System Sensor SPSCWL Handleiding

System Sensor Rookmelder SPSCWL

Lees hieronder de 📖 handleiding in het Nederlandse voor System Sensor SPSCWL (4 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

1 I56-0002-002

12/10/2018

For use with the following models:

Wall Speakers: SPSRL, SPSWL, SPSRL-P, SPSWL-P, SPSRL-SP, SPSWL-CLR-ALERT

Ceiling Speakers: SPSCRL, SPSCWL, SPSCWL-P, SPSCWL-SP, SPSCWL-CLR-ALERT

PRODUCT SPECIFICATIONS

Standard Operating Temperature: 32°F to 120°F (0°C to 49°C)

Humidity Range: 10 to 93% Non-condensing

Nominal Voltage (speakers): 25 Volts or 70.7 Volts

Maximum Supervisory Voltage: 50 VDC

Speaker Frequency Range: 400 – 4000 Hz

Power Settings: ¼, ½, 1, 2 Watts

Input terminal wire gauge: 12 to 18 AWG

Strobe Flash Rate: 1 flash per second

Nominal Voltage (strobes): Regulated 12VDC, regulated 24VDC or FWR

Operating Voltage Range (includes fire alarm

panels with built in sync): 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal)

Operating Voltage with MDL3 Sync Module: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal)

DIMENSIONS FOR PRODUCTS AND ACCESSORIES MOUNTING BOX OPTIONS

WALL PRODUCTS Length Width Depth SPEAKER STROBES

Wall Speaker Strobe 6.5" (165 mm) 5.00" (127 mm) 2.30" (58.4 mm) SBBSPRL/WL (wall), SBBCRL/WL (ceil-

ing), 4" x 4" x 2

"or deeper (When

using 12AWG, 14 AWG, or adding extra

wires in the box, a deeper box or exten-

sion ring is recommended.)

CEILING PRODUCTS Length Width Depth

Ceiling Speaker Strobe 6.8" (173 mm) N/A 2.87" (73mm)

WALL SURFACE MOUNT BACK BOX Length Width Depth

Speaker Strobe with SBBSPRL/WL Surface

Mount Back Box 6.62" (168mm) 5.12" (130 mm) 2.30" (58.4 mm)

CEILING SURFACE MOUNT BACK BOX Diameter Depth

Speaker Strobe with SBBCRL/WL Surface

Mount Back Box 6.92" (176 mm) 5.37" (116mm)

NOTICE: This manual shall be left with the owner/user of this equipment.

BEFORE INSTALLING

Please read the System Sensor Voice Evacuation Application Guide, which

provides detailed information on speaker notification devices, wiring and

special applications. Copies of this manual are available from System Sensor.

NFPA 72 and NEMA guidelines should be observed. System Sensor also rec-

ommends installing fire alarm speakers in compliance with NFPA 72, ANSI/

UL 1480 and NEC 760

Important: The notification appliance used must be tested and maintained

following NFPA 72 requirements.

GENERAL DESCRIPTION

System Sensor series of notification appliances offer a wide range of audible

and visible devices for life safety notification. Our indoor speaker strobes

come with 7 field selectable candela setting. The strobe portion is designed

to be used in 12 VDC, 24VDC, or 24V FWR (full wave rectified) systems. The

speaker is designed to be used at either 25 or 70.7 volts, and operate at any

one of four input power levels. Our speaker strobes are suitable for dry and

damp environments. These products are electrically backwards compatible

with previous generation of System Sensor speaker strobes. With its low total

harmonic distortion, the System Sensor SPL series offers high fidelity sound

output.

Speakers Strobes are public mode notification appliances intended to alert oc-

cupants of a life safety event. The speaker is listed to ANSI/UL 1480 (public

mode) and the strobe is listed to ANSI UL 1638 (public mode).

FIRE ALARM SYSTEM CONSIDERATIONS

System Sensor also recommends installing fire alarm speakers in compliance

with NFPA 72, ANSI/UL 1480 and NEC 760.

SYSTEM DESIGN

The system designer must make sure that the total current drawn by the de-

vices on the loop does not exceed the current capability of the panel supply,

and that the last device on the circuit is operated within its rated voltage. The

current draw information for making these calculations can be found in the

tables within this manual. For convenience and accuracy, use the voltage drop

calculator on the System Sensor website (www.systemsensor.com).

