First Alert SM210 Handleiding

First Alert Rookmelder SM210

Lees hieronder de 📖 handleiding in het Nederlandse voor First Alert SM210 (2 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

USER’S MANUAL

SMOKE ALARM

10-YEAR SEALED BATTERY

Model SM210

IMPORTANT! PLEASE READ CAREFULLY AND SAVE.

The warnings/limitations card and manual contains important information

about your Smoke Alarm’s operation. If you are installing this Alarm for use

by others, you must leave this manual—or a copy of it—with the end user.

Para el manual del usuario en español, por favor visite rstalert.com

01 INTRODUCTION

Thank you for choosing First Alert

for your Smoke Alarm needs. You have purchased a state-of-the-art Smoke Alarm

designed to provide you with early warning of a re. Please take the time to read this manual and make the Smoke Alarm

an integral part of your family’s safety plan.

BASIC SAFETY INFORMATION

! WARNING!

• This unit will not alert hearing impaired residents. It is recommended that you install special units which use devices

like ashing strobe lights to alert hearing impaired residents.

• Do not connect this unit to any other Alarm or auxiliary device. It is a single-station unit that cannot be linked to other

devices. Connecting anything else to this unit may prevent it from working properly.

• Unit will not operate without battery power. The Smoke Alarm cannot work until you activate the battery power pack.

! CAUTION!

• Do not install this unit over an electrical junction box. Air currents around junction boxes can prevent smoke from

reaching the sensing chamber and prevent the unit from Alarming. Only AC powered units are intended for installation

over junction boxes.

• Do not stand too close to the unit when the Alarm is sounding. It is loud to wake you in an emergency. Exposure to the

horn at close range may harm your hearing.

• Do not paint over the unit. Paint may clog the openings to the sensing chamber and prevent the unit from

operating properly.

02 ABOUT SMOKE ALARMS

TYPES OF ALARMS

All these Smoke Alarms are designed to provide early warning of res if located, installed and cared for as described in

the user’s manual, and if smoke reaches the Alarm. If you are unsure which type of unit to install, refer to NFPA (National

Fire Protection Association) 72 (National Fire Alarm and Signaling Code) and NFPA 101 (Life Safety Code). National Fire

Protection Association, One Batterymarch Park, Quincy, MA 02269-9101. Local building codes may also require specic

units in new construction or in different areas of the home.

Battery (DC) operated Smoke Alarms: Provide protection even when electricity fails, provided the batteries are fresh

and correctly installed. Units are easy to install, and do not require professional installation. They do not, however, provide

interconnected functionality.

AC powered Smoke Alarms: Can be interconnected so if one unit senses smoke, all units Alarm. They do not operate if

electricity fails.

AC with battery (DC) back-up: will operate if electricity fails, provided the batteries are fresh and correctly installed. AC

and AC/DC units must be installed by a qualied electrician.

Smoke Alarms for Solar or wind energy users and battery backup power systems: AC powered Smoke Alarms

should only be operated with true or pure sine wave inverters. Operating this Smoke Alarm with most battery powered

UPS (uninterruptible power supply) products or square wave or “quasi sine wave” inverters . If will damage the Alarm

you are not sure about your inverter or UPS type, please consult with the manufacturer to verify.

Smoke Alarms for the hearing impaired: Special purpose Smoke Alarms should be installed for the hearing impaired.

They include a visual Alarm and an audible Alarm horn, and meet the requirements of the Americans with Disabilities Act.

These units can be interconnected so if one unit senses smoke, all units Alarm.

Smoke Alarms are not to be used with detector guards unless the combination has been evaluated and found suitable

for that purpose.

All First Alert

Smoke Alarms conform to regulatory requirements, including UL217 and are designed to detect

particles of combustion. Smoke particles of varying number and size are produced in all res.

Ionization technology is generally more sensitive than photoelectric technology at detecting small particles, which

tend to be produced in greater amounts by aming res, which consume combustible materials rapidly and

spread quickly. Sources of these res may include paper burning in a wastebasket, or a grease re in the kitchen.

