Yamaha DTX920K Handleiding

Yamaha Muziekinstrument DTX920K

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha DTX920K (2 pagina's) in de categorie Muziekinstrument. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

This manual describes the standard assembly procedure for the DTX760K/DTX920K electronic drum kits. It covers assembly and wiring of the kit as shown below.

When you have completed all of the steps described, you will be ready to turn on the drum trigger module and start playing.

Illustrations show the DTX700 drum trigger module.

ELECTRONIC DRUM KIT

DTX760K/DTX920K Assembly Manual

• For assembly, you will require four individual packages – an RS700

Rack System, a DTP903 Pad Set, a DTP904 Pad Set, and a DTX700/

DTX900M Drum Trigger Module.

• This manual describes the process of assembling a drum-pad set and

drum trigger module to an already assembled RS700 Electronic Drum

Rack. Before starting the steps below, therefore, be sure to assemble

your RS700 as described in the Owner’s Manual that came with it.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, you can place cardboard from the drum kit packaging or the

like on the floor to prevent it from being scratched. This is particularly

important when using the HS740A Hi-hat Stand and KP100 Kick Pad.

IMPORTANT

NOTICE

Example of standard assembly

PCY155

(Cymbal Pad)

PCY135

(Cymbal Pad)

CH750

(Cymbal Holder)

RHH135

(Real Hi-hat Pad)

DTX700/DTX900M

Drum Trigger Module

HS740A

(Hi-hat Stand)

XP100T

(Tom Pad)

XP120SD

(Snare Pad)

SS662

(Snare Stand)

CH750

(Cymbal Holder)

PCY135

(Cymbal Pad)

CH755

(Cymbal Holder)

XP120T

(Tom Pad)

KP100

(Kick Pad)

RS700

(Rack System)

The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy

of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions disp these precautions layed together with

are extremely important in terms of ensuring safety, and therefore, they should be fully observed.

* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.

* Be sure to also read the Assembly Manuals and/or Owner’s Manuals that came with your pads and rack.

NOTICE: Usage Precautions

• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,

avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid

these precautions can lead to cable breakage and disconnection.

• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-

caution can result in malfunction.

• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to

a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).

Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.

• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances

can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or

wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away

using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the

detergent solution using a cloth soaked in water and tightly wrung.

Safety Precautions Please read carefully before proceeding.

Failure to observe the precautions described below can result in se-

rious injury or even death.

• Young children using this electronic drum kit should be supervised by a guardian to eliminate any

possibility of injury.

• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should

take special care whenever handling these components.

• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-

fore, you should take special care whenever handling these components.

• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In

addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads

may fall off or the rack may collapse or fall over, possibly causing injury.

• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe

surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.

• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If

someone were to trip on a cable, the kit could topple over and cause injury.

• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to

observe this precaution can result in injury or malfunction.

• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.

WARNING

Failure to observe the precautions described below can result in in-

jury and/or property damage.

• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during

this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by

sharp tips if these components are not handled carefully.

• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.

• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to

break and the drums to fall off, which in turn could lead to injury.

CAUTION

Manual Development Department

Published 10/2015 POTO*.*-**A0

Printed in Japan

ZT57980

Assemble the RS700 Electronic Drum Rack.

For instructions on how to assemble the RS700 Electronic Drum Rack, refer to the Owner’s Manual that came with it.

Open the boxes to reveal their contents.

Assemble the pads and the drum trigger module to the electronic drum rack.

Package 1: DTP903 Package 2: DTP904

PCY135

Cymbal Pad (x2)

PCY155

Cymbal Pad (x1)

RHH135

Real Hi-hat Pad (x1)

Stand base for the

RHH135 (x1)

CH750

Cymbal Holder (x2)

CH755

Cymbal Holder (x1)

HS740A

Hi-hat Stand (x1)

Hi-hat clutch for the

RHH135 (x1)

Cable band for the

RHH135 (x1)

Stoppers for the

PCY135 and

PCY155 (x3)

 2.5m stereo phone cables (x4) 4m stereo phone cables (x6)

Felts for the

PCY135 and

PCY155 (x3)

Cable bands (x10)Tuning key (x1)KP100 Owner’s Manual (x1)

PCY100/PCY135/PCY155 Owner’s Manual (x1)

RHH135 Owner’s Manual (x1)

XP120SD

Snare Pad (x1)

XP100T

Tom Pad (x2)

XP120T

Tom Pad (x1)

Clamp bolts (x3)

KP100

Kick Pad (x1)

SS662

Snare Stand (x1)

XP100T/100SD/120T/120SD Owner’s Manual (x1)

Assembly Manual (this pamphlet)

Package 3: DTX700/DTX900M

DTX700/DTX900M

Drum Trigger Module (x1)

 Module holder (x1) Module holder screw

(x4)

AC power adaptor* (x1)

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

DTX700/DTX900M Owner’s Manual (x1)

DTX700/DTX900M Data List (x1)

Assembling the cymbal holders Assembling the tom pads

1. Assemble the cymbal holders (CH750 x 2, CH755 x 1) on the electronic

drum rack as shown below.

