System Sensor 2151 Handleiding

System Sensor Rookmelder 2151

Lees hieronder de 📖 handleiding in het Nederlandse voor System Sensor 2151 (2 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 69 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

2151/2151T Low Prole

Photoelectronic Plug-in

Smoke Detectors

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

BEFORE INSTALLING

Please thoroughly read System Sensor’s Applications Guide for System Smoke

Detectors (SPAG91), which provides detailed information on detector spacing,

placement, zoning, wiring, and special applications. This manual is available

online at www.systemsensor.com.

NOTICE: This manual should be left with the owner/user of this equipment.

IMPORTANT: The detector must be tested and maintained regularly following

NFPA 72 requirements. The detector should be cleaned at least once a year.

GENERAL DESCRIPTION

The 2151 low-profile photoelectronic detector uses a state-of-the-art optical

sensing chamber. This detector is designed to provide open area protection

and to be used with compatible UL listed control panels only. The capability

of plugging this detector into a variety of special bases makes it more versatile

than equivalent direct-wired models.

Two LEDs on each detector provide local 360° visible alarm indication. They

flash every five seconds indicating that power is applied and the detector

is working properly. The LEDs latch on in alarm. LEDs will be off when a

trouble condition exists indicating that the detector sensitivity is outside the

listed limit. Remote LED annunciator capability is standard and may be imple-

mented through an optional accessory RA400Z/RA100Z. The alarm can be

reset only by a momentary power interruption. This detector may be tested by

activating the internal reed switch with a magnet.

BASE SELECTION AND WIRING GUIDE

Refer to the installation instructions for the Plug-in Detector Bases for base se-

lection and wiring instructions. System Sensor has a variety of detector bases

available for this smoke detector, including 2-wire applications with and with-

out relays and/or current limiting resistors, 4-wire and 120VAC applications.

All bases are provided with screw terminals for power, ground, remote an-

nunciator connections and relay contact connections, if applicable. The elec-

trical ratings for each detector-base combination are also included in the base

installation instructions.

INSTALLATION

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations.

NOTE: Verify that all detector bases are installed, that the initiating-device

circuits have been tested, and that the wiring is correct. (Refer to detector base

manual for testing procedure.)

WARNING

Remove power from initiating-device circuits before installing detectors.

1. Install detectors:

a. Place the detector into the detector base.

b. Turn the detector clockwise until the detector drops into place.

c. Continue turning detector clockwise to lock it in place.

2. Tamper Resistance: The detector bases can be made tamper resistant.

SPECIFICATIONS

Size

Height: 2.0 inches (51 mm) installed in B401 Base

Diameter: 4.1 inches (104 mm) installed in B401 Base

6.1 inches (155 mm) installed in B110LP Base

Weight: 3.1 oz. (88 g)

Operating Temperature Range: 0°C to 49°C (32°F to 120°F); 2151,0°C to 38°C (32°F to 100°F); 2151T

Operating Humidity Range: 10% to 93% Relative Humidity noncondensing

Heat Sensor (2151T only): 135°F Fixed Temperature Electronic Thermistor

Operating Voltage: 8.5 to 35VDC

Standby Current: 120µA

Latching Alarm: Reset by momentary power interruption.

When capability is enabled, detectors cannot be removed from the base with-

out the use of a tool. See the detector base installation manual of the detector

base for details in using this capability.

3. After all detectors have been installed, apply power to the control unit.

4. Test the detector using the magnet as described under TESTING.

5. Reset the detector at the system control panel.

6. Notify the proper authorities that the system is back on line.

TESTING

Before testing, notify the proper authorities that the smoke detector system is

undergoing maintenance and will temporarily be out of service. Disable the

zone or system undergoing maintenance to prevent unwanted alarms. Detec-

tors must be tested after installation and as part of periodic maintenance. Test

2151 and 2151T as follows:

NOTE: Before testing the detector, check to ensure the LEDs blink. If they

do not, the detector has lost power (check the wiring), it is defective (return

it for repair), or the detector sensitivity is outside the listed limits.

A. Test Magnet (p/n M02-04-01 or M02-09-00)

1. Place the magnet against the cover in the location designated by the

raised mark to activate the test feature (see Figure 1).

2. The LEDs should latch ON within 5 seconds indicating alarm and an-

nunciating the panel.

B. Test Module (SENS-RDR)

Use the SENS-RDR Sensitivity Reader to measure the sensitivity of the detec-

tors. Please refer to the SENS-RDR instruction manual for operating details.

C. Smoke Entry

The GEMINI model 501 aerosol generator can be used for smoke entry

testing. Set the generator to represent 4%/ft to 5%/ft obscuration as de-

scribed in the GEMINI 501 manual. Using the bowl shaped applicator,

apply aerosol until the panel alarms.

