VTech VM2251-2 Handleiding

VTech Babyfoon VM2251-2

Lees hieronder de 📖 handleiding in het Nederlandse voor VTech VM2251-2 (2 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Note

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.

Test your baby monitor

You may test the baby monitor before initial use, and at regular times thereafter.

Caution

• For hearing protection, make sure the parent unit is

more than 3 feet (1 meter) away from both baby units. If

you hear any high-pitched noise, move the parent unit

further until the noise stops. You can also press VOL on

the parent unit to reduce the noise.

1. Make sure your baby unit and parent unit are on.

2. The parent unit displays images from the baby unit.

• Speak towards the microphone of the baby unit. You will hear the sound at the parent unit.

3. If you have two baby units, view the image from one of them by switching cameras via

menu. Then, repeat step 2.

Note

• When the parent unit displays No link to Camera, and the POWER LED light ﬂashes, move the parent

unit closer to the baby units (observe the minimum distance of 3 feet / 1 meter). You can also check if

the baby unit is connected to a live power socket and switched on.

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby units.

Positioning the baby monitor

Caution

• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

Note

• To avoid interference from other electronic devices, place

your baby monitor far away from devices such as wireless

routers, microwaves, cell phones and computers.

1. Place the baby units more than 3 feet (1 meter)

away from your baby.

2. Adjust the angle of the baby unit camera to aim at

your baby.

3. Place the parent unit more than 3 feet (1 meter)

away from the baby units.

Caution

• The default volume of your parent unit is level 3, and the

maximum volume is level 5. If you experience high-pitched

screeching noise from your baby monitor while positioning:

- Make sure your baby units and parent unit are more than

3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to 1000 feet (300 meters) outdoors or 160 feet

(50 meters) indoors. The actual operating range may vary depending on the environmental

conditions and other interferences such as walls, doors and other obstructions.

Power on or off the baby unit

• Slide the ON/OFF switch to ON to turn on the baby unit. The POWER LED light turns on.

• Slide the ON/OFF switch to OFF to turn off the baby unit. The POWER LED light turns off.

Power on or off the parent unit

• Slide the ON/OFF switch to ON to turn on the parent unit. The screen and the POWER LED

light turns on.

• Slide the ON/OFF switch to OFF to turn off the parent unit. The screen and the POWER

LED light turns off.

Adjust parent unit speaker volume

• Press VOL /VOL on the parent unit to adjust the speaker volume.

Adjust LCD brightness

You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD

brightness is preset to Level 3.

1. Press when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose the desired level of brightness, then press to conﬁrm your selection.

Monitoring mode * for VM2251-2 only

Every time the parent unit is turned on, it displays a baby unit in SINGLE-CAM mode. If there

are more two baby units in your system, you can also monitor your baby in PATROL mode.

SINGLE-CAM The screen displays image of a single baby unit in full screen.

PATROL A single cam view that transitions to a different baby unit every 10 seconds.

To switch from SINGLE-CAM to PATROL mode:

1. Press when the parent unit is idle.

2. Press or to choose , then press or to open the submenu.

3. Press or to select to enter PATROL mode to alternately view the image from one

baby unit to the next one in every 10 seconds.

To switch from PATROL to SINGLE-CAM mode:

1. Press when the parent unit is idle.

2. Press or to choose , then press or to open the submenu.

3. Press or to select a camera number to enter SINGLE-CAM mode.

Note

• If one or more paired baby units are powered off or disconnected during patrolling, the parent unit

will keep searching until its power has run out or a baby unit is connected once again.

1Pair hole

• Your baby units and parent unit

provided are already paired.

2POWER LED light

• On when the baby unit is turned on

and is paired to the parent unit.

• Flashes when the baby unit is not

being viewed;

or when the link to the parent unit is

lost.

3Microphone

4Camera

5Infrared LEDs

6Light sensor

7 ON/OFF switch

• Slide to turn on or off the baby unit.

8Speaker

9Power jack

10 Wall mount holes

NOTESNOTE

• The rechargeable battery is pre-installed in your parent unit.

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to the switch controlled electric outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapt\er cords are out of reach of children.

Connect the baby monitor

Charge the parent unit battery

When you have connected and turned on the parent unit, the battery will be charged

automatically. The battery icon indicates the battery status (see the following table).

NOTESNOTE

Notes

• The parent unit battery is fully charged after 11 hours of continuous charging.

• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,

turn the parent unit off while charging.