Photoelectric technology is generally more sensitive than ionization technology at detecting large particles,

which tend to be produced in greater amounts by smoldering res, which may smolder for hours before

bursting into ame. Sources of these res may include cigarettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each level and in every bedroom of your home.

03 INSTALLATION

BEFORE YOU INSTALL THIS SMOKE ALARM

Important! Read “Recommended Locations for Smoke Alarms” and “Locations to Avoid for Smoke Alarms” before

beginning. This unit monitors the air, and when smoke reaches its sensing chamber, it Alarms. It can give you more time

to escape before re spreads. This unit can ONLY give an early warning of developing res if it is installed, maintained

and located where smoke can reach it, and where all residents can hear it, as described in this manual. This unit will not

sense gas, heat, or ame. It cannot prevent or extinguish res.

Understand The Different Type of Smoke Alarms: Battery powered or electrical? Different Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms: Fire Safety Professionals recommend at least one Smoke Alarm on every

level of your home, in every bedroom, and in every bedroom hallway or separate sleeping area. See “Recommended

Locations for Smoke Alarms” and “Locations to Avoid for Smoke Alarms” for details.

Know What Smoke Alarms Can and Can’t Do: A Smoke Alarm can help alert you to re, giving you precious time to

escape. It can only sound an Alarm once smoke reaches the sensor. See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes: This Smoke Alarm is designed to be used in a typical single family home. It alone

will not meet requirements for boarding houses, apartment buildings, hotels or motels. See “Special Compliance

Considerations” for details.

WHERE TO INSTALL THIS ALARM

• On every level of your home, including nished attics and basements.

• Inside every bedroom, especially if people sleep with doors closed.

• In the hall near every sleeping area. If your home has multiple sleeping areas, install a unit in each. If a hall is over 40

feet (12 meters) long, install an Alarm at each end.

• At the top of the rst-to-second level stairway, and at bottom of basement stairway.

RECOMMENDED PLACEMENT:

Smoke Alarm

One on every level and

in every bedroom

Carbon Monoxide Alarm

One on every level and

in every bedroom

Fire Extinguisher

One on every level, plus

kitchen and garage

WHERE NOT TO INSTALL THIS ALARM

FOR BEST PERFORMANCE, IT IS RECOMMENDED YOU AVOID INSTALLING SMOKE ALARMS IN THESE AREAS:

• Where combustion particles are produced. Combustion particles form when something burns. Areas to avoid include

poorly ventilated kitchens, garages, and furnace rooms. Keep units at least 20 feet (6 meters) from the sources of

combustion particles (stove, furnace, water heater, space heater) if possible. In areas where a 20-foot (6-meter)

distance is not possible – in modular, mobile, or smaller homes, for example – it is recommended the Smoke

Alarm be placed as far from these fuel-burning sources as possible. The placement recommendations are intended

to keep these Alarms at a reasonable distance from a fuel-burning source, and thus reduce “unwanted” Alarms.

Unwanted Alarms can occur if a Smoke Alarm is placed directly next to a fuel-burning source. Ventilate these areas

as much as possible.

• In air streams near kitchens. Air currents can draw cooking smoke into the sensing chamber of a Smoke Alarm

near the kitchen.

• In very damp, humid or steamy areas, or directly near bathrooms with showers. Keep units at least 10 feet (3 meters)

away from showers, saunas, dishwashers, etc.

• Where the temperatures are regularly below 40˚ F (4.4˚ C) or above 100˚ F (37.8˚ C), including unheated buildings,

outdoor rooms, porches, or unnished attics or basements.

• In very dusty, dirty, or greasy areas. Do not install a Smoke Alarm directly over the stove or range. Keep laundry room

Smoke Alarms free of dust or lint.

• Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can blow smoke away from the unit, preventing it

from reaching the sensing chamber.

• In insect infested areas. Insects can clog openings to the sensing chamber and cause unwanted Alarms.

• Less than 12 inches (305mm) away from uorescent lights. Electrical “noise” can interfere with the sensor.

• In “dead air” spaces. “Dead air” spaces may prevent smoke from reaching the Smoke Alarm.

AVOIDING DEAD AIR SPACES

“Dead air” spaces may prevent smoke from reaching the Smoke Alarm. To avoid dead air spaces, follow the installation

recommendations below.

