Chapin 63900 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Chapin 63900 (40 pagina's) in de categorie Verfspuit. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/40
Model 63900 • 4G/ 15L
011944-1 R0314
Carefully Read These Instructions Before Use
WARNING
Use and Care Manual
DO NOT RETURN THIS
SPRAYER TO STORE
Call: 1-800-950-4458
www.chapinmfg.com
Duty SprayerDuty Sprayer
CommercialCommercial
Chapin International, Inc
P.O. Box 549
700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458
www.chapinmfg.com
WARNING
WARNING: Handling the brass parts of this product will expose you to lead, a chemical
known to the State of California to cause birth defects and other reproductive harm.
Wash hands after handling.
CAUTION
1E
WARNING: Improper use or failure to follow instructions can result in explosive
failure causing serious eye or other injury. For safe use of this product you must read
and follow all instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause
pressure build-up resulting in possible explosion. Do not store or leave solution in tank after
use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when
spraying. Never use any tool to remove pump if there is pressure in the pressure chamber.
Never pressurize sprayer by any means other than the original pump. Do not attempt to
modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray
ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or
heat, pressure, or gas producing chemicals. Always read and follow chemical
manufacturer’s instructions before use with this sprayer as some chemicals may
be hazardous when used with this sprayer.
SK 1158-1
• PRE-USE CHECK: Before each use check tightness of hose nut to be sure hose is
securely attached to the shut-off assembly. Insure hose is securely attached to the
tank by tightening hose clamp if necessary. Insure that all nozzle and wand
connections are tight. Insure the large pump clamp is tight. Insure the 2 bolts
used to attach the pump lever to the pump shaft are tight.
• Do Not exceed a tank solution temperature of 120º F/ 49º C.
NOTE: The tank and hose may have residual water in it due to quality testing
performed on the sprayer.
1. Poly
Nozzle Cap
2. Retaining
Nut
3. Nozzle
Body
4. Nozzle
Gasket
5. Elbow
Figure 3Figure 2Figure 1
1. Brass
Nozzle Cap
2. Retaining
Nut
3. Nozzle
Body
4. Nozzle
Gasket
5. Elbow
Nozzle
Gasket
Retaining Nut
Elbow
Fan Nozzle Tip
2E
APPLICATIONS & USE FOR YOUR SPRAYER
Avoid using a sprayer for general cleaning purposes if plant protection or herbicide chemicals have already
been used in the sprayer. If a sprayer has been used for plant protection or as an herbicide,
clean the sprayer completely (see cleaning section) before using.
Plant Food: Use different spray patterns for optimum foliage feeding or for fungicide and pesticide
application.
Herbicides: Reduce weeds and unwanted plants but avoid using the same sprayer for plant feeding or
protection without thoroughly cleaning (see cleaning section) the sprayer first.
General Household Use: Apply detergents, cleaning solutions, warm water (do not exceed 120°F/49°C) or
nontoxic household cleaning chemicals for carpets, floors, walls, glass, counter tops and ceilings. DO NOT use
sprayer that has been used with herbicides, pesticides or other toxic chemicals for household applications.
General Outdoor Use: Use the sprayer for cleaning windows or with a detergent for general purpose
cleaning.
SPRAYER COMPONENTS & USE INFORMATION
NOZZLE ASSEMBLY
Figure 1-2
Unscrew the nozzle cap . Unscrew the (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5)
retaining nut (2). Push the nozzle body (3) (4) (2) with the nozzle gasket out of the retaining nut . To reinstall the nozzle,
reverse the above instructions.
Figure 3
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the
nozzle, reverse the above instructions.
WAND ASSEMBLY
1. Make sure the o-ring is installed on the end of the wand.
Insert the wand into shut-off valve.
2. Turn and tighten the retaining nut clock-wise onto the shut-off valve.
Retaining
Nut Wand O-ring Shut-off
Valve
Product specificaties
| Merk: | Chapin |
| Categorie: | Verfspuit |
| Model: | 63900 |
Heb je hulp nodig?
Als je hulp nodig hebt met Chapin 63900 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verfspuit Chapin
24 Juni 2023
20 Juni 2023
18 Juni 2023
18 Juni 2023
12 Juni 2023
11 Juni 2023
8 Juni 2023
4 Juni 2023
3 Juni 2023
26 Mei 2023
Handleiding Verfspuit
- Verfspuit Bort
- Verfspuit Deco
- Verfspuit Defort
- Verfspuit Easymaxx
- Verfspuit Einhell
- Verfspuit Elektra Beckum
- Verfspuit Ferm
- Verfspuit Holzmann
- Verfspuit Magnum
- Verfspuit Metabo
- Verfspuit Paintmaxx
- Verfspuit Parkside
- Verfspuit Pattfield
- Verfspuit Powerplus
- Verfspuit Silverline
- Verfspuit Wagner
- Verfspuit Westfalia
- Verfspuit Worx
- Verfspuit Jocca
- Verfspuit Ozito
- Verfspuit 3M
- Verfspuit Black And Decker
- Verfspuit Cocraft
- Verfspuit Meec Tools
- Verfspuit Aerotec
- Verfspuit Cotech
- Verfspuit Power Craft
- Verfspuit Truper
- Verfspuit Fieldmann
- Verfspuit Sun Joe
- Verfspuit Probuilder
- Verfspuit MSW
- Verfspuit Birchmeier
- Verfspuit Yato
- Verfspuit Aqua Joe
- Verfspuit Abac
- Verfspuit Meister Craft
- Verfspuit Wagner SprayTech
- Verfspuit XU1
Nieuwste handleidingen voor Verfspuit
16 November 2024
16 November 2024
15 November 2024
5 November 2024
15 Oktober 2024
15 Oktober 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024