• The standby time varies depending on the volume level you set and your actual use.

Battery indicators Battery status Action

The screen displays Battery

low at Parent Unit. The

or light ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without interruption

(about 30 minutes).

The battery icon becomes

solid . The battery is fully

charged. To keep the battery charged,

connect it to AC power when

not in use.

User’s manual

VM2251

VM2251-2

Video Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety

instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

1 set for VM2251

2 sets for VM2251-2

Screen off timer

You can set the screen off time for the parent unit when there is no key press for a speciﬁc time interval.

When the screen is turned off, you can still hear sound from the baby unit.

1. Press when the parent unit is idle.

2. Press or to choose , then press or to open the submenu.

3. Press or to choose the desired time period to automatically turn off screen

( / - 5 min./ - 30 min. / - 60min.), then press to conﬁrm your selection.

Adjust the sound sensitivity of the baby unit

You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for

transmitting to the parent unit. The VOX sensitivity level is preset to the highest level (Level 5).

VOX

Sensitivity

level Level 5 Level 4 Level 3 Level 2 Level 1

Sensitivity Highest VOX

sensitivity level High VOX

sensitivity level Medium VOX

sensitivity level Low VOX

sensitivity level Lowest VOX

sensitivity level

Description The parent

unit speaker is

constantly on,

and you will

hear all sounds

(including

background

noises) from

your baby’s

room.

The parent

unit speaker

turns on for

soft babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby sleeps

soundly.

The parent

unit speaker

turns on for

loud babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent unit

speaker turns

on for crying

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent

unit speaker

turns on for

loud crying

or screeching

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

1. Press when the parent unit is idle.

2. Press or to choose , then press or to open the submenu.

3. Press or to choose the desired sensitivity level, then press to conﬁrm your selection.

NOTESNOTE

Note

• If the screen is off, and the setting of sound-activated screen is ON, then LCD screen will be turned on

automatically when VOX sensitivity is triggered.

Tip

• If you want to use a sound machine or white noise machine for natural white noise while using this baby

monitor to check on your baby, you can:

- Lower the volume of your sound machine or white noise machine; or

- Lower the sensitivity level of your baby monitor to medium (level 3) or below. Default level is the highest level.

Turn on or off the sound activation

When sound activation is on, as long as no sound is detected within 50 seconds, the parent unit

screen will turn off automatically to save power.

When your baby unit detects a sound, which exceeds the selected sensitivity level, the sound

activation triggers the parent unit screen to turn on automatically. When no sound is detected

within 50 seconds, the screen will be off again.

1. Press when the parent unit is idle.

2. Press or to choose , then press or to open the submenu.

3. Press or to choose or , then press to conﬁrm your selection.

Note

• If the sound sensitivity is set to the highest level, the parent unit screen may remain on continuously

even though sound activation is on. This depends on whether the baby unit detects any sounds.

Zoom

You can zoom in while viewing images from the baby unit.

• Press to zoom in. Press again to zoom out.

• Press , , or to move the zoomed image downward, upward, leftward or rightward.

Talk

You can use the TALK function of the parent unit to comfort your baby.

Press and hold TALK on the parent unit.

1. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.

2. Release the TALK key to stop the broadcast.

Monitor the temperature

Your baby unit monitors the temperature of your baby’s room with its built-in temperature

sensor. If the detected temperature is out of the preset temperature range, the parent unit

will display an alert message.

Set temperature range

You can set the desired minimum and maximum room temperature alert ranges.

1. Press when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose , then press .

4. Press or to choose or , then press .

5. Press or to choose the desired minimum or maximum temperature, then press to

conﬁrm your selection.

Temperature alert tone

You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the

detected temperature is out of range.

1. Press when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose , then press .

4. Press or to choose or , then press to conﬁrm your selection.

Temperature format

You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).

1. Press when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose , then press .

4. Press or to choose or , then press to conﬁrm your selection.

Connect and charge the battery

What’s in the box

Before use

Using the baby monitor

Baby unit overview

3 Using the baby monitor (Con’t)

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 2407.5 - 2475 MHz

Parent unit: 2407.5 - 2475 MHz

Channels 21

LCD 2.4” Color LCD

(QVGA 320x240 pixel)

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range

may vary according to environmental conditions at the time of use.

