VTech VM3252 Handleiding

VTech Babyfoon VM3252

Lees hieronder de 📖 handleiding in het Nederlandse voor VTech VM3252 (4 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Congratulations

on purchasing your new VTech product. Before

using this product, please read Important

safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech product. Please

review this manual thoroughly to ensure proper

installation and operation of this innovative and

feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

What’s in the box

Install the battery

The parent unit runs on rechargeable battery

or AC power. To continuously monitor your

baby, make sure you use both battery and

AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a

short time only.

NOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Install the battery as shown below.

NOTE

• Press down on the battery compartment cover to

pull it out.

THIS SIDE UP

NOTE

• Make sure the label is facing up THIS SIDE UP

while inserting the battery.

Replace the battery

To replace the battery, pull out the battery

compartment cover, and then lift up the

battery. Follow the steps above to install the

new battery.

Connect and charge the

battery

NOTE

• Use only the power adapters supplied with this

product.

• Make sure the electrical outlets are not controlled

by wall switches.

• The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place if

they are plugged into a ceiling, under-the-table or

cabinet outlet.

• Make sure the parent unit, the baby unit and the

power adapter cords are out of reach of children.

Connect the baby monitor

Charge the parent unit battery

When you have connected the parent unit

and installed its battery for the first time or

after power outage, the parent unit powers on

automatically. The battery icon indicates the

battery status (see the following table).

NOTE

• The parent unit battery is fully charged after

11 hours of continuous charging.

• It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging

time, turn the parent unit off while charging.

• The standby time varies depending on the

volume level you set, your actual use and the

age of the battery.

Battery

indicators

Battery

status

Action

The battery

icon is off

and

displays.

No battery

is installed

but operates

using AC

power, or the

battery has

been installed

incorrectly.

Install the

parent unit

battery.

Charge

without

interruption

(at least 30

minutes).

The screen

displays

Battery low

at Parent

Unit and .

The light

flashes.

The battery

has very little

charge and

may be used

for only a

short time.

Charge

without

interruption

(about 30

minutes).

The battery

icon

becomes

solid .

The battery is

fully charged.

To keep

the battery

charged,

connect it to

AC power

when not in

use.

Before use

NOTE

• This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should

not be used as such.

Test your baby monitor

You may test the baby monitor before initial

use, and at regular times thereafter.

CAUTION

• For hearing protection, make sure the parent

unit is more than 3 feet (1 meter) away from

both baby units. If you hear any high-pitched

noise, move the parent unit further until the

noise stops. You can also press on the VOL-

parent unit to lower or mute the noise.

1. Make sure your baby units and parent unit

are on.

2. The parent unit displays images from the

baby unit.

• Speak towards the microphone of the

baby unit. You will hear the sound at the

parent unit.

3. If you have two baby units, press at the

right side of your parent unit. The screen

switches to other baby unit. Then, repeat

step 2.

NOTE

• the parent unit displaysWhen No ink to Cameral ,

and t he LINK LED light flashes, move the parent

unit closer to the baby units (observe the minimum

distance of 3 feet/ 1 meter). You can also check

if the baby monitor is connected to a live power

socket and switched on.

TIP

• Increase the speaker volume of the parent unit if

you cannot hear the sounds transmitted from the

baby units.

Positioning the baby monitor

CAUTION

• Keep the baby unit out of the reach of baby. your

Never place or mount the baby unit inside the

baby’s crib or playpen.

NOTE

• To avoid interference from other electronic

devices, place your baby monitor far away from

devices such as wireless routers, microwaves,

cell phones and computers.

1. Place the baby units more than 3 feet

(1 meter) away from your baby.

2. Adjust the angle of the baby unit camera to

aim at your baby.

3. Place the parent unit more than 3 feet

(1 meter) away from the baby units.

CAUTION

• The default volume of your parent unit is level

3, and the maximum volume is level 5. If you

experience high-pitched screeching noise from

your baby monitor while positioning:

-Make sure your baby units and parent unit are

more than 3 feet (1 meter) apart, OR

-Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is

up to 1,000 feet (300 meters) outdoors or

160 feet (50 meters) indoors. The actual

operating range may vary depending on

the environmental conditions and other

interferences such as walls, doors and other

obstructions.