Additionally, canned aerosol simulated smoke (canned smoke agent)

may be used for smoke entry testing of the smoke detector. Tested and

approved aerosol smoke products are:

MANUFACTURER MODEL

Home Safeguard Industries 25S

SDi CHEK02 and CHEK06

SDi SOLOA4

SDi SMOKESABRE-01

When used properly, the canned smoke agent will cause the smoke detector

to go into alarm. Refer to the manufacturer’s published instructions for proper

use of the canned smoke agent.

I56-2806-007R

1 I56-2806-007R

06-10

CAUTION

Canned aerosol simulated smoke (canned smoke agent) formulas will vary by

manufacturer. Misuse or overuse of these products may have long term ad-

verse effects on the smoke detector. Consult the canned smoke agent manufac-

turer’s published instructions for any further warnings or caution statements.

D. Direct Heat Method (Hair Dryer of 1000-1500 watts) 2151T only

A hair dryer of 1000-1500 watts should be used to test the thermistors. Di-

rect the heat toward either of the two thermistors, holding the heat source

approximately 12 inches from the detector in order to avoid damaging

the plastic housing. The detector will reset only after it has had sufficient

time to cool. Make sure both thermistors are tested individually.

Notify the proper authorities that the system is back on line.

Detectors that fail these tests should be cleaned as described under MAIN-

TENANCE and retested. If the detectors still fail these tests, they should be

returned for repair.

LED Status

Indicators

Magnet Test

Marker

Test Magnet

Position

Test Magnet

Position

Magnet Test

Marker

SENS-RDR

Location

FIGURE 1. BOTTOM AND SIDE VIEWS SHOWING POSITION OF

TEST MAGNET:

Sensor

Cover

Sensing

Chamber

Cover and

Screen

Cover

Removal

Tabs Sensing

Chamber

Optional

Thermistors

(2151T only)

FIGURE 2:

C0892-01

C0145-03

SPECIAL NOTE REGARDING SMOKE DETECTOR GUARDS

Smoke detectors are not to be used with detector guards unless the combina-

tion has been evaluated and found suitable for that purpose.

CAUTION

Dust covers are an effective way to limit the entry of dust into smoke detector sens-

ing chambers. However, they may not completely prevent airborne dust particles

from entering the detector. Therefore, System Sensor recommends the removal

of detectors before beginning construction or other dust producing activity.

Be sure to remove the dust covers from any sensors that were left in place dur-

ing construction as part of returning the system to service.

CAUTION

Smoke detectors are not to be used with detector guards unless the combina-

tion has been evaluated and found suitable for that purpose.

System Sensor warrants its enclosed smoke detector to be free from defects in materials

and workmanship under normal use and service for a period of three years from date

of manufacture. System Sensor makes no other express warranty for this smoke detec-

tor. No agent, representative, dealer, or employee of the Company has the authority to

increase or alter the obligations or limitations of this Warranty. The Company’s obligation

of this Warranty shall be limited to the repair or replacement of any part of the smoke

detector which is found to be defective in materials or workmanship under normal use

and service during the three year period commencing with the date of manufacture.

After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return

Authorization number, send defective units postage prepaid to: Honeywell, 12220 Rojas

THREE-YEAR LIMITED WARRANTY

Drive, Suite 700, El Paso TX 79936, USA. Please include a note describing the malfunc-

tion and suspected cause of failure. The Company shall not be obligated to repair or

replace units which are found to be defective because of damage, unreasonable use,

modifications, or alterations occurring after the date of manufacture. In no case shall the

Company be liable for any consequential or incidental damages for breach of this or any

other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by

the Company’s negligence or fault. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This Warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

CLEANING

Before removing the detector, notify the proper authorities that the smoke

detector system is undergoing maintenance and will be temporarily out of

service. Disable the zone or system undergoing maintenance to prevent un-

wanted alarms.

1. Remove the sensor to be cleaned from the system.

2. Remove the sensor cover by pressing firmly on each of the four removal

tabs that hold the cover in place.

3. Vacuum the screen carefully without removing it.

If further cleaning is required continue with Step 4, otherwise skip to

Step 7.

4. Remove the chamber cover/screen assembly by pulling it straight out.

5. Use a vacuum cleaner or compressed air to remove dust and debris from

the sensing chamber.

6. Reinstall the chamber cover/screen assembly by sliding the edge over the

sensing chamber. Turn until it is firmly in place.

7. Replace the cover using the LEDs to align the cover and then gently

pushing it until it locks into place. Make sure that the thermistors do not

become bent under the cover on 2151T.

8. Reinstall the detector.

9. Test the detector as described in TESTING.

10. Reconnect disabled circuits.

11. Notify the proper authorities that the system is back on line.

2 I56-2806-007R

Product specificaties

Merk:	System Sensor
Categorie:	Rookmelder
Model:	2151
Kleur van het product:	Wit
Gewicht:	104 g
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Diameter:	155 mm
Beste gebruik:	Home, Office
Detector type:	Foto-electrische reflectie detector
Koppelbaar:	Ja
Geschikt voor gebruik binnen:	Ja
Bedrijfstemperatuur (T-T):	0 - 49 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 93 procent