VTech BM1000 Babyfoon Handleiding

VTech Babyfoon BM1000 Babyfoon

Lees hieronder de 📖 handleiding in het Nederlandse voor VTech BM1000 Babyfoon (2 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Note

• This baby monitor should be for use by adults only.

• It is not a substitute for proper adult supervision, and should not be used as such.

Test your baby monitor

You may test the baby monitor before initial use,

and at regular times thereafter.

Caution

• For hearing protection, make sure the parent unit is

more than 1 metre away from the baby unit. If you

hear any feedback, move the parent unit further

until the noise stops. You can also press on the

parent unit to lower or mute the noise.

1. Make sure your baby unit and parent unit are

on.

2. Speak towards the microphone of the baby unit. You will hear the sound at the parent unit,

and see the visual sound indicators light up.

Note

• When the POWER LED light ﬂashes, move the parent unit closer to the baby unit (observe the

minimum distance of 1 metre). You can also check if the baby unit is connected to a live power

socket and switched on.

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the

baby unit.

Positioning the baby monitor

Caution

• Keep the baby unit out of the reach of your baby. Never place or

mount the baby unit inside the baby’s cot or playpen.

1. Place the baby units more than 1 metre away from your

baby.

2. Place the parent unit more than 1 metre away from the baby

unit to avoid feedback.

Caution

• The default volume of your parent unit is level 3, and the

maximum volume is level 5. If you experience feedback from

your baby monitor while positioning:

- Make sure your baby units and parent unit are more than

1 metre apart, OR

- Turn down the volume of your parent unit.

User’s manual

BM1000

Digital Audio Monitor

Connect

What’s in the box

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 1881.792 - 1897.344 MHz

Parent unit: 1881.792 - 1897.344 MHz

Maximum power used by the transmitter: 0.25W (250mW)

Channels 120

Nominal effective range Actual operating range may vary according to environmental

conditions at the time of use.

Power requirements Baby unit adaptor: Output: 6V DC @ 450mA

Parent unit adaptor: Output: 6V DC @ 450mA

Parent unit battery: 2 x 1.2V AAA size 400mAh NiMH

Technical speciﬁcations

Speciﬁcations are subject to change without notice.

POWER

> 3ft (1m)

CHARGING

POWER

CHARGING

> 1 metre

1 metre

POWER

> 1 metre

> 3ft (1m)

1 metre

POWER

CHARGING

CHARGI NG

Power on or off the baby unit

• Press and hold to turn on the baby unit. The POWER LED

light turns on.

• Press and hold again to turn off the baby unit. The POWER

LED light turns off.

Power on or off the parent unit

• Press and hold to turn on the parent unit. The POWER LED

light turns on.

• Press and hold again to turn off the parent unit. The

POWER LED light turns off.

Adjust parent unit speaker volume

The speaker volume is preset to level 3, and the maximum

volume is level 5. You can adjust it to your preferred volume

level.

• Press or on the parent unit to adjust the speaker volume.

Note

• If you continue to press or when the volume reaches the minimum

or maximum setting, the parent unit will beep twice.

To mute the speaker volume:

• Press repeatedly until the volume reaches the minimum.

Notes

• When the parent unit is in mute, the visual sound indicator will still

indicate the sound detected from the baby unit.

• To unmute, press repeatedly until it reaches your desired volume.

POWER POWER

CHARGINGCHARGING

CHARGING

2 Before use 3 Using the baby monitor

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety

instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

Important safety instructions

The applied nameplate is located at the bottom of the baby

unit’s base.

When using your equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric

shock and injury, including the following:

1. Follow all warnings and instructions marked on the

product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above

2 metres.

4. This product is not a substitute for adult supervision of

the infant. Supervising the infant is the responsibility

of the parent or carer. This product could cease

operating, and therefore you should not assume it will

continue working properly for any given period of

time. Further, this is not a medical device and should

not be used as such. This product is intended to assist

you in supervising your baby.

5. Do not use this product near water, for example, near

to a bath, sink, swimming pool or shower.

