VTech BM3300 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor VTech BM3300 (2 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has all the feature operations
and troubleshooting necessary to install and
operate your new VTech product. Please
review this manual thoroughly to ensure
proper installation and operation of this
innovative and feature rich VTech product.
What’s in the box
Install the battery
The parent unit runs on a rechargeable battery
or AC power. To continuously monitor your
baby, make sure you use both battery and
AC power at the same time. With the battery
alone, the parent unit can cordlessly run for a
short time only.
NOTES
Use only the battery supplied with this product.
The operating time for using the rechargeable
battery is short. If you want to monitor your baby
for a long time, we recommend you connect the
parent unit to AC power.
If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Install the battery as shown below.
NOTES
Make sure the label THIS SIDE UP is facing up
while inserting the battery.
Replace the battery
To replace the battery, pull out the battery
compartment cover, and then lift up the
battery. Follow the steps above to install the
new battery.
•
•
•
•
Connect and charge the
battery
NOTES
Use only the power adaptors supplied with this
product.
The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if they are plugged into a ceiling, under-the-table
or cabinet outlet.
Make sure the parent unit, the baby unit and
the power adaptor cords are out of the reach of
children.
Connect the baby monitor
•
•
•
Charge the parent unit battery
When you have connected the parent unit and
installed its battery for the first time or after
power outage, the parent unit will power on
automatically. The battery icon indicates the
battery status (see the following table).
NOTES
The parent unit battery is fully charged after
11 hours of continuous charging.
It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
The standby time varies depending on the
volume level you set, your actual use and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off
and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge
without
interruption
(at least
30 minutes).
The screen
displays
Battery low
at Parent
Unit and .
The lightlight
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about
30 minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
•
•
•
Before use
NOTES
This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You should test the baby monitor before initial
use, and at regular times thereafter.
CAUTION
For hearing protection, make sure the
parent unit is more than 1 metre (3 feet)
away from the baby unit. If you hear any
high-pitched noise, move the parent unit
further away until the noise stops. You can
also press VOL- on the parent unit to lower
or mute the noise.
Make sure your baby unit and parent unit
are on.
The parent unit displays images from the
baby unit.
Speak towards the microphone of the
baby unit. You will hear the sound at the
parent unit.
NOTES
When the parent unit displays No link to
Camera, and the LINK LED light flash, move the
parent unit closer to the baby unit (observe the
minimum distance of 1 metre/ 3 feet). You can
also check if the baby monitor is connected to a
live power socket and switched on.
TIP
Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
•
•
1.
2.
•
•
•
Positioning the baby monitor
CAUTION
Keep the baby unit out of the reach of your baby.
Never place or mount the baby unit inside the
baby’s cot or playpen.
NOTE
To avoid interference from other electronic
devices, place your baby monitor far away from
devices such as wireless routers, microwaves,
mobile phones and computers.
Place the baby unit more than 1 metre
(3 feet) away from your baby.
Place the parent unit more than 1 metre
(3 feet) away from the baby unit.
3. Flip down the camera on the baby unit
to adjust the angle according to your
preference.
CAUTION
The default volume of your parent unit is level 4.
If you experience high-pitched screeching noise
from your baby monitor while positioning:
Make sure your baby unit and parent unit are
more than 1 metre (3 feet) apart, OR
Turn down the volume of your parent unit.
•
•
1.
2.
•
-
-
Operating range
The operating range of the baby monitor is
up to 300 metres (1,000 feet) outdoors or
50 metres (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Overview
Baby unit overview
1Light sensor
2Camera
3Infrared LEDs
4-/VOLUME/+
Press to adjust the speaker volume.
It determines the talkback volume
transmitted from your parent unit.
•
5Microphone
6ON/OFF LED light
On when the baby unit is turned on
and is paired to the parent unit.
Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
•
•
7 ON/OFF switch
Slide to turn the baby unit on or off.•
8Temperature sensor
9Speaker
10 Threaded socket
For wall mount installation use.•
11 Power Jack
12 PAIR
Your baby unit and parent unit
provided are already paired.
•
Parent unit overview
1 LCD display
2 Zoom
Press to zoom in or out while
viewing images.
•
3
4
• Turn the volume up when the
speaker is on.
