JETI TD1609S Handleiding

JETI Radiografisch bestuurbaar speelgoed TD1609S

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI TD1609S (7 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

Manual DITEX-Manager

Manual Soware DITEX-Manager

With this guide, we show you how the soware DITEX manager should be applied in individual servo

programming. The soware can be download from www.Ditex-Servo.com. For more informaon,

please visit www.Ditex-Servo.com, Hacker-Motor.com or our YouTube video channel.

To program a Ditex servo rst install the soware. For programming the servos the USB interface

(Hacker part number 87201006) is required.

Open the soware and connect the USB interface to your computer. The LED of the interface lights

up green when the connecon is successful. Thereaer, plug the servo to the interface and the so-

ware will open automacally. The servo conrms this with a tone sequence.

If you click the "queson mark" in the top left to open the main menu

of the soware, there are some basic sengs of the soware that can

be changed .

Here you can change the language.

In the Sound menu, the sound of the software can be changed or turned o

The design of the soware can be chosen to your own preferences

Here you can load the update to the currently connected servo.

When pressing this buon, the Manager is restored to the original state.

General informaon

Any changes that need to be performed on the servo-soware have to be conrmed by

Otherwise the sengs will be not saved in the servo!

Manual DITEX-Manager

SETUP

Adjusng the servo center posion .

Maximum travel A

Maximum travel B

max. Limit travel A

max. Limit travel B

Changing servo direcon

The mode "NARROW" is for specic applicaons that require a higher drive

frequency. For all other applicaons u the "NORMAL" mode. se

Adjust the servo-speed

Possibility of reducing the maximum servo-torque

The servo drives for the set me is with full torque, this allows a more sensi-

tive control to the zero posion.

Here you can choose how the servo on disconnuaon of the servo pulses

should behave by the receiver. This mode is only acve when an interrup-

on of the signal cable, or if the receiver is in acve fa -safe with no servo il

output pulses.

Servo-speed to the specied fail-safe posion.

Posion where the servo drives when signal loss. ,

Manual DITEX-Manager

Prevents a sudden start of the servos when turning on the model. The servos

drive the zero posion at set speed and force. We recommend to let the so

start acve, this conserves the servo, linkage and the model.

Here are the current posion of the servo is displayed in degrees.

This is a servo tester enables you to move the servo.

Also used to control the travel sengs that you

made.

This is a special feature for adjusng the center of a rudder. If you have

connected the servo to the linkage and the rudder, press the icon "DISEN-

GAGE". Now you can bring the rudder by hand in zero posion. Then press

the icon "ENGAGE" and the servo saves the current posion as the new

zero posion. Pressing the icon "SET NEUTRAL" always moves the servo to the programmed center

posion.

SECURITY

Here, the maximum internal power temperature is set at which the servo

outputs an audible warning and the power limit is enforced. This is a secu-

rity feature to the servo from overheang by example treacly / blocking a

linkage to protect. We recommend these values to change only in individual

cases or in special applicaons.

In fall below or exceed the adjusted voltages the servo will warn acous-

cally when you enable this feature in the sound monitor.

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	TD1609S
Kleur van het product:	Black, Red
Gewicht:	63 g
Breedte:	20 mm
Diepte:	37 mm
Hoogte:	40 mm
Soort:	Radio-Controlled (RC) Model Parts
Correct gebruik:	Universeel
Materiaal:	Metaal
Merkcompatibiliteit:	JETI
Aantal:	1
Spanning:	4.8 - 10 V
Type product:	Servo-
Type motor:	Kernloze motor
Programmeerbaar:	Ja
Frequentie microprocessor:	80 MHz
Koppel (@6 V):	11.3 kg/cm
Snelheid (@60°, 6 V):	0.111 s
Torsie (@ 7,4 V):	13.2 kg/cm
Snelheid (@60°, 7,4 V):	0.052 s