Overview

Baby unit overview

1PAIR

• Your baby units and parent unit

provided are already paired.

2POWER LED light

• On when the baby unit is turned on.

• Flashes when the baby unit is not

being viewed; or when the link to the

parent unit is lost.

3Microphone

4Camera

5Infrared LEDs

6Light sensor

7 ON/OFF switch

• Slide to turn on or off the baby unit.

8Speaker

9Power jack

10 Wall mount holes

Parent unit overview

1 LED lights

• Indicate the different statuses of

the parent unit. For details, refer to

Parent unit lights.

2LCD display

3 Zoom

• Press to zoom in or out while

viewing image.

• Press to change the screen to view

images from different baby units.

• For VM3252-2 only

LCD ON/OFF

• Press and hold to turn on or off the

LCD screen.

5MENU/SELECT

• Press to enter/exit the menu.

• While in a sub-menu, press to

choose an item, or save a setting.

6Microphone

• While in a menu, press to scroll up,

or to enter an item’s sub-menu.

• While zooming, press and hold to

move the zoomed image upward.

• While in a menu, press to scroll

down.

• While zooming, press and hold to

move the zoomed image downward.

• While in a menu, press to choose

the next item on the left, or enter

into the submenu, if any.

• While zooming, press and hold to

move the zoomed image leftward.

• While in a menu, press to choose

the next item on the right, or return

to the main menu while in submenu.

• While zooming, press and hold to

move the zoomed image rightward.

8 On/off

• Press and hold to power on.

• Press and hold again to power off.

9TALK

• Press and hold to talk to the

selected baby unit.

10 VOL-

• Turn down the volume when the

speaker is on.

11 VOL+

• Turn up the volume when the

speaker is on.

12 Speaker

13 Power jack

14 Battery compartment cover

15 Stand

Parent unit lights

LINK On when the parent unit is linked to

the baby unit.

Flashes quickly when the link to the

baby unit is nearly lost.

On when the parent unit is

connected to AC power, or the

battery is charging.

Flashes when the parent unit

battery is low and needs charging.

Off when the parent unit is

disconnected from AC power.

On when the speaker volume of the

parent unit is turned off.

TALK On when the parent unit is talking to

the baby unit.

Parent unit status icons

Connection status

• or displays when strong

signal strength is detected

between the baby unit and the

parent unit.

• or displays when moderate

or low signal strength is detected

between the baby unit and the

parent unit.

Patrol mode

• Displays when the parent unit is in

PATROL mode.

• For VM3252-2 only

Current view status

• Displays the baby unit number of

the baby unit that is being viewed.

Zoom

• Displays when the current image

on the parent unit has zoomed in.

Night vision

• Displays when the baby unit being

viewed has activated the night

vision feature.

Lullaby

• Displays when a lullaby is playing.

Talkback

• Displays when talking back to the

baby units from parent unit.

6-level sound indicator

Displays the sound level according

to the scales of loudness when there

is sound transmitted from the baby

unit.

• (1 to 2 bars) indicates low sound

level detected by the baby unit.

• (3 to 4 bars) indicates

moderate sound level detected by

the baby unit.

• (5 to 6 bars) indicates high

sound level detected by the baby

unit (e.g. baby crying loudly).

Mute alert

• Displays when the parent unit

speaker volume is set to off.

Real-time temperature

• Displays the real-time temperature

detected by the baby unit in

Fahrenheit (oF) or Celsius (oC)

(e.g. 57

oF or 14

oC).

Battery status

• animates

when the battery is charging.

• displays solid when the

battery is fully charged.

• displays when the battery is

low and needs charging.

AC power without battery

• Displays when the parent unit is

connected to AC power without

the battery.

Speaker volume

• Displays the parent unit speaker

volume level while adjusting.

Parent unit main menu icons

Brightness

You can change the brightness of

the parent unit screen.

LCD screen off timer

You can set a specific time to

screen off your parent unit.

Temperature

You can choose to set the maximum/

minimum temperature and turn on

the temperature alert tone, so that

the parent unit beeps whenever the

room temperature detected by the

baby unit falls outside of the desired

temperature range.

You an also choose to display the

temperature in Fahrenheit (oF) or

Celsius (oC) on your parent unit.

