Xvive AT-1 Handleiding

Xvive Niet gecategoriseerd AT-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Xvive AT-1 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

· Signal Generator:

Outputs a 1 kHz sine wave or pink

noise audio signal through XLR male,

1/4", and 1/8" connectors, with three

output level options: -10 dB, -20 dB,

and -40 dB.

· XLR Cable Tester:

Tests whether all three pins of the XLR

cable are functioning properly.

· Phantom Power Check:

Tests the output voltage of the phantom

power and ensures both pins are

functioning properly.

· XLR Input Metering:

Measures the input volume level of

the XLR female connector.

· Headphone and Speaker Monitoring:

When an audio source is connected to the XLR female / 1/4" input, you can

monitor the signal with headphones or speakers via the 1/8" headphone jack.

SPECIFICATIONS

You can use sine waves and pink noise to test the audio inputs of all kinds

of audio gear—including DI boxes, guitar pedals, wireless systems, eect

units, active speakers, mixers, etc.

Checks for phantom power

voltage, which is individually

metered on pins 2 and 3 of

the output XLR. If the voltage

detected is between 24V

and 44V, the LEDs will ash

slowly.

Activating phantom power

on the input channel you are

checking will allow you to

simultaneous test all three

pins in the XLR line.

SIGNAL GENERATOR 1 KHZ SINE WAVE AND PINK NOISE

Audio inputs are ¼” TS and XLR, and the 1/8” output can go to headphones

or a speaker.

The volume knob controls the output volume. When anything is connected

to the 1/8” output jack, the speaker is muted.

Regardless of the routing mode, as long as there is a 1/4" audio signal input,

it will be directly sent to both the speaker and the headphone output.

If you need to monitor the signal more accurately, plug your headphones

into the headphone jack and adjust the level using the volume knob on the

side of the unit.

Charge your AT-1 using a standard USB-C cable and any 5V/2A USB power

supply. A full charge cycle takes about one hour and the device can be

used while charging.

The LED by the USB-C port lights up while the battery is charging, and

turns o when the battery is fully charged.

Always power down your AT-1 after use. Depleting the battery may cause

irreversible damage, resulting in the device being unable to power on

again.

SPEAKER/HEADPHONE OUTPUT

The function LED (11) next to the SEL button will

blink white as a warning when the battery is:

• Low: 3 white blinks

• Out of charge: 6 white blinks

Consider recharging your AT-1 when the rst

‘low battery’ warnings appear.

BATTERY

CHARGING

ALERT

XLR INPUT METERING

XLR CABLE TESTER

PHANTOM POWER CHECK AND XLR PIN CHECK

48V

OUTPUT

Yellow LED: signal output via XLR

Blue LED: signal output via 6.35 mm (1/4”) TS

or 3.5 mm (1/8”) TS

TYPE

OUTPUT LEVEL

10 dB, 40 dB, 20 dB

Solid LED: pink noise

Flashing LED: 1 kHz sine wave

The PK (peak) and SG (signal) LEDs will

illuminate according to the RMS

amplitude of the signal present on the

input XLR. The SG LED is lit when the

signal exceeds -20 dBu RMS, and the

PK LED lights up when the signal

exceeds +10 dBu.

‘SG’ lights up when signal is detected.

‘PK’ lights up when the signal is very

loud. This feature is very useful in noisy

environments, or if you can’t get your

ears close enough to the speaker.

Connect an XLR cable to the input and output to test its 3 pins.

Hold SEL for 2s to enter XLR cable test mode. The LED will automatically

cycle through the pins.

Press SEL to stop the cycle and manually select a pin.

Press TO to resume the automatic cycle.

1 1

2 2

Line ok

Pin2 defective

XLR line

Solid LED: Line ok

Phantom power voltage: 44-52V

pin 1 defective

pin 2 defective

pin 3 defective

Flashing LED: Line ok

Phantom power voltage: 24-44V

_ 01

_ _ 02 _ _ 03 _ _ 04 _ _ 05 _ _ 06 _

English Manual

www.xvive.com

PORTABLE

AUDIO TESTER

AT-1

1. XLR-M output

2. XLR-F input

3. 1/4” output/input

4. 1/8” output

5. Speaker/headphone output

volume knob

6. Speaker

7. USB type-C charging input

8. Power and Charging LED

9. Phantom power pin voltage check

10. Output select: XLR, 6.35 mm

(1/4”)/3.5 mm (1/8”) or speaker

11. Output signal generator Type select:

1 kHz sine wave or pink noise.

Hold 3s for XLR cable tester

12. Output mode / battery life LED

13. Output volume (pad) select

14. Input volume check LED

15. XLR cable test LED

16. Power on/o

48V

ROUTE

XLR

OUTPUT

-5

-10

-20

-30

-40

-50

-60

-∞

+10

PHA NTOM

POW ER

IN P U T LEVEL

PHA NTOM

POW ER

INP UT L EV EL

1/4“ or XLRF input

Headphone or

speaker output

PHA NTOM

POWER

INP UT LEVE L

1/4“ or XLR-F input

Headphone or speaker output

This versatile and compact utility tool includes detection features and oers ve

main functions: a Signal Generator that can emit 1kHz tones or pink noise audio

signals, an XLR Cable Tester for detecting whether XLR cables are damaged, XLR

Input Metering to measure the strength of XLR input signals, a Phantom Power

Check to test voltage and ensure normal operation, and Headphone and

Speaker Monitoring to listen to input signals. It is suitable for testing powered

PA speakers, eect pedals, cables, DI boxes, IEM systems, mixers, and other

audio equipment, making it an essential tool for audio professionals.

