Yamaha DTX720K Handleiding

Yamaha Muziekinstrument DTX720K

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha DTX720K (2 pagina's) in de categorie Muziekinstrument. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

This manual describes the standard assembly procedure for the DTX582K/DTX720K electronic drum kits. It covers assembly and wiring of the kit as shown below.

When you have completed all of the steps described, you will be ready to turn on the drum trigger module and start playing.

Illustrations show the DTX502 drum trigger module.

ELECTRONIC DRUM KIT

DTX582K/DTX720K Assembly Manual

This manual describes the process of assembling a drum-pad set and drum trigger module to an already assembled RS502

Electronic Drum Rack. Before starting the steps below, therefore, be sure to assemble your RS502 as described in the Owner’s

Manual that came with it.

IMPORTANT

Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can

place cardboard from the drum kit packaging or the like on the floor to prevent it from being

scratched. This is particularly important when using the HS650A Hi-hat Stand and KP100

Kick Pad.

NOTE

If using double foot pedals and want to position them relatively far apart from one another,

please setup as shown below.

NOTICE

Example of standard assembly

Cymbal pad

Tom pad

Tom pads

Kick pad

Snare pad

Hi-hat stand

DTX502/DTX700

Drum trigger module

Real Hi-hat Pad

Electronic drum rack

Cymbal pad

The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy

of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions disp these precautions layed together with

are extremely important in terms of ensuring safety, and therefore, they should be fully observed.

* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.

* Be sure to also read the Assembly Manuals and/or Owner’s Manuals that came with your pads and rack.

NOTICE: Usage Precautions

• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,

avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid

these precautions can lead to cable breakage and disconnection.

• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-

caution can result in malfunction.

• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to

a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).

Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.

• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances

can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or

wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away

using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the

detergent solution using a cloth soaked in water and tightly wrung.

Safety Precautions Please read carefully before proceeding.

Failure to observe the precautions described below can result in se-

rious injury or even death.

• Young children using this electronic drum kit should be supervised by a guardian to eliminate any

possibility of injury.

• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should

take special care whenever handling these components.

• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-

fore, you should take special care whenever handling these components.

• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In

addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads

may fall off or the rack may collapse or fall over, possibly causing injury.

• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe

surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.

• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If

someone were to trip on a cable, the kit could topple over and cause injury.

• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to

observe this precaution can result in injury or malfunction.

• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.

WARNING

Failure to observe the precautions described below can result in in-

jury and/or property damage.

• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during

this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by

sharp tips if these components are not handled carefully.

• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.

• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to

break and the drums to fall off, which in turn could lead to injury.

CAUTION

Manual Development Department

Published 12/2015 POAP*.*-**A0

Printed in Vietnam

ZU86750

Open the boxes to reveal their contents.

After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.

Assemble the RS502 Electronic Drum Rack.

For instructions on how to assemble the RS502 Electronic Drum Rack, refer to the Owner’s Manual that came with it.

Assemble the pads and the drum trigger module to the electronic drum rack.

Components of DTX582K/DTX720K

XP80 Snare Pad

(x1)

PCY135 Cymbal

Pad (x2)

RHH135 Real

Hi-Hat Pad (x1)

Stand base for

RHH135 (x1)

RS502 Electronic Drum Rack (x1)

RS502 Owner’s Manual (x1)

HS650A Hi-hat

Stand (x1)

KP100 Kick Pad (x1)

Nine-channel snake cable (x1)

Stopper for

PCY135 (x2)

Cable band

(x6)

Cable band for

RHH135 (x1)

Felt pad for

PCY135 (x2)

DTX582K/DTX720K Assembly Manual (this booklet; x1)

PCY100/135/155 Owner’s Manual (x1)

RHH135 Owner’s Manual (x1)

XP70/80 Owner’s Manual (x1)

KP100 Owner’s Manual (x1)

DTX502/DTX700 Drum Trigger

Module (x1)

Power adaptor (x1)

* May not be included depending on

your particular area. Please check

with your Yamaha dealer.

DTX502/DTX700 Owner’s Manual

(x1)

Module holder (x1)

Module holder screw

(x2 for DTX502 / p1-x4 for DTX700)

 XP70 Tom Pad (x3) Clamp bolt

(for XP70 or XP80; x4)

Hi-hat clutch for

RHH135 (x1)

Tuning key (x1)

* The illustration shows the

DTX502 module holder.

Snare pad

1. Attach a clamp bolt to the snare pad and provisionally tighten

(by five or six turns).

2. Push the snare pad onto the rack’s snare holder. Ensure that

the rod section is fully inserted into the snare pad’s mounting

hole, and then tighten the clamp bolt to secure the pad in

place.

3. Loosen bolts A to D as shown below to adjust the height and

angle of the snare pad. When correctly positioned, be sure to

securely retighten the bolts before proceeding to the next

step.