Lullaby

You can select, play, or stop a

lullaby.

VOX sensitivity

With this feature, you can choose

to hear sounds from the baby unit

all the time, or to hear sounds

that exceed a certain level. You

can use the parent unit to adjust

the microphone sensitivity of

your baby unit. The higher the

sensitivity level, the more sensitive

the baby unit is in detecting

sounds for transmitting to the

parent unit.

Sound-activated screen

When the baby unit being viewed

detects no sound, the parent

unit screen stays off to save

power. Once a sound is detected,

the parent unit screen turns on

automatically. It will then turn

off again after 50 seconds of no

sound detection.

Patrol mode

You can monitor your baby in

PATROL mode.

• For VM3252-2 only

Parent unit warning icons and

messages

No link to Camera The link between the

baby unit and the parent

unit is lost.

/Battery low

at Parent Unit

The battery is empty and

needs to be recharged.

Operation is in progress.

/Temperature

too high

/Temperature

too low

The temperature detected

by the baby unit is higher/

lower than the desired

temperature alert range.

The parent unit is

searching for baby units.

Using the baby monitor

Power on or off the baby unit

• Slide the switch down to turn on ON/OFF

the baby unit. The POWER LED light turns

on.

• Slide the switch up to turn off ON/OFF

the baby unit. The POWER LED light turns

off.

Power on or off the parent unit

• Press and hold to turn on the parent unit.

The screen turns on.

• Press and hold again to turn off the

parent unit. The screen turns off.

Turn on or off the parent unit

screen

You can turn on or off the parent unit screen

without powering off the parent unit. You can

still hear sound from the baby unit.

• Press and hold on the parent LCD ON/OFF

unit to turn off the screen.

• Press any key on the parent unit to turn on

the screen again.

Screen off timer

You can set the screen off time for the parent

unit when there is no key press for a specific

time interval.

When the screen is turned off, you can still hear

sound from the baby unit.

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. or to choose the desired time Press

period to time off screen ( / / /

), then press to confirm your SELECT

selection.

Adjust LCD brightness

You can change the brightness of the parent

unit screen from to . The LCD Level 1 Level 5

brightness is preset to .Level 3

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose the desired level of

brightness, then press to confirm SELECT

your selection.

Adjust the sound sensitivity of

the baby unit

You can choose to hear sounds from the baby

unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to

adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more

sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The VOX

sound sensitivity is preset to the highest level.

Sensitivity

Level

Description

Highest

Low

sensitivity

High

sensitivity

Highest VOX sensitivity

level

The parent unit speaker

is constantly on, and

you will hear all sounds

(including background

noises) from your baby’s

room.

High

High VOX sensitivity

level

The parent unit speaker

turns on for soft babbling

and louder sounds from

your baby. It remains quiet

when your baby sleeps

soundly.

Medium

Medium VOX sensitivity

level

The parent unit speaker

turns on for loud babbling

and louder sounds from

your baby. It remains

quiet when your baby

makes soft sounds.

Low

Low VOX sensitivity

level

The parent unit speaker

turns on for crying and

louder sounds from your

baby. It remains quiet

when your baby makes

soft sounds.

Lowest

Lowest VOX sensitivity

level

The parent unit speaker

turns on for loud crying

or screeching sounds

from your baby. It remains

quiet when your baby

makes soft sounds.

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose the desired

sensitivity level, then press to SELECT

confirm your selection.

TIP

• You can adjust the baby unit placement to

improve the sound detection.

Turn on or off the sound

activation

When sound activation is on, as long as no

sound is detected within 50 seconds, the

parent unit screen will turn off automatically to

save power.

When your baby unit detects a sound, which

exceeds the selected sensitivity level, the

sound activation triggers the parent unit

screen to turn on automatically. When no

sound is detected within 50 seconds, the

screen will be off again.

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose or , then

press SELECT to confirm your selection.

NOTE

• If the sound sensitivity is set to the highest level,

or lullaby is playing, the parent unit screen may

remain on continuously even though sound

activation is on. This depends on whether the

baby unit detects any sounds.

Adjust speaker volume

For parent unit:

• Press on the parent unit to VOL-/VOL+

adjust the speaker volume.