TYPICAL VALUES AND TOLERANCES

1/4" unbal jack

XLR balanced jack

-40,-20,-10 dBu-40,-20,-10 dBu

n/a-20 dBu

n/a+10 dBu

600 Ω350 Ω

600 Ω / 3.5 kΩ3 kΩ

n/a

solid: 44 - 52 V

ashing: 24 - 44 V

n/a3.3 V

1 kHz Tone (±1 dB)

GeneratorInput meterImpedanceVoltages

Pink Noise (±1 dB)

'SG' Threshold

'PK' Threshold

Output

Input

Phantom Power

Cable Tester DC

FCC REGULATION WARNING

USE OF POWER ADAPTER ONE-YEAR LIMITED WARRANTYINFORMATION ABOUT COLLECTION AND

DISPOSAL OF OLD ITEMS AND USED BATTERIES

This equipment has been tested and found to comply with the limits for a

Class B digital device,pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit dierent from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

SAFETY INSTRUCTIONS FOR LITHIUM-ION

RECHARGEABLE BATTERIES

If abused or misused, the rechargeable batteries may leak. In extreme

cases, they may even present a risk of explosion, re, heat, smoke or gas.

Xvive does not accept any liability for damage arising from abuse or misuse.

• Keep away from children.

• Only charge rechargeable batteries with chargers recommended by Xvive.

• Observe correct polarity.

• Pack/store charged rechargeable batteries so that the terminals cannot

contact each other (danger of shorting out/re hazard).

• Do not expose to moisture.

• Switch rechargeable battery-powered products o after use.

• Only charge rechargeable batteries at ambient temperatures between

10°C/50°F and 40°C/104°F.

• When not using rechargeable batteries for extended periods of time,

charge them regularly (about every three months).

• Do not mutilate or dismantle.

• Do not heat above 60°C/140°F, e.g. do not expose to sunlight or throw into a re.

• Immediately remove rechargeable batteries from obviously defective products.

• Do not continue to use defective rechargeable batteries.

• Only use rechargeable batteries specied by Xvive.

• Dispose of rechargeable batteries at special collection points or return

them to your specialist dealer.

• Store the products in a cool and dry place at room temperature (approx.

20°C/68°F).

• Remove the rechargeable batteries if the products will not be used for

extended periods of time.

Xvive Corporation Ltd. [Xvive] warrants our products to be free of defects

in materials and workmanship in normal use for a period of one (1) year

from the date of original purchase. Please visit to https://www.xvive.com

Xvive will, at its sole discretion, or in cooperation with our authorized

retailers, repair or replace at no charge, any unit that is inspected by Xvive

or an aliated Xvive service center and deemed to be defective within the

warranty period. This warranty is non-transferrable.

This warranty is only valid to the original purchaser, only when purchased

“new-in-box” from an Authorized Xvive Dealer and with a valid proof of

purchase bearing the purchase date.

Within the USA:

• All Xvive warranty claims should be made with the retailer from which

the unit was purchased. This applies to both retail stores and online retailers.

Outside of the USA:

• For all warranty and non-warranty claims, the purchaser should contact

the Authorized Xvive Retailer from which the unit was purchased within

the country or province in which it was purchased for information on

how to obtain warranty or non-warranty service.

This limited warranty does not cover the following:

• Products that have been modied in any way;

• Any products whose serial numbers have been altered or removed;

• Exterior cosmetic damage or damage to the nish due to misuse or

normal wear and tear;

• Products that were purchased as “used”, items listed as demo stock or

refurbished items;

• Damage to the product or parts caused by improper storage by the user;

• Any freight charges (from or to the retailer);

• Shipping Damage:

- Shipping damage claims must be led with the freight carrier (such as

UPS, FedEx).

- Notify the freight carrier immediately of any shipping damage upon

receipt of damaged items to begin the claim process.

- We also recommend reporting any shipping damage claim within 48

hoursof receipt to the Authorized Retailer from which the item was

purchased.

These symbols on the products, packaging, or on any

documents in the package mean it is incorrect to mix the

used electrical and electronic products and batteries with

general household garbage.

To protect our environment, please take old products and

used batteries to proper collection places, and follow

your national legislation and the Directives 2012/19/EU

and 2006/66/EC.

To deal with these old products and batteries properly,

please help to save valuable resources and prevent any

possibility of side eects on human health and our

environment due to the inappropriate disposal of the old

products and used batteries.

You can contact your local authority for getting more

helpful information on how to dispose the recycling and

collection of the old products and batteries.

[For business users in the European Union]

If you want to discard electrical and electronic item,

please contact your dealer or supplier for further informa-

tion.