On ceilings, install Smoke Alarms as close to the center of the ceiling as possible. If this is not possible, install the Smoke

Alarm at least 4 inches (102 mm) from the wall or corner.

For wall mounting (if allowed by building codes), the top edge of Smoke Alarms should be placed between 4 inches (102

mm) and 12 inches (305 mm) from the wall/ceiling line, below typical “dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the rst Smoke Alarm within 3 feet (0.9 meters) of the peak of the

ceiling, measured horizontally. Additional Smoke Alarms may be required depending on the length, angle, etc. of the

ceiling’s slope. Refer to NFPA 72 for details on requirements for sloped or peaked ceilings.

HOW TO INSTALL THIS ALARM

This unit is designed to be mounted on the ceiling, or on the wall if necessary.

Tools you will need: pencil, drill with 3/16" (5 mm) drill bit, standard athead screwdriver, hammer.

THE PARTS OF THIS SMOKE ALARM

1 Test/Silence button

2 Dual power indicator light and Alarm

indicator: Green LED provides visual

indication of an Alarm memory condition;

Red LED provides visual indication of an

Alarm and hush modes

3 Turn this way to remove

4 Turn this way to attach

5 Mounting bracket

6 Mounting slots

FOLLOW THESE SIMPLE STEPS

1. Choose a location. See “Where to Install This Alarm” for reference.

WARNING! Do not install this Alarm over an existing electrical box. Only AC powered units are intended for

installation over electrical boxes.

2. Mark hole locations 4-1/4" apart. Use the mounting bracket to verify the hole

mark locations are accurately spaced. If mounting on the wall, holes must be

aligned horizontally to ensure Alarm is mounted upright. Put the Alarm where it

won’t get covered with dust while you drill the holes.

3. Use a 3/16" (5mm) drill bit to drill through the marks you made for the

mounting holes.

4. Insert the plastic screw anchors (in the plastic bag with the screws) into the

holes. Tap the screw anchors gently with a hammer, if necessary, until they are

ush with the ceiling or wall.

5. Insert the screws but do not tighten completely. Leave them about 1/4" (6mm)

away from the wall. Attach the mounting bracket to the wall or ceiling by aligning

the round part of the slots with the screws. To mount on a wall, align the hole

marked A with the left screw. Rotate the bracket until the screws are completely

inside the raised portion of the circular recesses (see image). Once the screws

are completely inside the raised portion of the circular recesses, tighten the

screws until they are snug to secure the bracket. Do not over-tighten the screws.

Mounting Hole Sets

6. Activating the battery. Mount Alarm to mounting bracket to activate. Alarm

will be oriented as shown. Once unit is activated, it cannot be turned off.

Make sure the Alarm is locked into the mounting bracket.

NOTE: After you activate the battery, there may be Power and LED

activation indicators.

7. Test the Alarm. See “Weekly Testing.”

Action What You Will See & Hear

Under Normal Operations Horn: Power LED: Silent; Flashes green once a minute

When You Test the Alarm Horn: A short “chirp” and then 3 beeps, pause, 3 beeps

If Battery Becomes Low Horn: Power LED: 5 chirps every minute; One green ash

approximately once a minute

If Alarm is Not Operating Properly Horn: Power LED: 3 chirps every minute; Three green ashes

approximately once a minute

Alarm has reached End of Life Horn: Power LED: 5 chirps every minute; Five green ashes

approximately once a minute

Smoke is Detected Horn: 3 beeps, pause, 3 beeps; Flashes redPower LED:

Smoke Alarm is Silenced Horn: Power LED: Off; Flashes red

04 ALARM FEATURES

• Or low battery chirps for the life of the Alarm.No Battery Replacements:

• Add protection in minutes.Easy Installation:

• Let’s you know when it’s time to replace.End-of-Life Warning:

OPTIONAL LOCKING FEATURE

The optional locking feature is designed to prevent unauthorized removal of the Alarm. It is not necessary to

activate the lock in single-family households where unauthorized Alarm removal is not a concern.