Tom pads

1. As with the snare pad, attach a clamp bolt to each of the three

tom pads and provisionally tighten (by five or six turns).

2. Push each of the tom pads onto one of the rack’s tom holders.

Each time, ensure that the tom holder’s rod is fully inserted

into the tom pad’s mounting hole, and then tighten the bolt to

secure the pad in place.

3. Loosen bolts A to C as shown below to adjust the height and

angle of each tom pad. When correctly positioned, be sure to

securely retighten the bolts before proceeding to the next

step.

XP80 Snare Pad

Tom pads

XP70

Clamp bolt (tighten in the

direction of the arrow)

Snare pad (rear side)

Insert

Snare pad

Rod sectionSnare holder

Clamp bolt

Bolt A

Bolt C

Bolt D

Bolt B

Tom pad: XP70

Insert

Clamp bolt

Tom holder

Rod section

Bolt C

Bolt B

Bolt A

Assembling the snare and tom pads

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time

without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Continued on other side

Drum trigger module

1. Secure the module holder to the bottom of the drum trigger

module using the module holder screws.

2. Push the module holder into the holder clamp and tighten the

clamp bolt to secure it in place.

Cymbal pads

1. Using the tuning key, loosen the stopper’s key bolt.

2. Remove the wing nut, the two felt pads, and the bolt cover

from the cymbal holder.

3. Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in Step 1

above, it may not be possible to pass the stopper over the

cymbal holder’s shaft. In such a case, loosen the key bolt

as much as possible without removing it.

4. Replace the bolt cover.

* Turn the bolt cover to tighten it onto the threaded section

and firmly secure it in place.

5. With the stopper making full contact with the bottom surface

of the bolt cover as shown below, tighten the stopper’s key

bolt using the tuning key.

6. Place one of the felt pads removed in Step 2 on the cymbal

holder.

7. Mount the pad on the cymbal stand. Lower the pad into place

with the cymbal holder’s shaft passing through the central

hole. When mounted, the stopper’s pin should rest inside the

pad’s smaller hole.

* If you were to play your cymbal pad without the stopper’s

pin positioned well inside the smaller hole, the pad could

rotate, causing the pin to be pulled out. It is very important,

therefore, to ensure that the stopper is secured as shown

in Step 5 above.

8. Assemble the felt pad that came with the cymbal pad.

* The second felt pad removed from the cymbal holder in

Step 2 above is not required for assembly.

9. Tighten the wing nut to secure the pad to the cymbal holder.

A cymbal pad’s built-in sensor is located close to the Yamaha

logo found on the top surface. In order to achieve the best per-

formance from your pad, position it such that the area around

the logo can be easily struck. (See the figure above.)

PCY135

Drum trigger

module

PCY135

Module holder screws

* Two screws for DTX502 /

Four screws for DTX700

Module holder

Drum trigger module

(rear side)

Front side

Clamp bolt

Drum trigger module

module holder

Insert

Holder clamp

Key bolt

Tuning key

Stopper

Cymbal holder

Felt pads

Bolt cover

Wing nut

Cymbal holder

Stopper

Bolt cover

Threaded section

Cymbal holder

Stopper

Bolt cover

Full contact

Cymbal pad

Felt pad that came

with cymbal

Cymbal holder

Felt pad

Bolt cover

Cymbal pad

Stopper

Wing nut

Stopper’s pin

Smaller hole

Assembling the drum trigger module and cymbal pads

1. If a drum mat (sold separately) is not available, lay a sheet of

cardboard on the floor to protect it from being scratched.

2. Loosen the hi-hat stand’s wing bolt a.

3. Open up the three legs as shown below and then retighten

the wing bolt a to lock them in place.

4. Insert the footboard stabilizer rods into the frame holes as

shown below.

5. As shown on the right, loosen the hi-hat clutch’s wing bolt b

and remove the hi-hat clutch.

* The hi-hat clutch is not required when assembling the elec-

tronic drum kit in the standard fashion described in this

manual. Instead, the hi-hat clutch that came with the

RHH135 Real Hi-Hat Pad will be used.

6. Remove the hi-hat shaft from the upper tube .

7. Insert the hi-hat shaft from Step 6 as far as it will go into

the lower tube and screw in the tip.

8. Insert the upper tube over the hi-hat shaft and tighten

the wing bolt c to secure it in place with the cymbal support

plate approximately half way between the top of the lower

tube and the top of the hi-hat shaft .

9. Remove the felt pad attached above the cymbal support

plate. It is not required when assembling the electronic drum

kit in the standard fashion described in this manual.

10. Assemble the RHH135 Real Hi-hat Pad.

* For detailed instructions, refer to the Setting Up section

in the RHH135 Owner’s Manual.

Footboard

stabilizer rod

Wing bolt a

Footboard

stabilizer rod

Felt washer

Hi-hat clutch

Cymbal

support

plate

Cymbal

support plate

Assembling the hi-hat stand

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from being

scratched.