6. CAUTION: Use only the battery provided. There

may be a risk of explosion if a wrong type of battery

is used for the parent unit. The battery cannot be

subjected to high or low extreme temperature and

low air pressure at high altitude during use, storage

or transportation. Disposal of battery into ﬁre or a hot

oven, or mechanically crushing or cutting or the battery

can result in an explosion. Leaving the battery in an

extremely high temperature surrounding environment

can result in an explosion or the leakage of ﬂammable

liquid of gas. Battery subjected to extremely low air

pressure may result in an explosion or the leakage

of ﬂammable liquid or gas. Dispose of used battery

according to the instructions.

7. Use only the adaptors included with this product.

Incorrect adaptor polarity or voltage can seriously

damage the product.

Power adaptor information:

Output: 6V DC 450mA

Ten Pao Industrial Co.,Ltd.

Model: S003ATV0600045(EU), S003ATB0600045 (UK).

Rechargeable battery information:

2 x 1.2V AAA size 400mAh NiMH

Corun : NiMH AAA 400mAh 1.2V

8. The power adaptors are intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place if it

is plugged into a ceiling, under-the-table or cabinet

outlet.

9. For pluggable equipment, the socket-outlet should

be installed near the equipment and should be easily

accessible.

10. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

11. Unplug the power cords before replacing battery.

12. Do not cut off the power adaptors to replace them with

other plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do

not install this product where the cords may be walked

on or crimped.

14. This product should be operated only from the type

of power source indicated on the marking label. If you

are not sure of the type of power supply in your home,

consult your dealer or local power company.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf,

stand or other unstable surfaces.

17. This product should not be placed in any area where

proper ventilation is not provided. Slots and openings

in the back or bottom of this product are provided for

ventilation. To protect them from overheating, these

openings must not be blocked by placing the product

on a soft surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or heat

source.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage

points or create a short circuit. Never spill liquid of any

kind on the product.

19. To reduce the risk of electric shock, do not

disassemble this product, but take it to an authorized

service facility. Opening or removing parts of the

product other than speciﬁed access doors may

expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when

the product is subsequently used.

20. You should test the sound reception every time you turn

on the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using

certain electronic devices, such as baby monitors,

cordless telephones, etc. To protect your privacy,

make sure the product has never been used before

purchase, reset the baby monitor periodically by

powering off and then powering on the units, and

power off the baby monitor if you will not use it for

some time.

23. Children should be supervised to ensure that they do

not play with the product.

24. The product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between

0oC and 40oC.

2. Do not expose the product to extreme cold, heat or

direct sunlight. Do not put the product close to a heating

source.

3. Batteries should not be exposed to

excessive heat such as bright sunshine or

ﬁre.

4. Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out of

the reach of children (more than 3 ft (0.9m) away).

Do not remove this tag.

5. Never place the baby unit(s) inside the baby’s cot or

playpen. Never cover the baby unit(s) or parent unit with

anything such as a towel or a blanket.

6. Other electronic products may cause interference

with your baby monitor. Try installing your baby

monitor as far away from these electronic devices

as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless

telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and

implanted cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to physicians

that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned

ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and

according to the instructions in this user’s manual, the

product is safe to be used based on scientiﬁc evidence

available today.

User’s

manual

Install the parent unit battery

The package comes with two rechargeable batteries. You

can power up the parent unit by using the two rechargeable

batteries or by connecting it to the mains power. However,

even if the parent unit is connected to the mains power, we

recommend that you also install the rechargeable batteries. This

guarantees the continual operation in case of a power outage.

NOTESNOTE

• Use only the batteries supplied with this product.

• If the parent unit will not be used for a long time, disconnect and

remove the batteries to prevent possible leakage.

1. Remove the battery compartment cover.

2. Install the supplied rechargeable batteries into the battery

compartment, matching the polarity markings (+ and -).

3. Close the battery compartment cover.

Connect the baby monitor

NOTESNOTE

• Use only the power adaptors supplied with this product.

• Make sure the baby monitor is not connected to a switch controlled electric outlet.

• Connect the power adaptors in a vertical or ﬂoor mount position only. The adaptors’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adaptor cords are out of reach of children.

• With audio reminder feature preset to on, the parent unit plays an audio reminder when it is

connected to a baby unit.