Tools you will need: Needle-nose pliers or utility knife, standard

athead screwdriver

The feature uses a locking pin which is molded into the mounting

bracket. Remove locking pin by using needle-nose pliers or

a utility knife.

IMPORTANT!

To permanently remove the locking pin, insert a athead

screwdriver between the locking pin and the lock and pry the pin

out of the lock.

TO LOCK THE MOUNTING BRACKET

1. Using needle-nose pliers, detach the

pin from the mounting bracket.

2. Insert the locking pin through the hole

on the back of the Smoke Alarm as

shown in the diagram.

3. When you attach the Alarm to

the mounting bracket the locking

pin’s head will t into a notch

on the bracket.

TO UNLOCK THE MOUNTING BRACKET

1. Insert a athead screwdriver in between the

mounting bracket and the locking pin.

2. Pry the Alarm away from the bracket

by pushing up the screwdriver and

turning the Alarm counterclockwise (left)

at the same time.

HOW TO PERMANENTLY DEACTIVATE THE SMOKE ALARM

After Malfunction, 10 years of Operation Low Battery or End of Life Warnings,

deactivate the Alarm: Insert a tool below edge where shown and break tab.

Then slide activation switch to deactivate mode.

NOTE: At end of life (chirp): unit must be put into deactivation mode to

deactivate remaining stored energy in battery. Unit will no longer function

once put into this mode. Unit will resist re-mounting.

05 TESTING & MAINTENANCE

WEEKLY TESTING

! WARNING!

• use an open ame of any kind to test this unit. You might accidentally damage or set re to the unit NEVER

or to your home.

• If the Alarm ever fails to test properly, replace it immediately. Products under warranty may be returned to the

manufacturer for replacement. See “Limited Warranty” for details.

• stand close to the Alarm when the horn is sounding. Exposure at close range may be harmful to your hearing. DO NOT

When testing, step away when horn starts sounding.

! CAUTION!

It is important to test this unit every week to make sure it is working properly. Using the Test/Silence button is the

recommended way to test this Smoke Alarm. Press and hold the Test/Silence button on the cover of the unit until the

Alarm sounds (the unit may continue to Alarm for a few seconds after you release the button). If it does not Alarm, make

sure the unit is receiving power and test it again. If it still does not Alarm, replace it immediately. During testing you will

hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. Red LED ashes rapidly.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but there are a few simple things you must do to

keep it working properly.

• Test it at least once a week.

• Clean the Smoke Alarm at least once a month; gently vacuum off any dust using your household vacuum’s soft

brush attachment, and test the Smoke Alarm after cleaning. Never use water, cleaners or solvents since they may

damage the unit.

• If the Smoke Alarm becomes contaminated by excessive dirt, dust and/or grime, and cannot be cleaned to avoid

unwanted Alarms, replace the unit immediately.

• If the green power LED ashes 2 times every minute (horn is silent) it means that the Alarm needs to be cleaned as

indicated above. If green light continues to ash, replace Alarm.

• Relocate the unit if it sounds frequent unwanted Alarms. See “Locations to Avoid for Smoke Alarms” for details.

• Protect or cover the alarm when doing any maintenance to home i.e. sanding oors, painting, drywall patching, etc.

to prevent contamination.

IMPORTANT!

Actual service life depends on the Smoke Alarm and the environment in which it is installed. You replace the MUST

Smoke Alarm immediately once the unit starts “chirping” (the End of Life or Malfunction warning).

TROUBLESHOOTING GUIDE

IF THE ALARM... PROBLEM... YOU SHOULD...

Horn sounds 3 “chirps”

every minute.

MALFUNCTION SIGNAL.

Device is not working properly, and

needs to be replaced.

If unit is under warranty, contact

Consumer Support to process a

warranty replacement.

Horn sounds 5 chirps every

minute; has one Green ash LED

approx every minute.

Low Battery Signal, Alarm needs

to be replaced. Immediately replace the Alarm.

The ashes GREEN light

and the sounds 5 horn

“chirps” every minute.

END OF LIFE SIGNAL.

Alarm needs to be replaced. Immediately replace the Alarm.

Smoke Alarm sounds when no

smoke is visible.

