JETI JEX-MB Handleiding

JETI Radiografisch bestuurbaar speelgoed JEX-MB

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI JEX-MB (7 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

U MSER ANUAL

MBAR EX

By JETI model s.r.o. . 11. 14 14 20

User Manual MBar EX:

-2-

C ONTENTS

1. INTRODUCTION ...................................................................................................................................... 3

2. MAIN FEATURES .................................................................................................................................... 3

3. PLACEMENT OF MBAR EX SENSOR ................................................................................................. 3

4. CONNECTING THE MBAR EX SENSOR ............................................................................................ 4

5. SETTING VIA JETIB ......................................................................................................................... 5OX

5.1 T : .............................................................................................................................. 5 HE MBAR EX SENSOR MENU

6. SETUP VIA DC/DS TRANSMITTERS .................................................................................................. 6

7. WARRANTY .............................................................................................................................................. 7

8. MBAR EX MENU DISPLAYED ON THE JETIBOX LCD: ................................................................ 7

User Manual MBar EX:

-3-

1. Introduction

MBar EX is a sensor that measures high pressures of non-corrosive and unionized gases and liquids. The

sensor records the maximum and minimum measured values of pressure and temperature. Also, it is possible to

set alarm for a high pressure measurement pressure drop. The information from the sensor is transmitted an or a

to the user via Duplex system. The EX can be used for measuring pressure in containers with EX MBar

compressed air (retractable landing gear systems) or for controlling the oil pressure in hydraulic systems.

The Duplex system takes advantage of the 2.4GHz band for communication. This system not only EX

transmits control data to the model but also sends data from the model back to the transmitter. The telemetry

data collected during operation is shown as actual, measured values in real time. The values are shown either on

the LCD screen of a connected JETIBOX or on the display of JETI model DC/DS transmitters.

2. Main features

- Measurement of pressure and temperature.

- Possible sound alarm signaling of excessive pressure or pressure drop using a JETI Tx module (EU only) or

JETIBOX profi.

- Can be used as an Expander and to connect other sensors.

- Can detect logical voltage levels on up to two inputs (e.g. detection of securing the chassis).

- The device is compatible with EX Bus protocol, i.e. it is possible to be configured comfortably via a special

menu in DC/DS JETI model transmitters.

- Firmware updates.

Technical data

MBar EX

Dimensions of the extension

Dimensions

30x23x13mm

Weight

M suring accuracy of absolute ea

pressure

±2%

Resolution of measured pressure

0,1kPa

Measurement range

0÷1000kPa (150psi, 10bar)

Operating temperature

- 10÷85°C

Recommended supply voltage

3.5 ÷ 8.4V

Maximum supply voltage

16V

Consumption

15mA

Diameter of the extension

2mm

3. Placement of MBar EX sensor

The sensor should be mounted in the model to a hard surface to prevent accidental pulling out of cables or

pressure tubing. Properly protect the sensor against the transmission of vibrations, e.g. using double-sided

adhesive tape. Use pressure tubing properly sized for the required pressure.

Attention! The sensor itself is not mechanically suited for frequent pulling out of the tubing. It is strongly

recommended to have the tubing permanently connected to the sensor. If necessary, disconnect the tubing

further away from the sensor. Failure to do so may damage the sensor.

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	JEX-MB
Kleur van het product:	Zwart
Gewicht:	7 g
Breedte:	30 mm
Diepte:	23 mm
Hoogte:	13 mm
Soort:	Radio-Controlled (RC) Model Parts
Certificering:	CE
Spanning:	3.5 - 8.4 V
Type product:	Druksensor
Stroom (max.):	0.015 A