Elba ETM-E3690P Handleiding
Lees hieronder de π handleiding in het Nederlandse voor Elba ETM-E3690P (1 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
βBefore installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 CΛ Λ
-Water pressure between 0.05MPa β 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ο¬
water supply
βFlush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
βInspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
βUse thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting β
‘
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Product specificaties
| Merk: | Elba |
| Categorie: | Kraan |
| Model: | ETM-E3690P |
Heb je hulp nodig?
Als je hulp nodig hebt met Elba ETM-E3690P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kraan Elba
19 Augustus 2024
19 Augustus 2024
19 Augustus 2024
19 Augustus 2024
19 Augustus 2024
Handleiding Kraan
- Kraan IKEA
- Kraan Etna
- Kraan Inventum
- Kraan Brita
- Kraan Delta
- Kraan Ernesto
- Kraan Franke
- Kraan Grohe
- Kraan Hansgrohe
- Kraan Hotto
- Kraan KitchenAid
- Kraan Livarno
- Kraan Lynx
- Kraan Miomare
- Kraan Quooker
- Kraan Smeg
- Kraan Stiebel Eltron
- Kraan Teka
- Kraan Concept
- Kraan Blanco
- Kraan Caple
- Kraan CDA
- Kraan Curaqua
- Kraan SchΓΌtte
- Kraan Lamona
- Kraan Nodor
- Kraan Empire
- Kraan Brauer
- Kraan Elkay
- Kraan Oras
- Kraan Berg
- Kraan Mizzo
- Kraan ZLine
- Kraan Moen
- Kraan Mueller
- Kraan Aloni
- Kraan WillieJan
- Kraan Everpure
- Kraan Sani-Lav
- Kraan Fala
- Kraan Neo
- Kraan Lomazoo
- Kraan American Standard
- Kraan Livarno Lux
- Kraan Billi
- Kraan SaniSupreme
- Kraan Deante
- Kraan Omnires
- Kraan Vola
- Kraan Zip
- Kraan The Galley
- Kraan Viidako
- Kraan Waltec
- Kraan Gessi
- Kraan Puretec
- Kraan Sussex
- Kraan Fantini
- Kraan Oliveri
- Kraan Rogerseller
- Kraan Axor
- Kraan Graff
- Kraan Zurn
- Kraan Karran
- Kraan Symmons
- Kraan Jacuzzi
- Kraan Rohl
- Kraan ProFlo
Nieuwste handleidingen voor Kraan
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024