SIIG CE-MT0A12-S1 Handleiding

SIIG Wandsteun CE-MT0A12-S1

Lees hieronder de 📖 handleiding in het Nederlandse voor SIIG CE-MT0A12-S1 (8 pagina's) in de categorie Wandsteun. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

A B C D E F G

(x2) M6X60

bolt

(x2) M6 concrete

anchor

(x4) M6 small

washer

(x2) M6 large

washer

(x4) M4X12

screw

(x4) M5X12

screw

(x4) M6X12

screw

4mm Allen Key 6mm Allen Key

04-0553C

LCD TV/Monitor Tilting Mount - 10" to 26"

Hardware

Installation Instructions

Tools Required: Electronic stud finder, #2 Phillips head screw driver, drill, 1/8" drill bit (wood

stud installation), 3/8" masonry drill bit (concrete/brick wall installation).

Page 1

Figure 1 Figure 2

Step 1: Wall Plate Installation

Hold the wall plate (Figure 2) to the wall, use the two mounting holes to mark the

locations to be used for mounting the wall plate. Locate the holes directly into the

brick, block or concrete, never into the mortar between the blocks.

Pre-drill two holes to a depth of 2" using a 3/8" masonry drill bit at the positions you've

marked and insert one concrete anchor (B) into each hole.

Position the wall plate onto the wall again and insert the bolts (A) and washer (D) into

the anchor as shown (Figure 2) and tighten.

Use a high-quality electronic stud finder (commercially available) to locate dead center

of the wood stud and mark the location with a pencil.

Wood Stud Installation

Concrete/Brick Wall Installation

Attach the wall plate to the wall again and insert the bolts (A) and washers (D) into the

holes (Figure 1) and tighten.

Hold the wall plate (Figure 1) to the wall, use the two mounting holes to mark the

locations to be used for mounting the wall plate.

Take down the wall plate and drill two 2" deep holes, using a 1/8" drill bit at the

positions you've marked.

Page 2

Figure 3

Figure 4

Phillips

screw driver

Figure 5 Figure 6 Figure 7

Step 3: Final Installation

Step 2: Display Plate Installation

Hang the display plate onto the top of the

wall plate and slip it into the wall plate as

shown (Figure 4).

Tighten the safety screw on the side and

back using a Phillips head screw driver

and the supplied 4mm Allen Key (Figure 5

& Figure 6 respectively).

Place your TV screen down on a soft, flat surface, and locate the threaded mounting

points that are located on the back of the display.

According to the size of the display's hole, choose the corresponding screw (E/F/G)

and washer (C) and insert into the hole as shown (Figure 3) and tighten.

Adjust the tension of the joint using the

supplied 6mm Allen Key (Figure 7).

Page 3

Product specificaties

Merk:	SIIG
Categorie:	Wandsteun
Model:	CE-MT0A12-S1
Kleur van het product:	Zwart
Montagewijze:	Muur
Geschikt voor schermmaten:	10 - 26 "
Maximale gewichtscapaciteit:	15 kg
Paneelmontage-interface:	50 x 50, 75 x 75, 100 x 100 mm
Compatibiliteit:	LCD TV/monitor
Montage interface compatibiliteit (min):	50 x 50 mm
Montage interface compatibiliteit (max):	100 x 100 mm
Bereik kantelhoek:	-45 - 45 °