When calculating the voltage for the last device, it is necessary to consider

the voltage drop due to the resistance of the wire. The thicker the wire, the

smaller the voltage drop. Note that if Class A wiring is installed, the wire

length may be up to twice as long as it would be circuits that are not fault

tolerant. The total number of strobes on a single NAC must not exceed 69 for

24 volt applications.

AVAILABLE CANDELA SETTINGS

System Sensor offers a wide range of candela settings for your life safety

needs. In order to select your candela output, adjust the slide switch on the

rear of the product to the desired candela setting on the selector switch. (See

Figure 1.)

The candela setting can also be verified by looking into the small window

on the front of the unit. See Tables 1 and 2 for candela settings for wall and

ceiling products. All products meet the light output profiles specified in the

appropriate UL Standards. (See Figures 2–4.)

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Selectable Output Speaker Strobes

– Wall and Ceiling Mount

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

I56-0002-002

2 I56-0002-002

12/10/2018

FIGURE 4. LIGHT OUTPUT - VERTICAL DISPERSION, CEILING TO WALLS

TO FLOOR

Degrees* Percent of

Rating

0 100

5-25 90

30-45 75

50 55

60 45

65 35

70 35

75 30

80 30

85 25

90 25

A0468-00

WIRING AND MOUNTING

All wiring must be installed in compliance with the National Electric Code

and the local codes as well as the authority having jurisdiction. Wiring must

not be of such length or wire size which would cause the notification appli-

ance to operate outside of its published specifications. Improper connections

can prevent the system from alerting occupants in the event of an emergency.

Wire sizes up to 12 AWG (2.5 mm²) may be used with the mounting plate. The

mounting plate ships with the terminals set for 12 AWG wiring.

Make wire connections by stripping about

" of insulation from the end of

the wire. Then slide the bare end of the wire under the appropriate clamping

plate and tighten the clamping plate screw.

See Figure 5 for wiring terminals and strip guide reference.

1. Connect the speaker. (See Figure 5.)

2. There are two rotary switches on the back of the product. The first switch

is used to select either 25 or 70.7 volts input and the second switch is used to

select the input power of ¼, ½, 1 or 2 watts. (See Figure 6.)

FIGURE 5. WIRING DIAGRAM AND WIRING TERMINALS

(-)

(+)

(-)

(+)

(-)

(+)

(-)

(+)

From FACP

OUTPUT

To Next Device or EOL

From Amplifier

INPUT

To Next Device or EOL

A0519-01

Wiring Terminals

1. Negative (-). Line in and out

2. Positive (+). Line in and out

3. Positive (+). Line in and out

NOTE: Do not loop electrical wiring un-

der terminal screws. Wires connecting

the device to the control panel must be

broken at the device terminal connec-

tion in order to maintain electrical su-

pervision.

FIGURE 6. SPEAKER WATTAGE AND VOLTAGE SETTINGS

A0419-01

FIGURE 1. CANDELA SELECTOR

A0486-00

CURRENT DRAW AND AUDIBILITY RATINGS

For the strobe, the current draw for each setting is listed in Tables 1 and 2.

TABLE 1. WALL-MOUNT STROBE CURRENT DRAW (mA)

Candela

8-17.5

Volts 16-33 Volts

DC DC FWR

15 88 43 60

NOTE: Products set at 15 and 30

candela automatically work on ei-

ther 12V or 24V power supplies.

The products are not listed for

12V DC operation when set to any

other candela settings.

30 143 63 83

75 - 136107

95 - 155121

110 - 148 179

135 - 172 209

185 - 222 257

TABLE 2. CEILING-MOUNT STROBE CURRENT DRAW (mA)

Candela

8-17.5

Volts 16-33 Volts

DC DC FWR

15 87 6041

NOTE: Products set at 15 and 30

candela automatically work on

either 12V or 24V power supplies.

The products are not listed for 12V

DC operation when set to any other

candela settings.

30 153 63 86

75 - 142111

95 - 134 164

115 - 158 191

150 - 189 228

177 - 226 264

FIGURE 2. WALL LIGHT OUTPUT – FIGURE 3. VERTICAL

HORIZONTAL DISPERSION DISPERSION, WALL TO FLOOR

Degrees* Percent of

Rating Degrees* Percent of

Rating

0 0100 100

5-25 90 5-30 90

30-45 75 35 65

50 55 40 46

55 45 45 34

60 40 2750

65 35 55 22

70 35 60 18

75 65 1630

80 1530 70

85 25 75 13

90 25 80 12

Compound 45

to the left 24 85 12

Compound 45

to the right 24 90 12

A0467-00

A0469-00

*Tolerance of ±1 degree is permitted.