CH750

CH755

1. Attach the clamp bolt to each of the tom pads and pro-

visionally tighten (by 5 or 6 turns).

2. Push the tom pads onto the rack’s clamp rods. Ensure

that the rod section is fully inserted into the each pad’s

mounting hole, and then tighten the clamp bolt to se-

cure the pad in place.

3. Loosen clamp bolts A to E as shown below to adjust

the height and angle of any of the pads. When correct-

ly positioned, be sure to securely retighten the bolts

before proceeding to the next step.

XP100T

XP120T

Tom pad (rear side)

Clamp bolt (tighten in the

direction of the arrow)

Tom pad

Rod section Clamp rod

Insert

Clamp bolt

Clamp bolt B

Clamp bolt D

Clamp bolt E

Clamp bolt A

Clamp bolt C

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time

without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Continued on other side

Assembling the drum trigger module and cymbal pads

Assembling the drum trigger module

1. Secure the module holder

to the bottom of the drum

trigger module using the

module holder screws.

2. Push the module holder into the holder clamp and tighten the

clamp bolt to secure it in place.

Assembling the cymbal pads

1. Using a tuning key, loosen the stopper’s key bolt.

2. Remove the wing nut, the two felt pads, and the bolt cover

from the cymbal holder.

3. Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in Step 1

above, it may not be possible to pass the stopper over the

cymbal holder’s shaft. In such a case, loosen the key bolt

as much as possible without removing it.

4. Replace the bolt cover.

* Turn the bolt cover to tighten it onto the threaded section

and firmly secure it in place.

5. With the stopper making full contact with the bottom surface

of the bolt cover as shown below, tighten the stopper’s key

bolt using the tuning key.

6. Place one of the felt pads removed in Step 2 on the cymbal

holder.

7. Mount the pad on the cymbal stand. Lower the pad into place

with the cymbal holder’s shaft passing through the central

hole. When mounted, the stopper’s pin should rest inside the

pad’s smaller hole.

* If you were to play your cymbal pad without the stopper’s

pin positioned well inside the smaller hole, the pad could

rotate, causing the pin to be pulled out. It is very important,

therefore, to ensure that the stopper is secured as shown

in Step 5 above.

8. Assemble the felt pad that came with the cymbal pad.

* The second felt pad removed from the cymbal holder in

Step 2 above is not required for assembly of your pad unit.

9. Tighten the wing nut to secure the pad unit to the cymbal

holder.

A cymbal pad’s built-in sensor is located close to the Yamaha

logo found on the top surface. In order to achieve the best per-

formance from your pad, position it such that the area around

the logo can be easily struck. (See the figure above.)

PCY135

PCY155PCY135

Drum trigger module

Module holder

screws

Module holder

Drum trigger

module (back

side)

Front of module

Drum trigger module

module holder

Clamp bolt

Holder clamp

Insert

Key bolt

Tuning key

Stopper

Wing nut

Felt pads

Bolt cover

Cymbal holder

Bolt cover

Threaded section

Stopper

Cymbal holder

Bolt cover

Cymbal holder

Stopper

Full contact

Felt pad that came

with pad unit Pad unit

Stopper’s pin

Felt pad

Smaller hole

Wing nut

Stopper

Cymbal holder

Pad unit

Bolt cover

Assembling the hi-hat stand

1. If a drum mat (sold separately) is not available, lay a sheet of

cardboard on the floor to protect it from being scratched.

2. Loosen the hi-hat stand’s wing bolt (a in the following figure).

3. Open up the three legs as shown below and then retighten

the wing bolt a to lock them in place.

4. Insert the footboard stabilizer rod into the frame hole as

shown below.

5. As shown on the right, loosen the hi-hat clutch’s wing bolt b

and remove the hi-hat clutch.

* The hi-hat clutch is not required when assembling the

electronic drum kit in the standard fashion described in

this manual. Instead, the hi-hat clutch that came with the

RHH135 Real Hi-Hat Pad will be used.

6. Remove the hi-hat shaft from the upper tube .

7. Insert the hi-hat shaft from Step 6 as far as it will go into

the lower tube and screw in the tip.

8. Insert the upper tube over the hi-hat shaft and tighten

the wing bolt c to secure it in place with the cymbal support

plate approximately half way between the top of the lower

tube and the top of the hi-hat shaft .

9. Remove the felt pad and the support plate attached above

the cymbal support plate. It is not required when assembling

the electronic drum kit in the standard fashion described in

this manual.

10. Assemble the RHH135 Real Hi-hat Pad.

* For detailed instructions, refer to the Setting Up section

in the RHH135 Owner’s Manual.