While in a menu, press to scroll up,
or to enter an item’s sub-menu.
While zooming, press and hold to
move the zoomed image up.
• Turn the volume down when the
speaker is on.
While in a menu, press to scroll
down.
While zooming, press and hold to
move the zoomed image down.
•
•
•
•
5MENU/SELECT
Press to enter/exit the menu.
While in a sub-menu, press to
choose an item, or save a setting.
•
•
6
While in a menu, press to choose
the next item on the left, or enter
into the submenu, if any.
While zooming, press and hold to
move the zoomed image to the left.
While in a menu, press to choose
the next item on the right, or return
to the main menu while in submenu.
While zooming, press and hold to
move the zoomed image to the
right.
•
•
•
•
7 On/off
Press and hold to power on.
Press and hold again to power off.
•
•
8TALK
Press and hold to talk to the baby
unit.
•
9PATROL
10 LCD ON/OFF
Press to turn the LCD screen on or
off.
•
11 Speaker
12 Power jack
13 Battery compartment cover
14 Stand
Parent unit lights
LINK On when the parent unit is linked to
the baby unit.
Flashes quickly when the link to the
baby unit is nearly lost.
On when the parent unit is
connected to AC power, or the
battery is charging.
Flashes when the parent unit
battery is low and needs charging.
Off when the parent unit is
disconnected from AC power.
TALK On when the parent unit is talking to
the baby unit.
On when the speaker volume of the
parent unit is turned off.
Parent unit status icons
Connection status
or displays when strong
signal strength is detected
between the baby unit and the
parent unit.
or displays when moderate
or low signal strength is detected
between the baby unit and the
parent unit.
displays when the link between
the baby unit and the parent unit
is lost.
•
•
•
Zoom
Displays when the camera at the
baby unit has zoomed in.
•
Night vision
Displays when the baby unit has
activated the night vision feature.
•
Lullaby
Displays when a lullaby is playing.•
Talkback
Displays when talking back to the
baby unit from the parent unit.
•
6-level sound indicator
Displays the sound level when there
is sound transmitted from the baby
unit.
(1 to 2 bars) indicates low sound
level detected by the baby unit.
(3 to 4 bars) indicates
moderate sound level detected by
the baby unit.
(5 to 6 bars) indicates high
sound level detected by the baby
unit (e.g. baby crying loudly).
•
•
•
Mute alert
Displays when the parent unit
speaker volume is set to off.
•
or
Real-time temperature
Displays the real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57
oF or 14
oC).
•
Battery status
animates
when the battery is charging.
displays solid when the
battery is fully charged.
displays when the battery is
low and needs charging.
•
•
•
AC power without battery
Displays when the parent unit is
connected to AC power without
the battery.
•
Speaker volume
Displays the parent unit speaker
volume level while adjusting.
•
Parent unit main menu icons
Brightness
You can change the brightness of
the parent unit screen.
Pairing baby unit
The baby unit and parent unit
provided are already paired.
Unpairing baby unit
You can remove the paired baby
unit.
LCD screen off timer
You can set a specific time for the
parent unit screen to switch off.
Temperature
You can turn on the Temperature
alert tone on so that the parent
unit beeps whenever the room
temperature detected by the
baby unit falls outside the desired
temperature range.
Lullaby
You can select, play, or stop a
lullaby.
Parent unit warning icons and
messages
/No link to
Camera
The baby unit is out of
range or is turned off.
/Battery low
at Parent Unit
The battery is empty and
needs to be recharged.
Pairing or unpairing is
complete.
Pairing or unpairing is in
progress.
Pairing or unpairing has
failed.
/Temperature
too high
or
/Temperature
too low
The temperature
detected by the baby unit
is higher/lower than the
desired temperature alert
range.
or or
or
or
The baby unit is unpairing
from the parent unit.
The parent unit is
searching for baby unit.
BC
User’s manual
BM3300
Safe & Sound®
2.8” Colour
Video Baby Monitor
For product support please call
01235 546810
> 1m (3ft)
b
c
d
e
m
n
k
j
i
l
a
h
g
f
DC 6V 500mA
MANUFACTURED IN CHINA
www.vtechphones.com
VTech Customer Service
1-800-595-9511
FCC ID: EW780-0617-00
IC: 1135B-80061700
4H20
I.T.E.
