Sussex RWBMS150RH Handleiding

Sussex Kraan RWBMS150RH

Lees hieronder de 📖 handleiding in het Nederlandse voor Sussex RWBMS150RH (2 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
5.5
Licence No. 0124
In ac cord anc e with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterr ating.g ov.au
The mo re
stars the mo re
water efcient
1
NOGGIN
Finished
Wall Surface
56mm
Dress
Ring
Manifold
Apply Silicone
SET
SCREW
HANDLE
BODY
Stud Face
64
2
NOGGIN
Dress Ring
Masterfit
Stud Face
Finished
Wall Surface
Bath Outlet
Product code
Circa
RWBMS150RH Wall basin mixer system 150mm
RWBMS200RH Wall basin mixer system 200mm
RWBMS250RH Wall basin mixer system 250mm
RWBMS150RH-V Wall basin mixer system 150mm - Vertex
RWBMS200RH-V Wall basin mixer system 200mm - Vertex
RWBMS250RH-V Wall basin mixer system 250mm - Vertex
Wall basin mixer system Dress kit
Mixer dress kit
Outlet fit off
- Remove Mixer protective cover.
- Using silicone, seal the wall surface around the Mixer and
Outlet threads.
- Ft the Mixer Dress Ring.
- Fit the Handle Body onto the Mixer Cartridge Lever and ensure full engagement.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
- Apply sealing tape (Teflon) to male thread.
- Place Dress Ring over outlet.
- Push Dress Ring back to meet the wall.
- Fit and align the Outlet.
- To complete installation , operate the Mixer(s) checking the flow of both hot and cold water from the Outlet .
Check all fittings and fixtures for water leaks.
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
1
View f rom ab ove
Masterfit
NOGGING
Dress Ring
Handle
Body
1/2" BSP
Male Outlet 1
30-32mm
Wall Covering
Max. 30mm
90
70
Mixer
Stud face
Min.
8mm
This
side
UP
Outlet Hot
Cold
Mixer
Outlet
Pipe Connections
Product code
Circa
RWBMS150RH Wall basin mixer system 150mm
RWBMS200RH Wall basin mixer system 200mm
RWBMS250RH Wall basin mixer system 250mm
RWBMS150RH-V Wall basin mixer system 150mm - Vertex
RWBMS200RH-V Wall basin mixer system 200mm - Vertex
RWBMS250RH-V Wall basin mixer system 250mm - Vertex
Wall basin mixer system Rough in
Plumbers note
Rough in plumbing
Pipe connections
- Prior to installing calculate the finished wall thickness, maximum is 30mm thick. Contact manufacturer for
further options.
- If Wall thickness is greater than 30mm, contact manufacturer for further options.
- Prepare a Nogging to be fixed parallel between the Wall Studs.
- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.
- The Masterfit will be marked “This side Up” to indicate orientation.
- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Master fit is level and square.
- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)
- Do not remove any factory fitted pressure plugs or Fixings.
- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
- Check all fittings and fixtures for leaks.
- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
- Store the Dress Kit in a safe place until required (see Dress Finishing Guide).
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY )
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the
manufacturer’s warranty.
sussextaps.com.au


Product specificaties

Merk: Sussex
Categorie: Kraan
Model: RWBMS150RH

Heb je hulp nodig?

Als je hulp nodig hebt met Sussex RWBMS150RH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Kraan Sussex

Handleiding Kraan

Nieuwste handleidingen voor Kraan