NOTE

• When the parent unit speaker volume is set to

zero, appears on the screen and the light

turns on.

For baby unit:

The baby unit speaker volume determines the

lullaby and talkback volume transmitted from

your parent unit.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press to choose .

4. Press or to choose the volume level of

the lullaby on the baby unit.

5. Press to confirm your selection.SELECT

Monitoring mode

* For VM3252-2 only

Every time the parent unit is turned on, it

displays a baby unit in SINGLE-CAM mode.

If there are two baby units in your system, you

can also monitor your baby in PATROL mode.

SINGLE-CAM The screen displays

image of a single baby

unit in full screen.

PATROL A single cam view that

transits to a different baby

unit every 10 seconds.

To switch to another camera:

• Press to switch to another camera.

Press .

To switch between SINGLE-CAM and

PATROL mode:

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to switch on or off PATROL

mode, then press to confirm your SELECT

selection.

• In PATROL mode, the camera view

transits to a different baby unit every 10

seconds.

10s

User’s manual

VM3252

VM3252-2

Video Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

>3ft (1m)

> More than 3

feet (1 meter)

1 set for VM3252

2 sets for VM3252-2

Zoom

You can zoom in while viewing images from

the baby unit.

• Press to zoom in.

• Press and hold or to move the

zoomed image upward or downward.

• Press and hold or to move the zoomed

image leftward or rightward.

• Press again to zoom out.

Talk

You can use the function of the parent TALK

unit to comfort your baby.

1. Press and hold on the parent unit. TALK

The light turns on.TALK

2. Speak towards the microphone on the

parent unit. Your voice is broadcast to the

baby unit.

3. Release the key to stop the TALK

broadcast. The light goes off.TALK

Lullaby

The baby monitor has five lullabies and four

soothing sounds for you to comfort your baby.

You can play the lullabies or soothing sounds

on the baby unit using the parent unit.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press to choose , then press .

4. Press or to choose a lullaby, or choose

to stop playing.

5. Press to confirm your selection. SELECT

NOTE

• The lullaby stops when you started using TALK

function of the parent unit to comfort your baby. It

will resume in a few seconds after the broadcast

is ended.

Monitor the temperature

Your baby unit monitors the temperature of

your baby’s room with its built-in temperature

sensor. If the detected temperature is out of the

preset temperature range, the parent unit will

display an alert message.

Set temperature range

You can set the desired room temperature

alert range. The minimum temperature can

be set between 50 oF (10 oC ) and 76 oF (24

oC). The maximum temperature can be set

between 77 oF (25 oC) and 102 oF (39 oC).

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose , then press .

4. Press or to choose or , then

press .SELECT

5. Press or to choose the desired

minimum or maximum temperature, then

press to confirm your selection.SELECT

Temperature alert tone

You can turn on the temperature alert tone so

that the parent unit will emit an alert tone if the

detected temperature is out of range.

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose , then press

SELECT.

4. Press or to choose or , then

press to confirm your selection.SELECT

Temperature format

You can choose to display the temperature in

Fahrenheit (oF) or Celsius (oC).

1. Press when the parent unit is idle.MENU

2. Press or to choose , then press .

3. Press or to choose , then press

SELECT.

4. Press or to choose or , then

press to confirm your selection.SELECT

Night vision

The baby unit has infrared LEDs that allow

you to see your baby clearly at night or in a

dark room. When the baby unit being viewed

detects low light levels, the infrared LEDs are

switched on automatically. The images from

the baby unit are in black and white, and

appears on screen.

NOTE

• It is normal if you see a short white glare on your

parent unit screen as the baby unit is adapting to

the dark environment.

• When the infrared LEDs are on, the images are in

black and white. This is normal.

TIP

• Depending on the surroundings and other

interfering factors, like lightings, objects, colors

and backgrounds, the display resolution may vary.

Adjust the baby unit’s angle or place the baby unit

at a higher level to prevent glare and blurry display.

Mount the baby unit (optional)

Your baby monitor comes ready for tabletop

use. You can also choose to mount your baby

monitor on the wall. See Mount the baby unit

(optional) in the Quick Start Guide for the wall

mounting instructions.