PAIR
e
d
a
b
c
h
i
f
g
j
k
l
＜1m (3ft)
＞1m (3ft)
THIS SIDE UP
THIS SIDE UP
> 1m (3ft)
Using the baby monitor
Power the baby unit on or off
Slide the ON/OFF switch up to turn the
baby unit on. The ON/OFF LED light turns
on.
Slide the ON/OFF switch down to turn
the baby unit off. The ON/OFF LED light
turns off.
Power the parent unit on or off
Press and hold to turn the parent unit on.
The screen turns on.
Press and hold again to turn the parent
unit off. The screen turns off.
Turn the parent unit screen on
or off
You can turn the parent unit screen on or off
without switching the parent unit off. You can
still hear sound from the baby unit.
Press LCD ON/OFF on the parent unit to
turn the screen off.
Press any key on the parent unit to turn the
screen on again.
Adjust speaker volume
For parent unit:
Press VOL+/VOL- on the parent unit to
adjust the speaker volume.
NOTE
When the parent unit speaker volume is set to
zero, appears on the screen and the light
turns on.
For baby unit:
The baby unit speaker volume determines the
talkback volume transmitted from your parent
unit.
Press +/VOLUME/- on the baby unit to
adjust the speaker volume.
•
•
•
•
•
•
•
•
•
Adjust LCD brightness
You can change the brightness of the parent
unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
Press MENU when the parent unit is idle.
Press or to choose , then press .
Press or to choose the desired level of
brightness, then press SELECT to confirm
your selection.
Zoom
You can zoom in while viewing images from
the baby unit.
Press to zoom in.
Press or to move the zoomed image
up or down.
Press or to move the zoomed image
left or right.
Press again to zoom out.
Talk
You can use the TALK function on the parent
unit to comfort your baby.
Press and hold TALK on the parent unit.
The TALK light turns on.
Speak towards the microphone on the
parent unit. Your voice is broadcast to the
baby unit.
Release the TALK key to stop the
broadcast. The TALK light goes off.
1.
2.
3.
•
•
•
•
1.
2.
3.
Lullaby
You can play the lullabies on the baby unit
from the parent unit. On the baby unit, you can
control the volume level of the lullabies.
Playing lullabies
Press MENU when the parent unit is idle.
Press or to choose , then press .
Press or to choose a lullaby, or choose
to stop playing.
Press SELECT to confirm your selection.
Volume level control on baby unit
Press VOL+ to increase the volume level of
the lullaby on the baby unit.
Press VOL- to decrease the volume level of
the lullaby on the baby unit.
NOTE
The lullaby will stop when you start using the
TALK function on the parent unit to comfort your
baby.
1.
2.
3.
4.
•
•
•
Monitor the temperature
Your baby unit monitors the temperature of
your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the
preset temperature range, the parent unit will
display an alert message.
Set temperature range
You can set the desired room temperature
alert range. The minimum temperature can be
set between 50 oF (10 oC) and 76 oF (24 oC).
The maximum temperature can be set
between 77 oF (25 oC) and 102 oF (39 oC).
Press MENU when the parent unit is idle.
Press or to choose , then press .
Press or to choose , then press
SELECT.
Press or to choose or , then
press SELECT.
Press or to choose the desired
minimum or maximum temperature, then
press SELECT to confirm your selection.
Temperature alert tone
You can turn the temperature alert tone on so
that the parent unit will emit an alert tone if the
detected temperature is out of range.
Press MENU when the parent unit is idle.
Press or to choose , then press .
Press or to choose , then press
SELECT.
Press or to choose or , then
press SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in
Fahrenheit (oF) or Celsius (oC).
Press MENU when the parent unit is idle.
Press or to choose , then press .
Press or to choose , then press
SELECT.
Press or to choose or , then
press SELECT to confirm your selection.
1.
2.
3.
4.
5.
1.
2.
3.
4.
1.
2.
3.
4.
General product care
To keep this product working well and looking good,
follow these guidelines:
Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the baby
unit in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from
the parent unit. Store the parent unit, the baby unit
and the adaptors in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtech.co.uk, or
contact 01235 546810 for customer service.
