transmitter.
Please note that the Program Box must be inserted in to the Throttle Channel and the ESC can be
inserted to any channel of the receiver as it is used to supply power to the receiver.
When it connects the battery, ESC, receiver, it could check the output voltage from the receiver and
the receiver's frequency and the neutral pulse position.
At this time, hold full throttle and hold full brake to check the receiver's PPM signal width.
4.17 4.18 4.17V
4.16 4.17 4.18V
MIN:4.16V
MAX:4.18V
Delta:0.02V
Total:25.03V
ESC Setting
Battery Monitor
Connect the Program Box and the battery as the diagram above, monitor battery voltage as follows,
2. Battery Monitor
It could check the total cell number, total voltage, each cell voltage, highest voltage and lowest
voltage and the voltage difference between the highest voltage and lowest voltage.
LiPo Battery Connection Diagram
4. Servo Tester
It can check the input voltage, servo travel position and peak current.
The default servo neutral position is 1520us/100Hz and 760us/100Hz. If the testing servo is not
1520us/100Hz and 760us/100Hz, please enter CUSTOM and set the servo neutral
position(range:200-2000us) and frequency(range: 50-200Hz) by yourself.
There are two kinds of mode (Swing Mode and Manual Mode) to make the servo swing and check
the servo travel position.
Swing Mode: it will send out a signal to make the servo swing automatically
Manual Mode: it allows you to change the PPM signal and check the servo's response to the signal.
Connection
4 / 6
V:6.03V F: 96Hz
PPM:1490us
Battery Monitor
PPM Monitor
V:6.01V F: 96Hz
PPM:2075us
V:6.01V F: 96Hz
PPM:1044us
Neutral Pulse Position
Lowest Pulse Position
Highest Pulse Position
ENTER
KV/RPM
Servo Tester
N:1499us
F:100Hz
Set [custom]
Set [1520us] ENTER
Set [1520us]
Set [760us] ENTER Set Swing Mode
Set Manual Mode
W [1499us] 0.00V
M>>1499us Pk0.0A
ENTER
W [1499us]00.00V
△100us Pk0 0A: .
W [1499us] 0.00V
M>>1499us Pk0.0A
Set Swing Mode
Set Manual Mode
W [1499us] 0.00V
M>>1499us Pk0.0A
ENTER
* Remark 1
* Remark 2
* Remark 3
Neutral
Pulse Position
Input
Voltage
Peak
Current
Current
Pulse Position
Changing Amplitude
of the Pulse Width
ENTER
ENTER
Manufactured by
SKYRC TECHNOLOGY CO LTD ., .
www skyrc com. .
RoHS
7504-0348-01
We guarantee this product to be free of manufacturing and assembly defects for a period of one year
from the time of purchase. The warranty only applies to material or operational defects, which are
present at the time of purchase. During that period, we will repair or replace free of service charge for
products deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any
damage or subsequent damage arising as a result of misuse, modification or as a result of failure to
observe the procedures outlined in this manual.
WARRANTY AND SERVICE
5 / 6 6 / 6
When you enter this screen, Press and to choose the right neutral pulse position
of the servo and enter to frequency setting. Press and to choose the right
frequency and enter swing/manual screen.
In the screen, press and to change the amplitude of the pulse width.
In this screen, press and to change the pulse width and check the response of
the servo to different pulse width.
* Remark 1
* Remark 2
* Remark 3
5. Motor KV/RPM Tester
It can check the motor KV, RPM and input voltage.
Connect the Program Box with ESC, receiver, motor, motor sensor cable and battery as the
diagram above, and turn on the ESC and set the pole number (range: 2, 4, 6, 8,...28.) of the
motor by pressing and key.
After you set the motor pole number, move the trigger to get the motor KV and when the trigger is
moved to full throttle, you can read the motor RPM valve from the screen.
PPM Monitor
KV/RPM ENTER KV 4000 Pole:2
RPM:33600 8.4V
KV 4000 Pole:6
RPM:33600 8.4V
KV 4000 Pole:6
RPM:33600 8.4V
6. PC Interface - Link ESC to PC
You could use it as SkyLink(SK-600013) to link the ESC with PC, and update the firmware of the
ESC or program the ESC by SkyLink software on PC.
Connect the Program Box as the diagram above, turn on the ESC and do as follows,
ESC Setting
Battery Monitor 简介
USB----PC USB
Connected to PC!
ENTER
When you see above screen, you could start to program the ESC in PC.
Note: Please click to check whether there is update version of the Program Box.
And if there is, you could click to update your Program Box.
