Pro-Lift W-1806 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Pro-Lift W-1806 (4 pagina's) in de categorie Compressor. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
5 in 1 Air Compressor
Operating Instructions and Parts Manual
SFA Companies, Inc.
10939 N. Pomona Ave.
Kansas City, MO 64153
Tel (816) 891-6390, Fax (816) 891-6599 Printed in China
W-1806-M0_072015
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey
all safety messages that follow this symbol to avoid possible injury or property damage
!
Model W-1806
2
SAFETY AND GENERAL INFORMATION
Save these instructions for future use. Study, understand
and follow all instructions before operating this device.
The owner and operator of this device shall have an
understanding of the product and safe operating procedures
before attempting to use. If any doubt exists as to the
safe and proper use of this product, remove from service
immediately. Instructions and safety materials shall be
conveyed in the operator’s native language before use of
this product is authorized.
Inspect before each use. Do not use if bent, broken, melted,
burned or otherwise damaged components are noted.
A compressor that is damaged in any way or operates
abnormally shall be removed from service immediately. This
unit is designed for intermittent use only. Operation beyond
it’s designed duty cycle may result in compressor and/or
vehicle damage. NEVER exceed rated pressure of the item
being inated. If rated pressure is exceeded, the item being
inated may burst.
• Study, understand and follow all instructions before operating this device.
• When using this air compressor, basic safety precautions should always be followed to reduce risk of re or electrical
shock.
• Do not exceed rated pressure of the item being inated.
• Do not leave device operating and unattended.
• If DC plug fuse is blown, only replace with fuse of identical rating.
• This device contains a DC motor and components which may arc during normal operation. This arcing may ignite
ammable gases. Do not operate in a ammable environment.
• Keep out of reach of children.
• The power cord on this product contains chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm. Wash hands after handling (California law requires this warning to be given to customers
in the State of California).
• Do not alter this product.
• Failure to heed these markings may result in personal injury and/or property damage.
! WARNING
PRODUCT DESCRIPTION
The Pro-Lift 4 in 1 Air Compressor is designed and engineered
to inate automotive and light truck tires to manufacturer’s
recommended pressure. It can also be used to inate and
deate low pressure inatables such as rafts, cushions and
sports balls. Refer to the vehicle’s owners manual or inatable
product owner’s manual before using the compressor.
HOW TO USE
A. FOR USE WITH HIGH PRESSURE INFLATABLE ITEMS
1. With thumb latch Quick Connector open, place securely
onto tire valve stem (Fig. 2).
2. Use thumb to close Quick Connector, ensuring that the
thumb latch is as far down as possible (Fig. 3).
3. Insert power cord plug-in into compressor. Insert power
cord into a suitable outlet or 12V DC source (Fig. 4).
Toggle air ON/OFF switch to ON position. Unit should
begin inating.
4. Toggle air ON/OFF switch to OFF once desire pressure
is acheived, disconnect Quick Connector and unplug the
compressor power cord.
Fused 12V
DC Plug
Deator Inlet
(Not Visible)
Low Pressure
Inator Outlet
Pressure
Gauge
ON/OFF Switch
Low Pressure
inator Adapters
Figure 1 - W-1806 Nomenclature
Quick Connect Adapters and
replacement tire stem parts
Power Cord
Power Cord
Plug-in
3
B. FOR USE WITH LOW PRESSURE INFLATABLES
1. To inate air mattresses, beach balls, life jackets, etc.,
remove low pressure inator and low pressure inator
adapters from storage compartment.
2. Connect low pressure inator adapters onto low pres-
sure inator/deator (labeled “INFLATION POINT”) on
side of compressor, and use to connect plastic air hose.
3. Insert power cord plug-in into the detached low pressure
inator.
4. Plug the compressor into the DC 12V outlet. Toggle air
ON/OFF switch to ON position. Unit should begin inat-
ing.
5. Inate to a pressure or level of rmness recommended
by the manufacturer. Toggle air ON/OFF switch to OFF
and check for desired îšżrmness or pressure as needed.
6. Remove the adapter from low pressure inator.
C. DEFLATING INFLATABLES
1. To deate air mattresses, beach balls, life jackets, etc.,
remove low pressure inator and low pressure inator
adapters from storage compartment.
2. Connect low pressure inator adapter onto low pressure
deator outlet in front of low pressure inator (labeled
“DEFLATION POINT”).
3. Insert the adapter into the appropriate receiver on the
item to be deated.
4. Insert power cord plug-in into the detached low pressure
inator.
5. Connect the 12V DC plug to a suitable power source and
toggle the ON/OFF switch to ON. Compressor should
begin deation.
6. When item is sufciently deated, toggle ON/OFF switch
to OFF.
7. Remove the adapter from low pressure inator.
Quick Connector
Adapters for Inflatables
Plastic air hose
inflator adapters
Sports Adapter
Hose
Figure 2 Figure 3
Figure 4
Figure 5
5. Use a tire gauge to check ination and adjust to desired
pressure as recommended by the vehicle and/or tire
manufacturer.
NOTICE: Always double check air pressure using a reli-
able pressure gauge.


Product specificaties

Merk: Pro-Lift
Categorie: Compressor
Model: W-1806

Heb je hulp nodig?

Als je hulp nodig hebt met Pro-Lift W-1806 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Compressor Pro-Lift

Handleiding Compressor

Nieuwste handleidingen voor Compressor