Why does
the baby
monitor not
respond
normally?
Try the following (in the order
listed) for a common cure:
1. Disconnect the power to the
baby unit and the parent unit.
2. Remove the batteries in the
parent unit. Then install the
batteries again.
3. Wait a few seconds before
connecting power back to the
baby unit and the parent unit.
4. Turn the baby units and the
parent unit on.on..
5. Wait for the parent unit to
synchronise with the baby unit.
Allow up to one minute for this to
take place.
•
•
•
•
•
•
•
Why don’t
the power-on
lights on the
baby unit or
the parent
unit go on
when I switch
the units on?
Perhaps the parent unit is not
connected to the power. Insert
the appliance plug into the parent
unit and put the adaptor in a wall
socket. Then press and hold to
switch the parent unit on and to
establish connection with the baby
unit.
Perhaps the baby unit is not
connected to the power. Insert
the appliance plug into the baby
unit and put the adaptor in a wall
socket. Then slide the ON/OFF
switch to ON to switch the baby
unit on and to establish connection
with the parent unit.
Why doesn’t
my parent
unit charge
while
connected to
AC power?
Make sure the battery is installed.
You may have used the battery for
a long time. Replace with a new
battery.
Why is my
screen in
black and
white?
The screen is in black and white
during night-time or in a dark room
when the night vision feature is
activated. This is normal due to
external light sources.
Why do I get
glare or a
blurry display
on my screen
when viewing
my baby at
night?
During night-time or in a dark
room, the surroundings and other
interfering factors, like lights,
objects, colours and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and a blurry display.
Why does
the baby
monitor
produce a
high-pitched
noise?
The parent unit and baby unit may
be too close to each other.
Move the parent unit away from
the baby unit until the noise
stops; OR
Turn down the volume of your
parent unit.
•
•
Why does
the parent
unit beep?
The baby unit may be out of
range. Move the parent unit closer
to the baby unit (but not less than
3 feet).
If the parent unit is powered by the
provided battery, it may not have
enough charge for the parent unit to
perform normally. Charge the battery
in the parent unit for up to 11 hours.
The temperature of your baby’s
room may be too high or too low.
The ON/OFF
light on the
baby unit
flashes and
the parent
unit displays
.
Follow below steps to pair the
baby unit. Make sure both parent
unit and baby unit are on before
pairing.
Press MENU when the parent
unit is idle.
Press or to choose ,
then press to select.
Press or to choose an
empty baby unit slot, then
press SELECT. The parent unit
screen displays .
Use a narrow-pointed object,
such as a pen, to press PAIR
on the bottom of the baby unit.
The ON/OFF LED light at
the side of baby unit flashes
quickly when pairing.
When pairing is successful, the
parent unit screen displays and
the LINK light turns on. The view
of the newly paired baby unit will
be shown on the parent unit. The
ON/OFF LED light on the baby
unit remains on.
If pairing fails, the screen
displays . Try the pairing
process again.
1.
2.
3.
4.
•
•
I have
accidentally
unpaired my
baby unit.
Why don’t
I hear a
sound/Why
can’t I hear
my baby cry?
The parent unit speaker volume
may be too low or off. Press VOL+
to increase the volume.
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why
are there
sound
interruptions?
The baby unit may be out of
range. Move the parent unit closer
to the baby unit (but not less than
3 feet).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Important safety instructions
When using your equipment, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and
injury, including the following:
Follow all warnings and instructions marked on
the product.
Adult setup is required.
This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
This product is not intended for use as a medical
monitor.
Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in
a wet basement or shower.
CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion if a
wrong type of battery is used for the parent unit.
Use only the supplied rechargeable battery for
the parent unit. Do not dispose of batteries in a
fire. They may explode. Dispose of used battery
according to the information in The RBRC® seal.
Use only the adaptors included with this
product. Incorrect adaptor polarity or voltage can
seriously damage the product.
Baby unit power adaptor: Output: 6V DC 500mA
Parent unit power adaptor: Output: 6V DC 500mA.
The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
Unplug the power cords before replacing
batteries.
Do not cut off the power adaptors to replace
them with other plugs, as this causes a
hazardous situation.