3 I56-0002-002

12/10/2018

SHORTING SPRING FEATURE

System Sensor notification appliances come with a shorting spring that is pro-

vided between terminals 2 and 3 of the mounting plate to enable system con-

tinuity checks after the system has been wired, but prior to installation of the

final product. (See Figure 7.) This spring will automatically disengage when

the product is installed, to enable supervision of the final system.

FIGURE 7. SHORTING SPRING

Shorting

Spring

WIRING TERMINALS

1. Negative (-). Line in and out

2. Positive (+). Line in and out

3. Positive (+). Line in and out

Strip Guide

A0499-02

AVAILABLE POWER SETTINGS

System Sensor offers a wide range of power settings for your life safety needs,

including ¼, ½, 1, and 2W.

Sound levels data per UL 1480 can be found in Table 3.

TABLE 3. SOUND LEVELS FOR EACH TRANSFORMER POWER SETTING

Setting UL Reverberant

(dBA @10 ft)

UL Anechoic

(dBA @10 ft)

¼ W 77 77

½ W 80 80

1 W 83 83

2 W 86 86

CAUTION

Signal levels exceeding 130% rated signal voltage can damage the speaker.

Consequently, an incorrect tap connection may cause speaker damage. This

means that if a 25V tap is selected when a 70.7V amplifier is being used,

speaker damage may result. Therefore, be sure to select the proper taps for the

amplifier voltage/input power level combination being used.

MOUNTING AND REMOVNG APPLIANCE

1. Attach mounting plate to junction box using two of the provided Philips

head screws. (See Figures 8 and 9.)

2. Connect field wiring according to terminal designations. (See Figure 5.)

3. If the product is not to be installed at this point, use the protective dust

cover to prevent contamination of the wiring terminals on the mounting

plate.

4. To attach product to mounting plate:

a. Remove the protective dust cover.

b. Hook the tabs on the top of the product housing into the grooves on mount-

ing plate.

c. Pivot the product into position to engage the terminals on the mounting

plate. Make sure that the tabs on the back of the product housing fully en-

gage with the mounting plate.

d. Hold product in place with one hand, and secure product by tightening the

single mounting screw in the front of the product housing.

Ceiling Models only: To remove product from the mounting plate, press the

locking button after loosening the captive mounting screw.

CAUTION

The “hold in place” snaps are not intended to secure the product to the back

box. The product must be secured to the back box using the screws provided.

CAUTION

Factory finish should not be altered: Do not paint!

CAUTION

Do not over tighten mounting plate screws; this may cause mounting plate

to flex.

FIGURE 8. WALL SPEAKER/STROBE

A0522-01

FIGURE 9. CEILING SPEAKER/STROBE

A0521-02

Locking

Button

A0575-00

TAMPER SCREW

For tamper resistance, the standard captive screw may be replaced with a Torx

screw (sold separately).

1. To remove the captive screw, back out the screw and apply pressure to the

back of the screw until it disengages from the housing. Replace with Torx

screw. (See Figure 10.)

FIGURE 10. TAMPER SCREW

T15 Torx

#6-32, 5/8"

SCREW-TMPR-50

A0502-01

INSTALLING A SURFACE MOUNT BACK BOX

1. The surface mount back box may be secured directly to the wall or

ceiling. Use of grounding bracket with ground screw is optional. (See

Figures 11 and 12.)

2. The wall mount box must be mounted with the up arrow pointing up. (See

Figure 13.)

NOTE: Ceiling Surface Mount Back Box SBBCR/CWL is a common back box

for ceiling horn strobes, strobes and ceiling speakers and speaker strobes. Use

Product specificaties

Merk:	System Sensor
Categorie:	Rookmelder
Model:	SPSCWL
Type stroombron:	DC
Koolmonoxidemelder:	Nee
Bedrijfstemperatuur centrale besturingseenheid (T-T):	0 - 49 °C
Brandmeldcentrale:	Ja
Centrale besturingseenheid werkzaam bij relatieve vochtigheid (V-V):	10 - 93 procent
Geluidsalarmeenheid voor noodgevallen:	Ja