Unwanted Alarm may be caused

by nonemergency source

like cooking smoke.

Silence Alarm using Test/Silence

button; clean the Alarm’s cover

with a soft, clean cloth. If frequent

unwanted Alarms continue, relocate

your Alarm. Alarm may be too close

to a kitchen, cooking appliance, or

steamy bathroom.

Power LED ashes Green 2

times every minute. Alarm requires cleaning.

Clean Alarm then press and

release the test button. See

Regular Maintenance section. If

Green LED Continues to ash,

contact Consumer Support.

If you have questions that cannot be answered by reading this manual, call the

Consumer Support Team at 1-800-323-9005

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking materials properly. Never smoke in bed. 2) Keep

matches or lighters away from children; 3) Store ammable materials in proper containers; 4) Keep electrical appliances

in good condition and don’t overload electrical circuits; 5) Keep stoves, barbecue grills, replaces and chimneys grease-

and debris-free; 6) Never leave anything cooking on the stove unattended; 7) Keep portable heaters and open ames,

like candles, away from ammable materials; 8) Don’t let rubbish accumulate. Keep Alarms clean, and test them weekly.

Replace Alarms immediately if they are not working properly. Smoke Alarms that do not work cannot alert you to a re. Keep

at least one working re extinguisher on every level, and an additional one in the kitchen. Have re escape ladders or other

reliable means of escape from an upper level in case stairs are blocked; 9) Have an escape plan and practice it regularly.

06 IF THIS SMOKE ALARM SOUNDS

RESPONDING TO AN ALARM

During an Alarm, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. The Red LED ashes rapidly.

! WARNING!

• If the unit Alarms get everyone out of the house immediately.

• If the unit Alarms and you are not testing the unit, it is warning you of a potentially dangerous situation that requires

your immediate attention. ignore any Alarm. Ignoring the Alarm may result in injury or death.NEVER

• Never remove the batteries from a battery operated Smoke Alarm to stop an unwanted Alarm (caused by cooking

smoke, etc.). Removing batteries disables the Alarm so it cannot sense smoke, and removes your protection. Instead

open a window or fan the smoke away from the unit. The Alarm will reset automatically.

WHAT TO DO IN CASE OF FIRE

• Don’t panic; stay calm. Follow your family escape plan.

• Get out of the house as quickly as possible. Don’t stop to get dressed or collect anything.

• Feel doors with the back of your hand before opening them. If a door is cool, open it slowly. Don’t open a hot door.

Keep doors and windows closed, unless you must escape through them.

• Cover your nose and mouth with a cloth (preferably damp). Take short, shallow breaths.

• Meet at your planned meeting place outside your home, and do a head count to make sure everybody got out safely.

• Call the Fire Department as soon as possible from outside. Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

! WARNING!

Alarms have various limitations. See “General Limitations of Smoke Alarms” for details.

07 USING THE SILENCE FEATURES

The Silence Feature can temporarily quiet an unwanted Alarm for up to 9 minutes. To use this feature, press the Test/

Silence button on the cover. If the unit will not silence and no heavy smoke is present, or if it stays in silence mode

continuously, it should be replaced immediately. The LED will ash every 10 seconds while in silence.

! WARNING!

The Silence Feature does not disable the unit—it makes it temporarily less sensitive to smoke. For your safety, if

smoke around the unit is dense enough to suggest a potentially dangerous situation, the unit will stay in Alarm

or may re-Alarm quickly. If you do not know the source of the smoke, do not assume it is an unwanted Alarm. Not

responding to an Alarm can result in property loss, injury, or death.

SILENCING THE LOW BATTERY WARNING

This Silence Feature can temporarily quiet the Low Battery Warning “chirp”. Press the Test/Silence button on the Alarm.

The Red light ashes normally, once every 6 minutes, during Low Battery Warning silence. After time, the low battery

“chirp” will resume. Deactivate the Smoke Alarm and replace it immediately.

IF YOU SUSPECT A PROBLEM

Smoke Alarms may not operate properly because of a dead or weak battery, a build-up of dirt, dust or grease on

the Smoke Alarm cover, or installation in an improper location. Clean the Smoke Alarm as described in “Regular

Maintenance,” and then test the Smoke Alarm again. If it fails to test properly when you use the test button, or if the

problem persists, replace the Smoke Alarm immediately.