Do not allow anything to rest on the power cords.
Do not install this product where the cords may
be walked on or crimped.
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
Do not overload wall outlets or use an extension
cord.
Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or
heat register.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorised service facility. Opening or removing
parts of the product other than specified
access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling
can cause electric shock when the product is
subsequently used.
You should test the sound reception every
time you turn on the units or move one of the
components.
Periodically examine all components for
damage.
Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
Children should be supervised to ensure that
they do not play with the product.
The product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
SAVE THESE INSTRUCTIONS
17.
18.
19.
20.
21.
22.
23.
Cautions
Use and store the product at a temperature
between 0oC and 40oC.
Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
Batteries should not be exposed to excessive
heat such as bright sunshine or fire.
Warning—Strangulation
Hazard— Keep this cord out
of the reach of children (more
than 3 ft (0.9 m) away). Do not
remove this tag.
Never place the baby unit
inside the baby’s cot or
playpen. Never cover the baby unit or parent unit
with anything such as a towel or a blanket.
6. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, mobile telephones,
intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
1.
2.
3.
4.
5.
Customer service and
product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on
01235 546810 (from UK) or +44 1235 546810
(outside UK) and a service representative will be
happy to help you.
This warranty is valid for the UK and Eire only. For products purchased outside
the UK and Eire, please contact your local distributor or place of purchase.
PRODUCT WARRANTY
PRODUCT REGISTRATION
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR Thank you for choosing this quality product from VTech.
We hope it will bring many hours of entertainment,
imaginative play and learning.
1. The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2. The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3. VTech Electronics Europe plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4. If the product covered by this warranty is damaged due to misuse, modification or
unauthorised repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.
6. Breakages to the LCD screen are not covered by the warranty.
7. Returns to VTech Electronics Europe plc should include a cheque or postal order for
£1.50 towards the cost of return postage and packaging.
8. Products returned to VTech Electronics Europe plc, should be addressed as follows and
packed carefully to avoid damage in transit (Please do not include batteries or adaptor).
Please include details of the fault together with your name and address.
9. To keep an online record of your warranty, please register your product online at www.
vtech.co.uk/warranty
Vtech Electronics EU PLC, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane, West
Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions, find
out about news and events, seek expert advice for parents and
let your kids play fun learning games and activities.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
Maximum
RF power
20dBm
LCD 2.8” Colour LCD
(WQVGA 320x240 pixel)
Nominal
effective
range
Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Parent unit: 3.6V Ni-MH battery
Baby unit power adaptor:
Output: 6V DC @ 500mA
Parent unit power adaptor:
Output: 6V DC @ 500mA
Disposal of batteries and
product
The crossed-out wheelie bin symbols
on products and batteries, or on their
respective packaging, indicates they
must not be disposed of in domestic
waste as they contain substances
that can be damaging to the
environment and human health.
The chemical symbols Hg, Cd or
Pb, where marked, indicate that
the battery contains more than the
specified value of mercury (Hg),
cadmium (Cd) or lead (Pn) set out in
Battery Directive (2006/66/EC).
The solid bar indicates that the
product was placed on the market
after 13th August, 2005.
Help protect the environment by
disposing of your product or batteries
responsibly.
Declaration of Conformity
This product is intended for use within Europe.
Vtech Telecommunications Ltd hereby declares that
this model Safe & Sound® 2.8” Colour Video Baby
Monitor BM3300 is in compliance with the essential
requirements and other relevant provisions of
Directives: 1999/5/EC or 2014/53/EU.
The declaration of conformity for the BM3300 is
available at website http://www.vtech.com/rtte-directive.
Specifications are subject to change without notice.
© 2017 VTech Communications, Inc.
All rights reserved. 05/17. BM3300_UK_CIB_V1
Manufactured by VTech Telecommunications Ltd.
VTech Electronics Europe Plc, Napier Court,
Abingdon Science Park, Abingdon, Oxon, OX14 3YT.
Product specificaties
| Merk: | VTech |
| Categorie: | Babyfoon |
| Model: | BM3300 |
Heb je hulp nodig?