General product care

To keep this product working well and looking good,

follow these guidelines:

• Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

fluorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for

some time, remove the rechargeable battery from

the parent unit. Store the parent unit, the baby unit

and the adapters in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the baby monitor. If you cannot find the answer to your

question, visit our website at www.vtechphones.com,

or contact for customer service.1 (800) 595-9511

Why does the

baby monitor

not respond

normally?

Try the following (in the order

listed) for common cure:

1. Disconnect the power to the

baby units and the parent unit.

2. Remove the batteries in the

parent unit. Then, install the

batteries again.

3. Wait a few seconds before

connecting power back to the

baby units and the parent unit.

4. Turn on the baby units and the

parent unit.

5. Wait for the parent unit to

synchronize with the baby units.

Allow up to one minute for this to

take place.

Why don’t

the power-on

light of the

baby unit and

parent unit

go on when I

switch on the

units?

Perhaps the parent unit is not

connected to the power. Insert the

appliance plug into the parent unit

and put the adapter in a wall socket.

Then, press and hold to switch

on the parent unit and to establish

connection with the baby unit.

Perhaps the baby unit is not

connected to the power. Insert

the appliance plug into the baby

unit and put the adapter in a wall

socket. Then, slide the ON/OFF

switch to to switch on the baby ON

unit and to establish connection

with the parent unit.

Why doesn’t

my parent

unit charge

while

connected to

AC power?

Make sure the power is not

controlled by a wall switch.

Make sure the battery is installed.

You may have used the battery for

a long time. Replace a new battery.

Why is my

screen in

black and

white?

The screen is in black and white

during night-time or in a dark room

when the night vision feature is

activated. This is normal.

Why do I

get glare or

blurry display

on my screen

when viewing

my baby at

night?

During night-time or in a dark

room, the surroundings and other

interfering factors, like lightings,

objects, colors and backgrounds

may affect the image quality on

your parent unit screen. Adjust the

baby unit’s angle or place the baby

unit at a higher level to prevent

glare and blurry display.

Why does the

baby monitor

produce a

high-pitched

noise?

The parent unit and baby units may

be too close to each other.

• Move the parent unit away from

the baby units until the noise

stops; OR

• Turn down the volume of your

parent unit.

Why does

the parent

unit beep?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

If the parent unit is powered by the

provided battery, it may not have

enough charge for the parent unit to

perform normally. Charge the battery

in the parent unit for up to 11 hours.

The temperature of your baby’s

room may be too high or too low.

Why does

the parent

unit react

too quickly

to other

sounds?

The baby unit also picks up other

sounds than those of your baby.

Adjust the sensitivity level to a

lower level or lower the parent unit

speaker volume.

Why don’t

I hear a

sound/Why

can’t I hear

my baby cry?

The parent unit speaker volume

may be too low or off. Press VOL+

to increase the volume.

You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby

unit to set to a higher level.

Why can’t I

establish a

connection?

Why is the

connection

lost every

now and

then? Why

are there

sound

interruptions?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to

reduce the risk of fire, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on

the product.

2. Adult setup is required.

3. This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

4. This product is not intended for use as a medical

monitor.

5. Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.

6. CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion

if a wrong type of battery is used for the parent

unit. Use only the supplied rechargeable battery

or replacement battery pack (BT207695) for

the parent unit. Do not dispose of batteries in a

fire. They may explode. Dispose of used battery

according to the information in The RBRC® seal.

7. Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Output: 6V DC 500mA

Parent unit power adapter: Output: 6V DC 500mA.

8. The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

9. For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be

easily accessible.

10. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

11. Unplug the power cords before replacing

batteries.

12. Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

13. Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.

14. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.

15. Do not overload wall outlets or use an extension

cord.

16. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

17. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.

18. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than specified

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

20. You should test the sound reception every

time you turn on the units or move one of the

components.

21. Periodically examine all components for

damage.

22. Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.

23. Children should be supervised to ensure that

they do not play with the product.

24. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature

between 32oF and 104oF.

2. Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

3. Batteries should not be exposed to excessive

heat such as bright sunshine or fire.

4. Warning—Strangulation

Hazard—Children have

STRANGLED in cords. Keep

this cord out of the reach of

children (more than 3 ft (0.9

m) away). Do not remove this

tag.

5. Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

6. Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away

from these electronic devices as possible:

wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital cordless

devices):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches

from the pacemaker.

• Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards

regarding electromagnetic fields (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientific evidence available today.

The RBRC® seal

The RBRC® seal on the Ni-MH battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful

lives, when taken out of service within the United

States and Canada.

The RBRC® program provides a convenient

alternative to placing used Ni-MH batteries into the

trash or municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH

battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is

part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY®

are registered trademarks of the

Rechargeable Battery Recycling

Corporation.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more. The transmitter and antenna of the

parent unit shall be held at least 1 in (2.5 cm) from

your face.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licence-

exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference,

including interference that may cause undesired

operation.

The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada

technical specifications were met.

This product meets the applicable Industry Canada

technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The baby unit should be installed and

operated with a minimum distance of 8 in (20 cm)

between the baby unit and all persons’ body. Use of

other accessories may not ensure compliance with

FCC RF exposure guidelines. This transmitter must

not be co-located or operating in conjunction with

any other antenna or transmitter. This equipment

complies also with Industry Canada RSS-102 with

respect to Canada’s Health Code 6 for Exposure of

Humans to RF Fields.

California Energy Commission

battery charging testing mode

This baby monitor meets the California Energy

Commission (CEC) regulations for energy

consumption. Your baby monitor is set up to comply

with the energy-conserving standards right out of the

box.

Follow the instructions to install and charge the

battery. The CEC battery charging testing mode is

activated while charging.

Even if the parent unit is paired to baby units, the

CEC battery charging testing mode is activated

while it is powered off and charging.

For C-UL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez

toujours suivre certaines mesures de précaution

de base aﬁn de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont

ceux qui suivent :

1. Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce produit a été conçu pour être un dispositif

d’appoint seulement. Il n’est pas le remplacement

d’une supervision responsable et adéquate par

un adulte et ne devrait pas être utilisé comme

telle.

4. Ce produit n’est pas conçu pour être utilisé en

tant que moniteur médical.

5. N’utilisez pas cet appareil près de l’eau ni de

toute autre source d’humidité, par exemple, près

d’une baignoire, cuve à lessive, évier de cuisine,

dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

6. MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de

piles pour l’unité du parent. N’utilisez que le

bloc-piles rechargeable inclus ou le bloc-piles de

rechange (BT207695). N’incinérez pas les piles.

Celles-ci risqueraient d’exploser. Jetez les piles

usées selon les renseignements suivant le sceau

du RBRC ®.

7. N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre

votre sécurité en péril.

Adaptateur de l’unité du bébé :

Sortie : 6V CC 500mA

Adaptateur de l’unité du parent :

Sortie : 6V CC 500mA

8. Lorsqu’ils sont branchés dans une prise de

courant, les adaptateurs secteur ont été conçus

pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas

été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici

est branché dans une prise au plafond, sous une

table ou dans un meuble.

9. Pour les PRODUITS À BRANCHER À UNE

PRISE DE COURANT, la prise de courant doit

être installée près du produit, aﬁn d’assurer une

accessibilité sécuritaire à la prise de courant.

10. Débranchez ce produit de la prise de courant

avant de procéder au nettoyage. N’utilisez pas de

nettoyants en aérosols. Utilisez un chiffon humide

pour le nettoyer.

11. Débranchez les cordons d’alimentation avant de

remplacer le bloc-piles.

12. Ne coupez pas les cordons d’alimentation pour

remplacer les ﬁches, car ceci peut présenter un

danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur

le cordon d’alimentation. N’installez pas cet

appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur l’étiquette. Si

vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale

d’électricité.

15. Ne surchargez pas les prises de courant

murales ni les rallonges électriques.

16. Ne placez pas cet appareil sur un chariot,

meuble, trépied, support de montage ni table

chancelants.

17. Les trous et ouvertures du boîtier, situés à

l’arrière de l’appareil ou sous celui-ci, servent à

aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus,

ne placez pas l’appareil dans un endroit avant

de vous assurer qu’il y ait une bonne circulation

d’air.

18. N’enfoncez jamais d’objets à travers les

ouvertures de cet appareil, car ils pourraient

entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui

peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide

dans ce produit.