• If you hear 3 or 5 chirps every minute or so, replace the Smoke Alarm.

• If you experience frequent non-emergency Alarms (like those caused by cooking smoke), try relocating

the Smoke Alarm.

• If the Alarm sounds when no smoke is visible, try cleaning or relocating the Smoke Alarm. The cover may be dirty.

• If the Alarm does not sound during testing, make sure the power pack activating lever is pushed all the way securely.

Do not try xing the Alarm yourself — this will void your warranty!

If the Smoke Alarm is still not operating properly, and it is still under warranty, please see “How to Obtain Warranty

Service” in the Limited Warranty.

08 REGULATORY INFORMATION FOR SMOKE ALARMS

RECOMMENDED LOCATIONS FOR SMOKE ALARMS

INSTALLING SMOKE ALARMS IN SINGLE-FAMILY RESIDENCES

The National Fire Protection Association (NFPA), recommends one Smoke Alarm on every level, in every sleeping area,

and in every bedroom. In new construction, the Smoke Alarms must be AC powered and interconnected. See “Agency

Placement Recommendations” for details. For additional coverage, it is recommended that you install a Smoke Alarm in

all rooms, halls, storage areas, nished attics, and basements, where temperatures normally remain between 40˚ F (4.4˚

C) and 100˚ F (37.8˚ C). Make sure no door or other obstruction could keep smoke from reaching the Smoke Alarms.

MORE SPECIFICALLY, INSTALL SMOKE ALARMS:

• On every level of your home, including nished attics and basements.

• Inside every bedroom, especially if people sleep with doors closed.

• In the hall near every sleeping area. If your home has multiple sleeping areas, install a unit in each.

• If a hall is over 40 feet (12 meters) long, install an Alarm at each end.

• At the top of the rst-to-second level stairway, and at bottom of basement stairway.

IMPORTANT!

Specic requirements for Smoke Alarm installation vary from state to state and from region to region. Check with your

local Fire Department for current requirements in your area. It is recommended AC or AC/DC units be interconnected

for added protection.

09 AGENCY PLACEMENT RECOMMENDATIONS

NFPA 72 CHAPTER 29 “FOR YOUR INFORMATION, THE NATIONAL FIRE ALARM AND SIGNALING CODE, NFPA 72,

READS AS FOLLOWS:”

29.5.1* Required Detection.

29.5.1.1* Where required by other governing laws, codes, or standards for a specic type of occupancy, approved single

and multiple-station Smoke Alarms shall be installed as follows:

1. *In all sleeping rooms and guest rooms

2. *Outside of each separate dwelling unit sleeping area, within 21 ft (6.4 m) of any door to a sleeping room, with the

distance measured along a path of travel

3. On every level of a dwelling unit, including basements

4. On every level of a residential board and care occupancy (small facility), including basements and excluding crawl

spaces and unnished attics

5. *In the living area(s) of a guest suite

6. In the living area(s) of a residential board and care occupancy (small facility)

(Reprinted with permission from NFPA 72

Protection Association, Quincy, MA 02269. This reprinted material is not the complete and ofcial position of the National

Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety).

(National Fire Alarm and Signaling Code

and NFPA 72

are registered trademarks of the National Fire Protection

Association, Inc., Quincy, MA 02269).

CALIFORNIA STATE FIRE MARSHAL (CSFM)

Early warning detection is best achieved by the installation of re detection equipment in all rooms and areas of the

household as follows: A Smoke Alarm installed in each separate sleeping area (in the vicinity, but outside bedrooms), and

Heat or Smoke Alarms in the living rooms, dining rooms, bedrooms, kitchens, hallways, nished attics, furnace rooms,

closets, utility and storage rooms, basements, and attached garages.