Als je hulp nodig hebt met VTech BM3300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Babyfoon VTech
6 Januari 2025
13 December 2024
13 December 2024
13 December 2024
13 December 2024
13 December 2024
13 December 2024
16 November 2024
16 November 2024
16 November 2024
Handleiding Babyfoon
- Babyfoon Philips
- Babyfoon IKEA
- Babyfoon Brondi
- Babyfoon Fysic
- Babyfoon Grundig
- Babyfoon Gigaset
- Babyfoon Motorola
- Babyfoon Medion
- Babyfoon Tefal
- Babyfoon Topcom
- Babyfoon Albrecht
- Babyfoon Alcatel
- Babyfoon Alecto
- Babyfoon Amplicomms
- Babyfoon Angelcare
- Babyfoon Ansmann
- Babyfoon Ariete
- Babyfoon Audioline
- Babyfoon Babyfon
- Babyfoon Babymoov
- Babyfoon BabySafe
- Babyfoon Basetech
- Babyfoon Beaba
- Babyfoon Bebetel
- Babyfoon Beurer
- Babyfoon Binatone
- Babyfoon BT
- Babyfoon D-Link
- Babyfoon Denver
- Babyfoon Duronic
- Babyfoon Duux
- Babyfoon Elro
- Babyfoon Esscom
- Babyfoon Eufy
- Babyfoon Ezviz
- Babyfoon Fischer Price
- Babyfoon Fisher Price
- Babyfoon Foscam
- Babyfoon Geemarc
- Babyfoon Goclever
- Babyfoon Graco
- Babyfoon Grixx
- Babyfoon Hama
- Babyfoon Hartig Helling
- Babyfoon HQ
- Babyfoon Hyundai
- Babyfoon Kodak
- Babyfoon Kogan
- Babyfoon Konig
- Babyfoon Lanaform
- Babyfoon Lorex
- Babyfoon Lupilu
- Babyfoon Luvion
- Babyfoon Manhattan
- Babyfoon ME
- Babyfoon Medisana
- Babyfoon MicroTalk
- Babyfoon Modern-Electronics
- Babyfoon Nedis
- Babyfoon Nova
- Babyfoon Pabobo
- Babyfoon Philips-Avent
- Babyfoon Reer
- Babyfoon Safety 1st
- Babyfoon Sanitas
- Babyfoon Silvercrest
- Babyfoon Stabo
- Babyfoon Swissvoice
- Babyfoon Switel
- Babyfoon Technaxx
- Babyfoon Terraillon
- Babyfoon Tesla
- Babyfoon Tommee Tippee
- Babyfoon Tomy
- Babyfoon Trebs
- Babyfoon Trendnet
- Babyfoon Tristar
- Babyfoon Truelife
- Babyfoon Uniden
- Babyfoon Withings
- Babyfoon Jablotron
- Babyfoon Jane
- Babyfoon Olympia
- Babyfoon Oregon Scientific
- Babyfoon Oretti
- Babyfoon Overmax
- Babyfoon Concept
- Babyfoon Niceboy
- Babyfoon Lionelo
- Babyfoon Cobra
- Babyfoon EMOS
- Babyfoon Chicco
- Babyfoon Cresta
- Babyfoon SereneLife
- Babyfoon M-e
- Babyfoon Hartig And Helling
- Babyfoon NUK
- Babyfoon Oricom
- Babyfoon Summer
- Babyfoon Tigex
- Babyfoon Lindam
- Babyfoon BabyOno
- Babyfoon Neno
- Babyfoon Xblitz
- Babyfoon Comtel
- Babyfoon IBaby
- Babyfoon Levana
- Babyfoon Mobi
- Babyfoon Neonate
- Babyfoon Chipolino
- Babyfoon Babysense
- Babyfoon Heimvision
- Babyfoon Summer Infant
- Babyfoon LeamsiQ
- Babyfoon British Telecom
- Babyfoon Chillax Baby
- Babyfoon Hubble Connected
- Babyfoon Peekyboo
Nieuwste handleidingen voor Babyfoon
18 Februari 2025
18 Februari 2025
British Telecom Digital Baby Monitor 350 Lightshow Handleiding
18 Februari 2025
11 Februari 2025
10 Februari 2025
25 Januari 2025
25 Januari 2025
25 Januari 2025
14 Januari 2025
30 December 2025