2. Remove the two wing bolts, spring washers, and flat washers from the kick pad frame, and line up each set

nearby in the order of removal.

3. Join the base section to the frame as shown on the right, and then secure it in place by assembling the wing

bolts, spring washers, and flat washers removed in the previous step from the base side.

Frame

Base

Flat washerSpring washer

Wing bolt

Assembling the kick pad

Arrange the hi-hat stand and the kick pad as shown in Example of standard assembly on the other side of this sheet.

• Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place cardboard from the drum kit packaging or the like

on the floor to prevent it from being scratched.

• Ensure that you do not lower the electronic drum rack’s center strut too much as doing so may cause it to come into contact with the kick pad.

Connect the pads to the drum trigger module.

As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.

Connect the drum trigger module to a power supply.

Setting up the drum trigger module.

NOTICE

1. Plug the straight ends of the nine-channel snake cable into the trigger input jacks on the back of the

drum trigger module.

• When using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name

of the corresponding pad.

2. Plug the L-shaped ends of the nine-channel snake cable into the corresponding pads.

3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being

pulled out.

Excessive bending can damage pad cables. Ensure, therefore, that these cables

are not bent at an extreme angle when wrapped around the clips.

Pads DTX502 jack names DTX700 jack names

SNARE q SNARE q SNARE

TOM1 w TOM1/!0 w TOM1

TOM2 e TOM2/!1 e TOM2

TOM3 r TOM3/!2 r TOM3

RIDE t t RIDE RIDE

CRASH y CRASH y CRASH1

KICK u KICK/i o KICK/!0

HI HAT o HI HAT HI HATi

HH CON HI-HAT CONTROL HI-HAT CONTROL

NOTICE

RIDE

TOM3

TOM2

KICK

TOM1

SNARE

CRASH

HI HAT HH CON

Locations of pad jacks

1. Plug the power adaptor’s DC cord into the connector. Hook the power adaptor’s DC cord around

the cord clip to secure it in place.

2. Using the cable bands, secure the cables to the electronic drum rack at the positions circled in the figure

on the right. ( )

3. Plug the adaptor’s AC cord into a domestic wall socket.

Drum trigger module’s rear panel

Cord clip

connector

* The illustration shows the DTX502 drum trigger module.

[For DTX582K Owners]

Select the “DTX582K” trigger setup on the DTX502 drum trigger module. (For details on the trigger

setup procedure, see “Trigger Setup” from the DTX502 Owner’s Manual.)

If “DTX582K” is not displayed on the selection screen, select the “DTX562K” trigger setup, and then

make the following adjustment.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

[For DTX720K Owners]

Select the “DTX720K” trigger setup on the DTX700 drum trigger module. (For details on the trigger

setup procedure, see “Selecting a Sensitivity for the Entire Kit” from the DTX700 Owner’s Manual.)

If “DTX720K” is not displayed on the selection screen, please upgrade your DTX700’s firmware ver-

sion. Visit the following web page for information on the latest DTX700 firmware version and to

download firmware version upgrades.

http://download.yamaha.com/

If you would prefer not to upgrade your firmware version, select the “DTX700K” trigger setup, and

then make the following adjustment.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

Your electronic drum kit is now ready. * For instructions on turning on the drum trigger module, producing sounds, and other subsequent steps,

please refer to the Owner’s Manual that came with the module.

Product specificaties

Merk:	Yamaha
Categorie:	Muziekinstrument
Model:	DTX720K

Heb je hulp nodig?

Als je hulp nodig hebt met Yamaha DTX720K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Muziekinstrument Yamaha

Yamaha YX2035PR Handleiding

20 November 2024

Yamaha THRHBG1 Handleiding

20 November 2024

Yamaha YCH7118 Handleiding

14 November 2024

Yamaha YV-600E Handleiding

14 November 2024

Yamaha YCHS7018 Handleiding

14 November 2024

Yamaha YVD20 Handleiding

14 November 2024

Yamaha YVD10 Handleiding

14 November 2024

Yamaha YCHS7118 Handleiding

14 November 2024

Yamaha Silent Guitar SLG200NW Handleiding

14 November 2024

Yamaha YCH7018 Handleiding

14 November 2024

Handleiding Muziekinstrument

Nieuwste handleidingen voor Muziekinstrument

Aguilar Agro II Handleiding

18 November 2024

Roland KD-7 Handleiding

16 November 2024

Electro Harmonix EHX Volume Handleiding

12 November 2024

Boss FV-500H/FV-500L Handleiding

12 November 2024

Xvive U7 Handleiding

8 November 2024

Pyle PTEDK86 Handleiding

20 Oktober 2024

Casio tone LK-S245 Handleiding

23 September 2024

Casio AP-S200 Handleiding

23 September 2024

Casio AP-300 Handleiding

23 September 2024

Max RhapsodyDP88 Handleiding

18 September 2024