10 SPECIAL COMPLIANCE CONSIDERATIONS

This Smoke Alarm is suitable for use in apartments, condominiums, townhouses, hospitals, day care facilities, health care

facilities, boarding houses, group homes and dormitories provided a primary re detection system already exists to meet

re detection requirements in common areas like lobbies, hallways, or porches. Using this Smoke Alarm in common areas

may not provide sufcient warning to all residents or meet local re protection ordinances/regulations.

This Smoke Alarm alone is not a suitable substitute for complete re detection systems in places housing many

people—like apartment buildings, condominiums, hotels, motels, dormitories, hospitals, health care facilities, nursing

homes, day care facilities, or group homes of any kind. It is not a suitable substitute for complete re detection systems

in warehouses, industrial facilities, commercial buildings, and special-purpose non-residential buildings which require

special re detection and Alarm systems. Depending on the building codes in your area, this Smoke Alarm may be used to

provide additional protection in these facilities.

In new construction, most building codes require the use of AC or AC/DC powered Smoke Alarms only. In existing

construction, AC, AC/DC, or DC powered Smoke Alarms can be used as specied by local building codes. THIS

EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION’S STANDARD

72 (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Refer to NFPA 101 (Life Safety Code),

local building codes, or consult your Fire Department for detailed re protection requirements in buildings not dened

as “households”.

GENERAL LIMITATIONS OF SMOKE ALARMS

Smoke Alarms have played a key role in reducing deaths resulting from home res worldwide. However, like any warning

device, Smoke Alarms can only work if they are properly located, installed, and maintained, and if smoke reaches them.

They are not foolproof.

Smoke Alarms may not waken all individuals. Practice the escape plan at least twice a year, making sure that

everyone is involved – from kids to grandparents. Allow children to master re escape planning and practice before

holding a re drill at night when they are sleeping. If children or others do not readily waken to the sound of the Smoke

Alarm, or if there are infants or family members with mobility limitations, make sure that someone is assigned to assist

them in re drill and in the event of an emergency. It is recommended that you hold a re drill while family members are

sleeping in order to determine their response to the sound of the Smoke Alarm while sleeping and to determine whether

they may need assistance in the event of an emergency.

Smoke Alarms cannot work without power. Battery operated units cannot work if the batteries are missing,

disconnected or dead, if the wrong type of batteries are used, or if the batteries are not installed correctly. AC units cannot

work if the AC power is cut off for any reason (open fuse or circuit breaker, failure along a power line or at a power

station, electrical re that burns the electrical wires, etc.). If you are concerned about the limitations of battery or AC

power, install both types of units.

Smoke Alarms cannot detect res if the smoke does not reach the Alarms. Smoke from res in chimneys or walls,

on roofs, or on the other side of closed doors may not reach the sensing chamber and set off the Alarm. That is why one

unit should be installed inside each bedroom or sleeping area—especially if bedroom or sleeping area doors are closed

at night—and in the hallway between them.

Smoke Alarms may not detect re on another level or area of the home. For example, a stand-alone unit on the

second level may not detect smoke from a basement re until the re spreads. This may not give you enough time to

escape safely. That is why recommended minimum protection is at least one unit in every sleeping area, and every

bedroom on every level of your home. Even with a unit on every level, stand-alone units may not provide as much

protection as interconnected units, especially if the re starts in a remote area. Some safety experts recommend installing

interconnected AC powered units with battery back-up (see “About Smoke Alarms”) or professional re detection

systems, so if one unit senses smoke, all units Alarm. Interconnected units may provide earlier warning than stand-alone

units since all units Alarm when one detects smoke.

Smoke Alarms may not be heard. Though the Alarm horn in this unit meets or exceeds current standards, it may not be

heard if: 1) the unit is located outside a closed or partially closed door, 2) residents recently consumed alcohol or drugs,

3) the Alarm is drowned out by noise from stereo, TV, trafc, air conditioner or other appliances, 4) residents are hearing

impaired or sound sleepers. Special purpose units, like those with visual and audible Alarms, should be installed for

hearing impaired residents.

The Alarm may not have time to Alarm before the re itself causes damage, injury, or death, since smoke from

some res may not reach the unit immediately. Examples of this include persons smoking in bed, children

playing with matches, when a person’s clothing catches re while cooking, res caused by violent explosions

resulting from escaping gas, or incendiary res where the re grows so rapidly that an occupant’s egress is

blocked even with properly located Smoke Alarms.