Firmware Update
Update
To PC
Product specificaties
Merk: | SkyRC |
Categorie: | Radiografisch bestuurbaar speelgoed |
Model: | SK-300046 |
Kleur van het product: | Zwart |
Ingebouwd display: | Ja |
Gewicht: | 40 g |
Breedte: | 85 mm |
Diepte: | 48.5 mm |
Hoogte: | 11.8 mm |
Soort: | Radio-Controlled (RC) Model Accessories & Supplies |
Ondersteund aantal accu's/batterijen: | 1 |
Bedrijfstemperatuur (T-T): | 0 - 40 °C |
Relatieve vochtigheid in bedrijf (V-V): | 10 - 90 procent |
Type product: | Programmeringsbox |
Batterijtechnologie: | Lithium-Polymeer (LiPo) |
Type beeldscherm: | LCD |
Input voltage bereik: | 6 - 10 V |
Heb je hulp nodig?
Als je hulp nodig hebt met SkyRC SK-300046 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Radiografisch bestuurbaar speelgoed SkyRC
2 Juni 2023
1 Juni 2023
28 Mei 2023
21 Mei 2023
20 Mei 2023
20 Mei 2023
19 Mei 2023
15 Mei 2023
13 Mei 2023
11 Mei 2023
Handleiding Radiografisch bestuurbaar speelgoed
- Radiografisch bestuurbaar speelgoed Absima
- Radiografisch bestuurbaar speelgoed ACME
- Radiografisch bestuurbaar speelgoed Amewi
- Radiografisch bestuurbaar speelgoed Blade
- Radiografisch bestuurbaar speelgoed DJI
- Radiografisch bestuurbaar speelgoed Futaba
- Radiografisch bestuurbaar speelgoed Graupner
- Radiografisch bestuurbaar speelgoed Little Tikes
- Radiografisch bestuurbaar speelgoed Multiplex
- Radiografisch bestuurbaar speelgoed Parrot
- Radiografisch bestuurbaar speelgoed Proline
- Radiografisch bestuurbaar speelgoed Reely
- Radiografisch bestuurbaar speelgoed Revell
- Radiografisch bestuurbaar speelgoed Robbe
- Radiografisch bestuurbaar speelgoed SAB
- Radiografisch bestuurbaar speelgoed Spektrum
- Radiografisch bestuurbaar speelgoed TacTic
- Radiografisch bestuurbaar speelgoed Tamiya
- Radiografisch bestuurbaar speelgoed Velleman
- Radiografisch bestuurbaar speelgoed WLtoys
- Radiografisch bestuurbaar speelgoed JR
- Radiografisch bestuurbaar speelgoed Overmax
- Radiografisch bestuurbaar speelgoed Chicco
- Radiografisch bestuurbaar speelgoed Carrera
- Radiografisch bestuurbaar speelgoed Biltema
- Radiografisch bestuurbaar speelgoed Lenoxx
- Radiografisch bestuurbaar speelgoed Carson
- Radiografisch bestuurbaar speelgoed Ninco
- Radiografisch bestuurbaar speelgoed Traxxas
- Radiografisch bestuurbaar speelgoed ARRMA
- Radiografisch bestuurbaar speelgoed Spin Master
- Radiografisch bestuurbaar speelgoed ParkZone
- Radiografisch bestuurbaar speelgoed Hobbywing
- Radiografisch bestuurbaar speelgoed JETI
- Radiografisch bestuurbaar speelgoed LRP
- Radiografisch bestuurbaar speelgoed Ripmax
- Radiografisch bestuurbaar speelgoed Maverick
- Radiografisch bestuurbaar speelgoed Axial
- Radiografisch bestuurbaar speelgoed Hangar 9
- Radiografisch bestuurbaar speelgoed FMS
- Radiografisch bestuurbaar speelgoed E-flite
- Radiografisch bestuurbaar speelgoed Flyzone
- Radiografisch bestuurbaar speelgoed Losi
- Radiografisch bestuurbaar speelgoed XciteRC
- Radiografisch bestuurbaar speelgoed FrSky
- Radiografisch bestuurbaar speelgoed Force Engine
- Radiografisch bestuurbaar speelgoed Vaterra
- Radiografisch bestuurbaar speelgoed Jada
- Radiografisch bestuurbaar speelgoed HPI Racing
- Radiografisch bestuurbaar speelgoed Kyosho
- Radiografisch bestuurbaar speelgoed PowerBox Systems
- Radiografisch bestuurbaar speelgoed Hobby Zone
- Radiografisch bestuurbaar speelgoed RC4WD
- Radiografisch bestuurbaar speelgoed Sky Rider
- Radiografisch bestuurbaar speelgoed DF-Models
- Radiografisch bestuurbaar speelgoed ROCHOBBY
Nieuwste handleidingen voor Radiografisch bestuurbaar speelgoed
16 November 2024
6 November 2024
5 November 2024
30 September 2024
30 September 2024
30 September 2024
30 September 2024
24 September 2024
24 September 2024
24 September 2024