POWER

CH AR GI NG

To keep this product working well and looking good, follow these guidelines:

• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or

ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft damp cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry before you connect them to the mains again.

When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the

adaptors in a cool and dry place.

Below are the questions most frequently asked about the baby monitor.

Why doesn’t the POWER

light on the baby unit turn on

when I switch on the units?

Perhaps the baby unit is not connected to the power supply. Connect the baby unit to

power supply. The baby unit turns on.

Why doesn’t the POWER

light on the parent unit

turn on when I switch on

the units?

Perhaps the batteries of the parent unit are depleted and the parent unit is not connected

to power supply. Connect the parent unit to power supply and charge the parent unit’s

batteries. The parent unit turns on and establishes connection with the baby unit.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby unit and the parent unit.

2. Remove the batteries from the parent unit.

3. Connect the baby unit to the power supply again. The baby unit turns on.

4. Connect the parent unit to the power supply again. The parent unit turns on.

5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for

this to take place.

6. Press or to adjust the speaker volume on the parent unit.

Why does the baby

monitor produce a

feedback?

The parent unit and baby unit may be too close to each other.

• Move the parent unit away from the baby unit until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep?

The parent unit beeps three times every 30 seconds when the baby unit is out of range.

Move the parent units closer to the baby unit (but not less than 1 metre).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit for at least 30 minutes.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

Make sure that both baby unit and parent unit are on. If you see the visual sound indicators

light up, but there is no sound, then you may have muted the volume or set it to a lower

level. Adjust the volume to a higher level.

If the visual sound indicators do not light up, and you cannot hear any sound, it is because

the sound is too low for the baby unit to detect. This is normal. Place the baby unit at least

1 metre away from your baby.

Why does the CHARGING

light on the parent unit

ﬂash?

If the parent unit is powered by batteries, the parent unit beeps twice every 10 minutes

and the CHARGING light ﬂashes in red when the battery is low. Connect the parent unit

to the power supply and charge the battery for at least 30 minutes.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby unit may be out of range. Move the parent units closer to the baby unit (but not

less than 1 metre).

Other electronic products may cause interference with your baby monitor. Try installing

your baby monitor as far away from these electronic devices as possible.

Frequently asked questions

General product care

Storage

1POWER light

• On when the baby unit is

powered up.

• Flashes when the link to the

parent unit is lost.

2 (On/off)

• Press and hold to turn on or off

the baby unit.

3Microphone

4Power jack

Parent unit overview

CHARGING

POWER

1Visual sound indicators

The visual sound indicators can show

the sound level detected by the

baby unit or the volume level during

speaker volume setting.

Sound level detected by the baby

unit

•

One to three green lights indicate

a moderate sound level detected

by the baby unit.

•

Additional red lights indicate a

higher sound level detected by

the baby unit (e.g. baby crying

loudly).

Speaker volume level

•

One to three green lights indicate

Level 1 to Level 3 of the speaker

volume setting.

•

Additional red lights indicate Level

4 to Level 5 of the speake volume

setting.

2POWER

• Lights on steadily in green when

the parent unit is on and linked to

the baby unit.

• Flashes in green when there is no

link between the baby unit and

parent unit, or when the parent unit

is out of range from the baby unit.

3CHARGING

• Steady on in red when the parent

unit is charging.

• Flashes in red when the battery is

low.

4 (Volume down)

• Press to decrease the parent unit

speaker volume.

5 (On/off)

• Press and hold to turn on or off the

parent unit.

6Speaker

7Belt clip

8 (Volume up)

• Press to increase the parent unit

speaker volume.

9Battery compartment cover

10 Power jack

Parent unit alert tones

Low battery tone • Beeps twice every 10 minutes when the battery is low.

Out of range tone • Beeps three times every 30 seconds when there is no link

between the baby unit and parent unit, or when the parent

unit is out of range from the baby unit.

Baby unit overview

CHARGING

POWER

IMPORTANT

Please retain this booklet with your

sales receipt as proof of the date of

purchase.

Customer Service

Please call our Consumer Services

Department on 03306 780149 (from

UK) or +44 3306 780149 (outside UK)

and a service representative will be

happy to help you.