Power requirements Parent unit: 3.6V Ni-MH battery

Baby unit power adapter: Output: 6V DC @ 400mA

Parent unit power adapter: Output: 6V DC @ 400mA

Technical speciﬁcations

Speciﬁcations are subject to change without notice.

Document order number: 91-010824-050-100

3 ft (1m)

Parent unit overview

1 POWER LED light

• Green when the parent is powered

on.

• Flashes green when no link to

camera.

2TALK

• Press and hold to talk to the selected

baby unit.

> 3ft (1m)

＜3ft (1m)

＞3ft (1m)

> 3ft (1m)

﹏﹏﹏

﹏﹏﹏﹏

﹏﹏﹏﹏﹏

﹏﹏﹏

﹏﹏﹏﹏

﹏﹏﹏﹏﹏

< 3ft (1m)

63ē

≥

< 3ft (1m)

3ft (1m)

63ē

≥

< 3ft (1m)

3ft (1m)

63ē

< 3ft (1m)

3ft (1m)

＜3ft (1m)

＞3ft (1m)

When using your equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock

and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for

any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist

you in supervising your baby.

4. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

5. CAUTION: Use only the batteries provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit.

Do not dispose of batteries in a ﬁre. They may explode. Dispose of used battery according to the information in The RBRC® seal.

6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.

Baby unit power adapter: Output: 6V DC 400mA; Parent unit power adapter: Output: 6V DC 400mA.

7. The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

9. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

10. Unplug the power cords before replacing batteries.

11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure

of the type of power supply in your home, consult your dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back

or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be

blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or

over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or

create a short circuit. Never spill liquid of any kind on the product.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.

Opening or removing parts of the product other than speciﬁed access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

19. You should test the sound reception every time you turn on the units or move one of the components.

20. Periodically examine all components for damage.

21. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery

monitors, cordless phones, scanners, etc.

22. Children should be supervised to ensure that they do not play with the product.

23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety. SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF and 104oF.

2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or ﬁre.

4. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach

of children (more than 3 ft (0.9m) away). Do not remove this tag.

5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit

with anything such as a towel or a blanket.

6. Other electronic products may cause interference with your baby monitor. Try installing your baby

monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.

• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding electromagnetic ﬁelds (EMF). If handled properly and according to

the instructions in this user’s manual, the product is safe to be used based on scientiﬁc evidence available today.

The RBRC® seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating

in an industry program to collect and recycle these batteries at the end of their useful lives, when taken

out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used Ni-MH batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s

involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery Recycling Corporation.

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base aﬁn de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilité du parent ou de la

personne qui s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il

continuera de fonctionner correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne

devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé.

4. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de

cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.

5. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité

Parents. N’incinérez pas les piles. Celles-ci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC®.

6. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre votre sécurité en péril.

Adaptateur de l’unité du bébé : Sortie : 6V CC 400mA

Adaptateur de l’unité du parent : Sortie : 6V CC 400mA

7. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale

ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché

dans une prise au plafond, sous une table ou dans un meuble.

8. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, aﬁn d’assurer une

accessibilité sécuritaire à la prise de courant.

9. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon

humide pour le nettoyer.

10. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.

11. Ne coupez pas les cordons d’alimentation pour remplacer les ﬁches, car ceci peut présenter un danger potentiel.

12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.

13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que

vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.

14. Ne surchargez pas les prises de courant murales ni les rallonges électriques.

15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.

16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus,

ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou

causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.

18. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du

boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous

exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.

19. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.

20. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas endommagées.

21. Soyez avisé de la perte de la conﬁdentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones sans ﬁl, des scanneurs, etc.

22. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne jouent pas avec l’appareil.

23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné sufﬁsamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source

de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, àau moins 1 mètre (3

pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)

portative avec un article tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios,

téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci

est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent

dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons aujourd’hui.

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the

Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship,

pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product

operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United

States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period

(“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without

charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we

choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will

retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive

remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces

a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or

replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you

or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal

operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service

representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna

systems; or

4. Product to the extent that the problem is caused by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed,

altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for

commercial or institutional purposes (including but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see item 2 on the following part); or

8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In

Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save

you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return

repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech

assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or

proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize

the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair

of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of

purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral

communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes

all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make

modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation. State/Provincial Law Rights: This warranty

gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten warranty

that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech

be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost proﬁts or

revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third

parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby

monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install

and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is

paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

To keep this product working well and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or

ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry before you connect them to the mains again.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part

15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely

absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to

comply with the FCC criteria. Caution: This Transmitter must be installed to provide a separation distance of at least 20cm from

all persons. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations

were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

FCC RF radiation exposure statement

Caution: This Transmitter must be installed to provide a separation distance of at least 20cm from all persons. Use of other

accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102

with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the

adapters in a cool and dry place.

