Chef's Choice Manual 490 Handleiding
Chef's Choice
Messenslijper
Manual 490
Lees hieronder de 📖 handleiding in het Nederlandse voor Chef's Choice Manual 490 (8 pagina's) in de categorie Messenslijper. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
MOdel 490 instructiOns
Manual Scissor Sharpener
Read these instructions before use.
It is essential that you follow these
instructions to achieve optimum results.
© 2013 EdgeCraft Corp.
cHeF’scHOice
®
MAnuAl scissOr sHArPener
The Chef’sChoice
® Manual Scissor Sharpener Model 490 is designed to sharpen scis-
sors to professional standards, simply and easily. It can put an exceptionally sharp
edge on your kitchen, household, sewing, and arts and crafts scissors. There are sev-
eral distinctly different types of scissors, consequently, it is important to read this entire
booklet to optimize your sharpening results.
The Chef’sChoice® Model 490 Manual Scissor Sharpener owes much of its uniqueness
to its precision Angle Guides, designed to position the scissor blade securely at a pre-
cise angle against the diamond abrasive plates. Before sharpening your first scissors it
is important to read the following instructions carefully.
iMPOrtAnt inFOrMAtiOn
1. WARNING: EVEN THOUGH ALL SCISSORS MAY APPEAR TO BE SIMILAR, THERE ARE
MAJOR DIFFERENCES AMONG THEM THAT MUST BE UNDERSTOOD BEFORE YOU
USE THIS SHARPENER. THE MODEL 490 WILL SHARPEN MOST, BUT NOT ALL, TYPES
OF SCISSORS. DO NOT ATTEMPT TO SHARPEN HAIR STYLING SCISSORS, PINKING
SHEARS, MANICURE SCISSORS, SERRATED BLADES, TIN SNIPS, OR SCISSORS MORE
THAN 10” IN LENGTH.
The Chef’sChoice® Model 490 Scissor Sharpener will sharpen most other blades, includ-
ing knife-edge scissors, as described below. It is essential, however that you follow the
instructions to optimize your results.
2. It is not entirely obvious that the two blades on some scissors can be different. When you
cut with scissors, one blade the anvil blade, is designed to be below the material and the
other blade called, the cutter blade, is above the material. See Figures 1 and 2. Commonly
the blade on top of the material, the cutter blade, does most of the cutting. Referring to the
Figures 1 and 2, note that the cutter blade usually has the oblong finger-hold and a more
rounded tip. The anvil blade has a more pointed tip and a round finger hold.
3. It is very important to be able to identify the special knife-edge type scissors. They
have a cutter blade that is factory sharpened at a very small angle to form a knife-like
edge that is extremely sharp. THE KNIFE-EDGE CUTTER BLADE MUST BE SHARPENED
ONLY WITH THE WHITE KNIFE-EDGE ANGLE GUIDE SUPPLIED WITH EACH SHARP-
ENER. With this type scissor, the knife-edge cutter blade does virtually all the cutting.
Commonly only the cutter blade of this
type scissor has the knife edge. When
that is the case and you can properly
identify and sharpen that blade, sharpen-
ing the other (anvil). Only the knife-edge
scissor blade should be sharpened by
the special procedure on page 7. If you
elect to sharpen the anvil blade, use
the sharpening procedure for standard
scissors described in page 5. Do not
confuse these blades. If you have any
doubt about whether you have this type
of scissors, ask your nearest fabric or Figure 1. Typical right-handed scissors.
2
sewing center to help you identify these special blades before you sharpen them. (Most
lower cost and general purpose scissors are not knife edge scissors).
4. During the sharpening process you will need to know how to feel for a burr on the scissor
blade in order to know when sharpening is complete. Feeling for a burr involves running
your finger carefully across (NOT ALONG) the back of the blade as shown in Figure 3. A
burr is a microscopic protrusion of metal produced during the sharpening process under
the edges of the blade which can be felt but is not always visible. It will feel rough and
jagged compared to the smooth finish on the back of the blade.