Customer service and product warranty

The crossed-out wheelie bin symbols on products and batteries, or on their respective

packaging, indicates they must not be disposed of in domestic waste as they contain

substances that can be damaging to the environment and human health.

The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains

more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery

Directive (2006/66/EC).

The solid bar indicates that the product was placed on the market after 13th August, 2005.

Help protect the environment by disposing of your product or batteries responsibly.

Disposal of batteries and product

This product is intended for use within Europe and UK.

This equipment complies with the essential requirements to EU’s Radio Equipment

Directive (2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and

telecommunication equipment.

Vtech Telecommunications Ltd. hereby declares that

this Audio Monitor BM1000 is in compliance with the essential requirements and other

relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio

Equipment Regulations 2017.

The Declaration of Conformity for the BM1000 is available from

www.vtechbabycare.com.

Declaration of Conformity

This warranty is valid for the UK and Ireland only. For products purchased outside

the UK and Ireland, please contact your local distributor or place of purchase.

ONE

YEAR

PRODUCT WARRANTY

Thank you for choosing this quality product from VTech.

1.The product detailed above is covered by a one year warranty from the date of purchase,

against any defects in materials or workmanship.

2.The product may be returned to the place of purchase. Alternatively the product can be

returned to VTech Electronics Europe Plc (see address below), with proof of purchase,

without proof of purchase no replacement will be provided.

3.VTech Electronics Europe Plc will examine the product and if it is found to be defective

due to faulty materials or workmanship, will replace the product at their discretion.

4.If the product covered by this warranty is damaged due to misuse, modification or

unauthorized repair, or because of faulty batteries, battery discharge or incorrect

electrical connections, then this warranty becomes void.

5.This warranty is personal to the original purchaser and is not transferable.

6.Breakages to the LCD screen are not covered by the warranty.

7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown

below and packed carefully to avoid damage in transit. Please do not include batteries or

adaptors. Please include details of the fault together with your name and address,

contact phone number and/or email address.

8.To keep an online record of your warranty, please register your product online at

www.vtech.co.uk/clubvtech

VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,

West Hallam, DE7 6HE

THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT

CONSUMERS’ STATUTORY RIGHTS.

PRODUCT REGISTRATION

Visit www.vtech.co.uk/clubvtech/login

to register your VTech product

By joining the VTech Club you can also enter competitions,

find out about news and events, seek expert advice for parents

and let your kids play fun learning games and activities.

Manufacturer: VTech Telecommunications Ltd.

23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.

Importer: VTech Electronics Europe Plc

Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.

Product specificaties

Merk:	VTech
Categorie:	Babyfoon
Model:	BM1000 Babyfoon

Heb je hulp nodig?

Als je hulp nodig hebt met VTech BM1000 Babyfoon stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Babyfoon VTech

VTech RM7756HD Handleiding

6 Januari 2025

VTech RM9751 Handleiding

13 December 2024

VTech RM5754-2HD Handleiding

13 December 2024

VTech RM5764-2HD Handleiding

13 December 2024

VTech VC2105 Handleiding

13 December 2024

VTech RM2751 Handleiding

13 December 2024

VTech RM5754HD Handleiding

13 December 2024

VTech VM3252 Handleiding

16 November 2024

VTech RM5764HD Handleiding

16 November 2024

VTech DM1211 Handleiding

16 November 2024

Handleiding Babyfoon

Nieuwste handleidingen voor Babyfoon

British Telecom Baby Monitor 200 Handleiding

18 Februari 2025

British Telecom Digital Video Baby Monitor 1000 Handleiding

18 Februari 2025

British Telecom Digital Baby Monitor 350 Lightshow Handleiding

18 Februari 2025

Oricom SC340 Handleiding

11 Februari 2025

Denver CCT-2500 Handleiding

10 Februari 2025

Comtel CT-1311 Handleiding

25 Januari 2025

Comtel CT 1900 Handleiding

25 Januari 2025

Comtel CT-2400 Handleiding

25 Januari 2025

Lionelo Babyline 2.2 Handleiding

14 Januari 2025

Babysense HD S2 Handleiding

30 December 2025