Below are the questions most frequently asked about the baby monitor. If you cannot ﬁnd the answer to your question,

visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit.

2. Wait a few seconds before connecting power back to the baby units and the parent unit.

3. Turn on the baby units and the parent unit.

4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for

this to take place.

Why don’t the

power-on light of the

baby unit and parent unit

go on when I switch on

the units?

Perhaps the parent unit is not connected to the power. Insert the appliance plug into the

parent unit and put the adapter in a wall socket. Then, slide the ON/OFF to switch on

the parent unit and to establish connection with the baby unit.

Perhaps the baby unit is not connected to the power. Insert the appliance plug into the

baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to ON to

switch on the baby unit and to establish connection with the parent unit.

Why doesn’t my parent

unit charge while

connected to AC power?

Make sure the power is not controlled by a wall switch.

Why is my screen in black

and white? The screen is in black and white during night-time or in a dark room when the night

vision feature is activated. This is normal.

Why do I get glare or

blurry display on my

screen when viewing my

baby at night?

During night-time or in a dark room, the surroundings and other interfering factors,

like lightings, objects, colors and backgrounds may affect the image quality on your

parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to

prevent glare and blurry display.

Why does the baby

monitor produce a

high-pitched noise?

The parent unit and baby units may be too close to each other.

• Move the parent unit away from the baby units until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep? The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit for up to 11 hours.

The temperature of your baby’s room may be too high or too low.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

The parent unit speaker volume may be too low. Press VOL to increase the volume, or

use the parent unit menu to change sound sensitivity level to the highest level (level 5).

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

Other electronic and wireless products may cause interference with your baby monitor.

Try installing your baby monitor as far away from these devices as possible.

If you power on only one baby unit, your parent unit may display and the POWER LED

light ﬂashes. Press VIEW to switch to the baby unit you have powered on.

Frequently asked questions

The RBRC® seal For C-UL compliance only Limited warranty

California Energy Commission battery

charging testing mode

General product care

FCC and IC regulations

Storage

Important safety instructions

Parent unit overview (Con’t)

3MENU/SELECT

• Press to enter or exit the menu.

• While in a sub-menu, press to

choose

an item, or save a setting.

4Arrow keys and VOL / VOL

VOL /

• Press to increase the parent unit

speaker volume.

• While in a menu, press to scroll up,

or to enter an item’s sub-menu.

• While zooming, press and hold to

move the zoomed image upward.

VOL /

• Press to decrease the parent unit

speaker volume.

• While in a submenu, press to scroll

down.

• While zooming, press and hold

to move the zoomed image

downward.

• While in a menu, press to choose

the next item on the left.

• While zooming, press and hold to

move the zoomed image leftward.

• While in a menu, press to choose

the next item on the right.

• While zooming, press and hold to

move the zoomed image rightward.

5Microphone

6Battery indicator

• Red when battery is charging.

• Flashes red when battery is low.

7Visual sound indicators

The visual sound indicators can show

the sound level detected by the baby

unit.

Sound level detected by the baby unit

• One to three

green lights indicate a moderate

sound level detected by the baby

unit.

• Additional red

lights indicate a higher sound level

detected by the baby unit (e.g. baby

crying loudly).

8 Zoom

• Press to zoom in or out.

9LCD display

10 Speaker

11 Stand

12 ON/OFF switch

• Slide to turn on or off the parent

unit.

13 Power jack

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room.

When the baby unit being viewed detects low light levels, the infrared LEDs are switched on

automatically. The images from the baby unit are in black and white, and appears on the screen.

Notes

• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment.

• When the infrared LEDs are on, the images are in black and white. This is normal.

Tip

• Depending on the surroundings and other interfering factors, like lightings, objects, colors and

backgrounds, the display resolution may vary. Adjust the baby unit’s angle or place the baby unit at a

higher level to prevent glare and blurry display.

Your baby monitor comes ready for tabletop use. You can also choose to mount your baby monitor on

the wall. See Mount the baby unit (optional) in the Quick Start Guide for the wall mounting instructions.