Smoke Alarms are not foolproof. Like any electronic device, Smoke Alarms are made of components that can wear out

or fail at any time. You must test the unit weekly to ensure your continued protection. Smoke Alarms cannot prevent or

extinguish res. They are not a substitute for property or life insurance.

Smoke Alarms have a limited life. The unit should be replaced immediately if it is not operating properly. You should

always replace a Smoke Alarm after 10 years from date of purchase. Write the purchase date on the space provided

on back of unit.

12 LIMITED WARRANTY

First Alert

warrants that for a period of ten years from the date of purchase, this product will be free from defects in

material and workmanship. First Alert, at its option, will repair or replace this product or any component of the product

found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or

component. If the product is no longer available, replacement may be made with a similar product of equal or greater

value. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.

Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. First Alert dealers, service

centers, or retail stores selling First Alert products do not have the right to alter, modify or any way change the terms and

conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or

misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair

or alteration by anyone other than First Alert or an authorized service center. Further, the warranty does not cover Acts of

God, such as re, ood, hurricanes and tornadoes.

First Alert shall not be liable for any incidental or consequential damages caused by the breach of any express or implied

warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or tness for a

particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions

do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied

warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specic legal rights,

and you may also have other rights that vary from state to state or province to province.

HOW TO OBTAIN WARRANTY SERVICE

Service: If service is required, do not return the product to your retailer. In order to obtain warranty service, contact the

Consumer Support Team at 1-800-323-9005. To assist us in serving you, please have the model number and date of

purchase available when calling.

Disposal: Please follow local guidelines regarding the disposal or recycling of batteries and/or electronics.

The Alarm should be deactivated before disposal. See, “To Permanently Deactivate the Smoke Alarm”.

For your records, please record:

Date Purchased: ___________________________

Where Purchased: __________________________

Date Installed: __________/__________Month/Year

Replace Alarm 10 years after installation.

Please write the date in the space provided:

_____________/____________Month/Year

The Alarm will also provide

an audible End-of-Life Signal

approximately 10 years after

installation to remind you to

replace the unit.

The End-of-Life Signal can be

silenced for up to 2 days. Do not

unplug or deactivate the Alarm

until you get replacement.

Printed in Mexico | M08-0596-000 03/23

CONFORMS TO UL STD 217

rstalert.com

products are manufactured by Resideo Technologies, Inc.

and its afliates. 3901 Liberty Street, Aurora, IL 60504-8122.

Consumer Support Team: (800) 323-9005 | rstalert.com

Product specificaties

Merk:	First Alert
Categorie:	Rookmelder
Model:	SM210

Heb je hulp nodig?

Als je hulp nodig hebt met First Alert SM210 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Rookmelder First Alert

First Alert SM210 Handleiding

23 December 2024

First Alert SMI100-AC Handleiding

23 December 2024

First Alert SMI105-AC Handleiding

23 December 2024

First Alert SMI100 Handleiding

23 December 2024

First Alert SMCO210 Handleiding

24 Juni 2024

First Alert SMCO210V Handleiding

24 Juni 2024

First Alert SMCO100V-AC Handleiding

24 Juni 2024

First Alert SMICO100-AC Handleiding

24 Juni 2024

First Alert SA320 Handleiding

9 April 2024

First Alert P910 Handleiding

31 Augustus 2023

Handleiding Rookmelder

Nieuwste handleidingen voor Rookmelder

Kidde CO120X Handleiding

2 December 2024

EQ-3 HM-Sec-SD-2 Handleiding

30 November 2024

EQ-3 HM-Sec-SD Handleiding

30 November 2024

EQ-3 HMIP-SWSD Handleiding

30 November 2024

Pentatech RA170Q Handleiding

24 November 2024

Cordes CC-4100 Handleiding

18 November 2024

Cordes CC-3000 Handleiding

18 November 2024

Cordes CC-500 Handleiding

18 November 2024

Nexa KD-134A Handleiding

18 November 2024

Gloria R-5 Handleiding

16 November 2024