19. Aﬁn de réduire les risques d’électrocution, ne

démontez pas cet appareil, mais apportez-le

dans un centre de service autorisé. L’ouverture

du boîtier ou le retrait de toutes pièces que

contient cet appareil, à l’exception de l’accès

autorisé à certaines portes ou ouvertures,

risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage

incorrect peut par la suite présenter des risques

d’électrocution.

20. Vous devriez tester la réception chaque fois que

vous mettez l’appareil en fonction.

21. Examinez les composantes aﬁn de vériﬁer si

celles-ci ne sont pas endommagées.

22. Soyez avisé de la perte de la conﬁdentialité

lorsque vous utilisez les ondes publiques. Les

conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones

sans ﬁl, des scanneurs, etc.

23. Les enfants devraient être supervisés aﬁn de

vous assurer qu’ils ne jouent pas avec l’appareil.

24. Le produit n’est pas conçu pour être utilisé

par des personnes (incluant des enfants) aux

capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné

sufﬁsamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une

température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des

chaleurs extrêmes, ainsi qu’à la lumière directe

du soleil. Ne l’installez pas près d’une source de

chauffage.

3. Le bloc-piles ne doit pas être exposé à la

chaleur excessive telle que la lumière du soleil

ou au feu.

4. Assurez-vous que le moniteur

et le cordon de l’adaptateur

sont toujours hors de portée

des enfants, àau moins 1

mètre (3 pieds) de l’enfant ou

du berceau, pour éviter tout

risque de strangulation.

5. Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir

le moniteur ou l’unité (s) portative avec un article

tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent

produire des interférences sur votre moniteur

vidéo et audio. Tentez d’installer votre

moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil,

radios, téléphones cellulaires, interphones,

moniteurs, téléphones, ordinateurs personnels,

électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux

dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à

au moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

L’étude effectuée par l’organisme WRS n’a pas

identifié de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent

dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes

les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions

de ce guide, son utilisation sera sécuritaire pendant

de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons

aujourd’hui.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible;

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 below); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for

damage or loss of the Product in transit. If the Product

failure is not covered by this limited warranty, or proof

of purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

What must you return with the Product to get

warranty service?

1. Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difficulty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modifications to this limited warranty and you

should not rely on any such modification.

State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other

rights, which vary from state to state or province to

province.

Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost profits or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical specifications

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Baby unit: 2405 - 2475 MHz

Parent unit: 2405 - 2475 MHz

Channels 32

LCD 2.8” Color LCD

(WQVGA 320x240 pixel)

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements Parent unit: 3.6V Ni-MH battery

Baby unit power adapter: Output:

6V DC @ 500mA

Parent unit power adapter: Output:

6V DC @ 500mA

Specifications are subject to change without notice.

Document order number: 91-010825-030-100

Product specificaties

Merk:	VTech
Categorie:	Babyfoon
Model:	VM3252

Heb je hulp nodig?

Als je hulp nodig hebt met VTech VM3252 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Babyfoon VTech

VTech RM9751 Handleiding

13 December 2024

VTech RM5754-2HD Handleiding

13 December 2024

VTech RM5764-2HD Handleiding

13 December 2024

VTech VC2105 Handleiding

13 December 2024

VTech RM2751 Handleiding

13 December 2024

VTech RM5754HD Handleiding

13 December 2024

VTech VM3252 Handleiding

16 November 2024

VTech RM5764HD Handleiding

16 November 2024

VTech DM1211 Handleiding

16 November 2024

VTech RM5766HD Handleiding

27 Februari 2024

Handleiding Babyfoon

Nieuwste handleidingen voor Babyfoon

Alecto DVM-200 Handleiding

14 November 2024

Oricom SC330 Handleiding

10 December 2024

Alecto DVM200XL Handleiding

4 December 2024

D-Link DCS-825L Handleiding

23 November 2024

Chipolino Polaris Handleiding

16 November 2024

Neno Bambino Handleiding

15 November 2024

Babymoov YOO-Care A014422 Handleiding

15 November 2024

Oricom RVSL01 Handleiding

10 November 2024

Oricom RGB Handleiding

10 November 2024

Alecto DVM2028 Handleiding

5 November 2024