Wing bolt a

Footboard

stabilizer rod

Footboard

stabilizer rod

Felt washer

Support

plate

Cymbal

support plate

Hi-Hat clutch

Cymbal

support

plate

Assembling the kick pad

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from being scratched.

2. Remove the two wing bolts, spring washers, and flat washers from the kick pad frame, and line up each set nearby

in the order of removal.

3. Join the base section to the frame as shown below, and then secure it in place by assembling the wing bolts, spring

washers, and flat washers removed in the previous step from the base side.

Frame

Base

Flat washerSpring washer

Wing bolt

Assembling the Snare Stand and Snare Pad

1. Open up the snare stand’s legs and stand it up on the floor.

2. Open up the snare stand’s basket section, lay the XP120SD Snare Pad on it,

adjust the basket, and then tighten the adjusting knob to secure the pad and

prevent it from moving.

Adjusting

knob

Legs

XP120SD

(Snare pad)

Basket

Arrange the hi-hat stand, the kick pad, and the snare stand as shown in Example of standard assembly on the other side of this sheet.

• Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place cardboard from the drum

kit packaging or the like on the floor to prevent it from being scratched.

• If the kick pad comes into contact with the electronic drum rack’s center strut, raise the center strut.

Connect the pads to the drum trigger module.

As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.

Connect the drum trigger module to a power supply.

Setting up the drum trigger module.

NOTICE

1. As shown at right, connect the pads with the trigger input jacks (SNARE – KICK and HI-HAT CON-

TROL jack) of the drum trigger module by using the stereo phone cables.

• Insert the straight plugs of the cable into the trigger input jacks of the drum trigger module, then insert

the L-shaped plugs of the cables into each corresponding pad.

2. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being

pulled out.

Excessive bending can damage the pad cables. Ensure, therefore, that these ca-

bles are not bent at an extreme angle when wrapped around the clips.

Pads DTX700 jack names DTX900M jack names

SNARE q SNARE q SNARE

TOM1 w TOM1 w TOM1

TOM2 e TOM2 e TOM2

TOM3 r TOM3 r TOM3 or t TOM4

RIDE t y RIDE RIDE

CRASH y CRASH1 u CRASH1

CRASH2 u CRASH2 i CRASH2

HI HAT i HI HAT HI HATo

HH CON HI-HAT CONTROL HI-HAT CONTROL

KICK o KICK/!0 !0 KICK/!1

NOTICE

HH CON

TOM2

TOM3

KICK

TOM1

RIDE

SNARE

CRASH

HI HAT

CRASH2

[Locations of pad jacks]

1. Insert the power adaptor’s DC plug into the connector. Hook the power adaptor’s cord around

the cord clip to secure it in place.

2. Using the cable bands, secure the cables to the electronic drum rack at the positions circled in the fig-

ure on the right. ( )

3. Plug the AC power adaptor into an AC wall socket.

[Drum trigger module’s rear panel]

Cord clip

connector

[For DTX760K Owners]

Select the “DTX760K” trigger setup on the DTX700 drum trigger module. (For details on the trigger

setup procedure, see “Selecting a Sensitivity for the Entire Kit” from the DTX700 Owner’s Manual.)

If “DTX760K” is not displayed on the selection screen, please upgrade your DTX700’s firmware ver-

sion. Visit the following web page for information on the latest DTX700 firmware version and to

download firmware version upgrades.

http://download.yamaha.com/

If you would prefer not to upgrade your firmware version, select the “DTX750K” trigger setup, and

then make the following adjustments.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

• Pad type change for tom pads 1 to 3:

Select “XP120/100 Tom” as the DTX700 pad type. For details, refer to “For pad-related trigger set-

tings (TRIGGER/PAD/PAD TYPE 1/6)” from the DTX700 Reference Manual (pdf).

[For DTX920K Owners]

Select the “DTX920K” trigger setup on the DTX900M drum trigger module. (For details on the trigger

setup procedure, see “Selecting the Trigger Setup” from the DTX900M Owner’s Manual.)

If “DTX920K” is not displayed on the selection screen, please upgrade your DTX900M’s firmware

version. Visit the following web page for information on the latest DTX900M firmware version and

to download firmware version upgrades.

http://download.yamaha.com/

If you would prefer not to upgrade your firmware version, select the “DTX950K/900K” trigger setup,

and then make the following adjustment.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

Your electronic drum kit is now ready. * For instructions on turning on the drum trigger module, producing sounds, and other subsequent steps,

please refer to the Owner’s Manual that came with the module.

Product specificaties

Merk:	Yamaha
Categorie:	Muziekinstrument
Model:	DTX920K
Soort:	Drumsysteem
Soundeffects:	Chorus, Reverberation
Maximum polyfonie (noten):	64
Bit rate:	16 Bit
Aantal stuks:	5 stuk(s)
Kick-pedaal:	Ja
Soundmodule inbegrepen:	Ja
Hi-hat bekken:	Ja
Hihat-pedaal:	Ja
Aantal drumsets:	50