Night vision

Mount the baby unit (optional)

Status icons

Connection status

• or displays when

strong signal strength is

detected between the baby

unit and the parent unit.

• or or displays when

moderate or low signal strength

is detected between the baby

unit and the parent unit.

• displays when the link

between the baby unit and

the parent unit is lost.

Patrol mode

• Displays when the parent unit is

in PATROL mode.

• For VM2251-2 only.

Current view status

• Displays the number of the

baby unit that is being viewed.

Zoom

• Displays when the current

image on the parent unit has

zoomed in.

Night vision

• Displays when the baby unit

being viewed has activated the

night vision feature.

Mute alert

• Displays when the parent unit

is talking to the baby unit.

Real-time temperature

• Displays the real-time

temperature detected by the

baby unit in Fahrenheit (oF) or

Celsius (oC) (e.g. 57

oF or 14

oC).

Battery status

• animates

when the battery is charging.

• displays solid when the

battery is fully charged.

• displays when the battery

is low and needs charging.

Speaker volume

• Displays the parent unit

speaker volume level while

adjusting.

Main menu icons

Monitoring mode

• You can enter the monitoring

mode to view the video from the

baby unit.

• For VM2251-2 only.

Brightness

• You can change the brightness of

the parent unit screen.

LCD screen off timer

• You can set a speciﬁc time to

turn the screen off.

VOX sensitivity

• With this feature, you can

choose to hear sounds from the

baby unit all the time, or to hear

sounds that exceed a certain

level. You can use the parent

unit to adjust the microphone

sensitivity of your baby unit.

The higher the sensitivity level,

the more sensitive the baby

unit is in detecting sounds for

transmitting to the parent unit.

Parent unit icons

Status icons

Main menu icons

The dim mode is to help you save the parent unit power. Your parent unit display will dim

automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert received

from the baby unit.

Notes

• While the screen is dimmed, any keypress or alert message will trigger the screen to return to the preset

brightness level. After 10 minutes of inactivity, it will dim again.

Dim mode

Sound-activated screen

• When the baby unit detects

no sound, the parent unit

screen stays off to save power.

Once a sound is detected, the

parent unit screen turns on

automatically. It will then turn

off again after 50 seconds of no

sound detection.

Temperature

• You can turn on the temperature

alert tone so that the parent

unit beeps whenever the room

temperature detected by the

baby unit falls outside of the

desired temperature range.

You can choose in Fahrenheit (oF)

or Celsius (oC) as the temperature

format displayed, or set the

maximum/minimum temperature

limit for alerts.

Warning icons and messages

/No Link to

Camera

The selected baby unit is out

of range or is turned off.

/Battery low at

Parent Unit

The battery is empty and

needs to be recharged.

/Temperature

too high

/Temperature

too low

The temperature detected by

the baby unit is higher/lower

than the desired temperature

alert range.

The parent unit is searching

for baby units.

The parent unit is connected

to AC power.

Product specificaties

Merk:	VTech
Categorie:	Babyfoon
Model:	VM2251-2

Heb je hulp nodig?

Als je hulp nodig hebt met VTech VM2251-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Babyfoon VTech

VTech RM9751 Handleiding

13 December 2024

VTech RM5754-2HD Handleiding

13 December 2024

VTech RM5764-2HD Handleiding

13 December 2024

VTech VC2105 Handleiding

13 December 2024

VTech RM2751 Handleiding

13 December 2024

VTech RM5754HD Handleiding

13 December 2024

VTech VM3252 Handleiding

16 November 2024

VTech RM5764HD Handleiding

16 November 2024

VTech DM1211 Handleiding

16 November 2024

VTech RM5766HD Handleiding

27 Februari 2024

Handleiding Babyfoon

Nieuwste handleidingen voor Babyfoon

Alecto DVM-240 BEELD Handleiding

14 November 2024

Alecto DVM-200 Handleiding

14 November 2024

Oricom SC330 Handleiding

10 December 2024

Alecto DVM200XL Handleiding

4 December 2024

D-Link DCS-825L Handleiding

23 November 2024

Chipolino Polaris Handleiding

16 November 2024

Neno Bambino Handleiding

15 November 2024

Babymoov YOO-Care A014422 Handleiding

15 November 2024

Oricom RVSL01 Handleiding

10 November 2024

Oricom RGB Handleiding

10 November 2024