[Information on Disposal in other Countries outside the

European Union]

These symbols are only valid in the European Union.

Please contact your local authorities or dealer for more

information on disposal of old items and used batteries.

CAUTION RISK OF ELECTRIC

SHOCK DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE

SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE

APPLIANCE TO RAIN OR MOISTURE.

• Please use a power adapter with the local country certication label.

• Please check the supported voltage and current of the power input and output.

• Please read the warning indications on the power adapter carefully

before use.

• When pulling out the power plug from the socket, please hold the plug

part of the power cord.

• Please disconnect the power adapter plug from the socket when not

using the device for a long time or when there is a lightning strike.

- Keep all original documents and packing materials until the freight

damage claim has a nal resolution.

For units returned to Xvive USA:

• The item must be returned in the same format in which it was purchased.

If a system containing a transmitter and receiver was purchased, then

both units will need to be returned together.

• The purchaser will pay all freight charges to return the original item to

Xvive USA or its aliated service centers.

• If the unit is deemed to be covered by this warranty, Xvive will ship the

repaired or replacement unit to the purchaser free-of-charge and

without any additional freight charges.

• If the unit is deemed to NOT be covered by this warranty, other charges

plus return freight charges will apply.

EXCEPT AS EXPRESSLY SET FORTH ABOVE IN THIS LIMITED WARRANTY,

XVIVE MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES TO THE

EXTENT PERMITTED BY LAW. XVIVE ASSUMES NO LIABILITY FOR PROPERTY

DAMAGE RESULTING FROM FAILURE OF THIS PRODUCT NOR ANY LOSS

OF INCOME, SATISFACTION, OR DAMAGES ARISING FROM THE LOSS OF

USE OF SAME DUE TO DEFECTS OR AVAILABILITY OF SAME DURING

SERVICE.THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU

MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR

BY COUNTRY OR PROVINCE.

For warranty inquiries not covered in this policy,

please contact support@xvive.com

Declaration of Conformity:

This product complies with the requirements of

EMC Directive 2004/108/EG and

Low Voltage Directive 2006/95/EC

_ 08 _ _ 09 _ _ 11 __ 07 _ _ 10 _ _

12 _ _ 13 _

2nd oor, Building 12, Xicheng Industrial Area, Xixiang Town,

Baoan District, Shenzhen Guangdong China. 518101

E-mail: support@xvive.com

Tel: +86-755-2786 6639

SHENZHEN FZONE TECHNOLOGY CO., LTD.

CARE OF DEVICE

1. Do not drop, hit, or apply excessive force to the device.

2. Handle with care and avoid any objects or liquids entering the device.

3. Do not place the device in a place with excessively high or low

temperature.

4. Do not place the device near heat sources, such as heaters or ovens.

5. Do not place the device in a place with excessively high humidity or

with splashing water.

6. Do not place the device in a place with frequent shaking.

7. Do not place the device in a place with excessive sand or dust.

CLEANING OF DEVICE

1. Use a soft dry cloth to wipe o dirt on the exterior of the device.

2. You can slightly dampen a cloth to remove stubborn dirt.

3. When the rubber or silicone parts of the device are stained, use a

lint-free cloth slightly dampened to clean.

4. Do not use abrasive cleaners, wax, alcohol, benzene or paint thinner

as a solvent to wipe the device.

OPERATION OF DEVICE

1. Before connecting any device, please make sure to turn o all device power.

2. Before moving the device, please disconnect all connection cables.

3. Long-term continuous use of the device may cause it to slightly heat

up. Touching it without a burning sensation is normal.

4. Do not hold the device with power on for a long time. Avoid holding

it continuously for a long time during use when it is heating up.

5. Do not use the device for a long time at high volume.

Product specificaties

Merk:	Xvive
Categorie:	Niet gecategoriseerd
Model:	AT-1

Heb je hulp nodig?

Als je hulp nodig hebt met Xvive AT-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Xvive

Xvive AT-1 Handleiding

30 Januari 2025

Xvive A58 Handleiding

22 Augustus 2024

Xvive PX Handleiding

2 Juli 2024

Xvive U3D Handleiding

2 Juli 2024

Xvive U5 Handleiding

2 Juli 2024

Xvive G1 Handleiding

9 Juni 2024

Xvive V19 Micro Power Handleiding

8 Juli 2023

Xvive U2T Handleiding

26 Juni 2023

Xvive U4T Handleiding

25 Juni 2023

Xvive U3C Set Handleiding

13 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Strong LEAP-S3+V2 Handleiding

30 Januari 2025

Strong LEAP-UNA Handleiding

30 Januari 2025

Strong SRT 423 Handleiding

30 Januari 2025

MSI MPG A1250GS PCIE5 Handleiding

30 Januari 2025

Havis CST00216 Handleiding

30 Januari 2025

Havis SC-1000-ACC-14 Handleiding

30 Januari 2025

Havis CST00215 Handleiding

30 Januari 2025

Laica TR1000 Handleiding

30 Januari 2025

Supermicro X14DBI Handleiding

30 Januari 2025

MSI MAG CORELIQUID A15 240 Handleiding

30 Januari 2025