5. The Manual Scissor Sharpener Model 490 will sharpen either right hand or left hand
scissors without need to disassemble them. If you are left handed you probably have
purchased left hand scissors.* To sharpen right hand scissors, hold the wider, handle
portion of the sharpener in your left hand. With left hand scissors, hold the sharpener in
your right hand (see Figures 5 and 6). However, the orientation of the angle guide on the
sharpener will remain the same with either right or left handed scissors.
6. Before sharpening identify the type of scissor you have. Unless you have scissors designed
for specialized applications, you will have either; (a) standard right handed scissors; (b) stan-
dard left handed scissors; or (c) knife edge scissors (which can be either right or left handed).
By far the most popular scissor is standard right handed. Follow the appropriate instructions
below depending on the type of scissors you have.
*You can determine whether your scissors are right or left handed as follows: Open the
scissors and lay them on a table. If the cutting edge of the top blade faces to your right, the
scissors are right-handed. If the cutting edge of the top blade faces your left, the scissors
are left-handed.
GettinG tO KnOW tHe cHeF’scHOice
MOdel 490 sHArPener
The Chef’sChoice® Model 490 Scissor Sharpener is designed to sharpen the most
popular general purpose scissors and those commonly used for sewing and crafts.
The Model 490, See Figure 4, consists of the Sharpener, two (2) diamond coated
abrasive pads, and three (3) Angle Guides.
Figure 3. Carefully feel for a burr along
the entire back of the blade. Note arrow
for direction of finger movement when
in contact with blade.
Figure 2. Typical position of the
Cutter Blade and Anvil Blade on
right-handed scissors.
3
Product specificaties
| Merk: | Chef's Choice |
| Categorie: | Messenslijper |
| Model: | Manual 490 |
Heb je hulp nodig?
Als je hulp nodig hebt met Chef's Choice Manual 490 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Messenslijper Chef's Choice
8 Januari 2024
8 Januari 2024
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
Handleiding Messenslijper
- Messenslijper IKEA
- Messenslijper Krups
- Messenslijper Adler
- Messenslijper Ambiano
- Messenslijper Bartscher
- Messenslijper Bavaria
- Messenslijper Beper
- Messenslijper Berkel
- Messenslijper Bifinett
- Messenslijper Blokker
- Messenslijper Bomann
- Messenslijper Domo
- Messenslijper EdgeCraft
- Messenslijper Einhell
- Messenslijper Fagor
- Messenslijper Gardenline
- Messenslijper Gastroback
- Messenslijper Gourmetmaxx
- Messenslijper Graef
- Messenslijper Gude
- Messenslijper Melissa
- Messenslijper Powerplus
- Messenslijper Presto
- Messenslijper Princess
- Messenslijper Roadstar
- Messenslijper Salter
- Messenslijper Silvercrest
- Messenslijper Sogo
- Messenslijper Steba
- Messenslijper Studio
- Messenslijper Tower
- Messenslijper Trebs
- Messenslijper Ozito
- Messenslijper Clatronic
- Messenslijper Guzzanti
- Messenslijper OBH Nordica
- Messenslijper Orbegozo
- Messenslijper Tacklife
- Messenslijper Eldom
- Messenslijper Waring Commercial
- Messenslijper Brentwood
- Messenslijper Herkules
- Messenslijper Genie
- Messenslijper C3
- Messenslijper Orava
- Messenslijper Alpha Tools
- Messenslijper For_Q
- Messenslijper Wüsthof
- Messenslijper Work Sharp
- Messenslijper Petra Electric
- Messenslijper GARDE
- Messenslijper IdeenWelt
- Messenslijper Donau Elektronik
- Messenslijper Sharpal
Nieuwste handleidingen voor Messenslijper
5 December 2024
4 December 2024
4 December 2024
17 November 2024
17 November 2024
16 November 2024
5 September 2024
15 Augustus 2024
15 Augustus 2024
15 Augustus 2024