Shelly 2.5 Handleiding

Shelly Niet gecategoriseerd 2.5

Lees hieronder de 📖 handleiding in het Nederlandse voor Shelly 2.5 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

USER GUIDE

WARRANTY & WARRANTY TERMS

2 Circuit WiFi Relay Switch

fig. 1

fig. 2

LEGEND:

N - Neutral input (110-230V AC);

Positive input (24-60V DC)

L - Line input (110-230V AC);

Negative input (24-60V DC)

O1 - Output 1;

O2 - Output 2;

SW1 - Switch 1 (input controlling O1);

SW2 - Switch 2 (input controlling O2).

Power supply:

110-230V ±10% 50/60Hz AC

24-60V DC

Max load per channel:

10A/230V, 50/60Hz

Complies with EU standards:

• RE Directive 2014/53/EU

• LVD 2014/35/EU

• EMC 2004/108/WE

• RoHS2 2011/65/UE

Working temperature:

– 40°C up to 40°C

Radio signal power:

1mW

Radio protocol:

WiFi 802.11 b/g/n

Frequency:

2400 – 2500 MHz;

Operational range (depending on local construction):

• up to 50 m outdoors

• up to 30 m indoors

Dimensions (HxWxL):

39 x 36 x 17 mm

Electrical consumption:

< 1 W

The Shelly® Dual WiFi Relay Switch by Allterco Robotics is

intended to be mounted into a standard in-wall console, be-

hind power sockets and light switches in order to control and

monitor the electric power through it, independent for each

channel. Shelly may work as a standalone Device or as an

accessory to a home automation controller.

Technical Information

• Control through WiFi from a mobile phone, PC, automation

system or any other Device supporting HTTP and/or UDP

protocol.

• Microprocessor management.

• Controlled elements: 2 electrical circuits/appliances.

• Controlling elements: 2 relays.

• Shelly may be controlled by an external button/switch.

CAUTION! Danger of electrocution. Mounting the

Device to the power grid has to be performed with

caution.

CAUTION! Do not allow children to play with the

button/switch connected the Device. Keep the De-

vices for remote control of Shelly (mobile phones,

tablets, PCs) away from children.

Introduction to Shelly®

Shelly® is a family of innovative Devices, which allow remote

control of electric appli-ances through mobile phone, PC or

home automation system. Shelly® uses WiFi to connect to

the devices controlling it. They can be in the same WiFi net-

work or they can use remote access (through the Internet).

Shelly® may work standalone, without being managed by a

home automation controller, in the local WiFi network, as well

as through a cloud service, from everywhere the User has

Internet access.

Shelly® has an integrated web server, through which the User

may adjust, control and monitor the Device. Shelly

® has two

WiFi modes - access Point (AP) and Client mode (CM). To

operate in Client Mode, a WiFi router must be located within

the range of the Device. Shelly

® devices can communicate

directly with other WiFi devices through HTTP protocol.

An API can be provided by the Manufacturer. Shelly

® devices

may be available for monitor and control even if the User is

outside the range of the local WiFi network, as long as the

WiFi router is connected to the Internet. The cloud function

could be used, which is activated through the web server of

the Device or through the settings in the Shelly Cloud mobile

application.

The User can register and access Shelly Cloud, using either

Android or iOS mobile applications, or any internet browser

and the web site: https://my.Shelly.cloud/.

Installation Instructions

CAUTION! Danger of electrocution. The mounting/

installation of the Device should be done by a qual-

ied person (electrician).

CAUTION! Danger of electrocution. Even when the

Device is turned off, it is possible to have voltage

across its clamps. Every change in the connection

of the clamps has to be done after ensuring all local power

is powered off/disconnected.

CAUTION! Do not connect the Device to appliances

exceeding the given max load!

CAUTION! Connect the Device only in the way

shown in these instructions. Any other method

could cause damage and/or injury.

CAUTION! Before beginning the installation please

read the accompanying documentation carefully

and completely. Failure to follow recommended

procedures could lead to malfunction, danger to your life or

violation of the law. Allterco Robotics is not responsible for

any loss or damage in case of incorrect installation or oper-

ation of this Device.

CAUTION! Use the Device only with power grid and

appliances which comply with all applicable regu-

lations. short circuit in the power grid or any appli-

ance connected to the Device may damage the Device.

RECOMMENDATION: Тhe Device may be connect-

ed to and may control electric circuits and appli-

ances only if they comply with the respective

standards and safety norms.

RECOMMENDATION: The Device may be connected

with solid single-core cables with increased heat re-

sistance to insulation not less than PVC T105°C.

Initial Inclusion

Before installing/mounting the Device ensure that the grid is

powered off (turned down breakers).

Connect the Relay to the power grid and install it in the con-

sole behind the switch/power socket following the scheme

that suites the desired purpose.

1. 1. Connecting to the power grid and to 2 separately con-

trolled devices (circuits) – g. 1

2. 2. Connecting to the power grid and to motor with 2 rotating

directions and 1 button for controlling the directions of rotation

( for electrical curtains, rollers, garage doors etc.) – g. 2.

CAUTION! The controlled bidirectional electric mo-

tor must have built-in or additionally tted restric-

tors (protectors), to turn the power off upon reaching the

end point or protection against gripping. The anti-grip func-

tion helps in case the garage door encounters an obstacle,

its’ movement stops and the reverse motion is triggered to

release the obstacle.

You may choose if you want to use Shelly with the Shelly

Cloud mobile application and Shelly Cloud service. You can

also familiarize yourself with the instructions for Manage-

ment and Control through the embedded Web interface.

Control your home with your voice

All Shelly devices are compatible with Amazon Echo and

Google Home.

Please see our step-by-step guide on:

https://shelly.cloud/compatibility/Alexa

https://shelly.cloud/compatibility/Assistant

MOBILE APPLICATION FOR

MANAGMENT OF SHELLY®

Shelly Cloud gives you opportunity to control and adjust all

Shelly® Devices from anywhere in the world.

You only need an internet connection and our mobile applica-

tion, installed on your smartphone or tablet.

To install the application please visit Google Play (Android - g.

3) or App Store (iOS - g. 4) and install the Shelly Cloud app.

fig. 3 fig. 4

Registration

The rst time you load the Shelly Cloud mobile app, you have to

create an account which can manage all your Shelly

® devices.

Forgotten Password

In case you forget or lose your password, just enter the e-mail

address you have used in your registration. You will then re-

ceive instructions to change your password.

WARNING! Be careful when you type your e-mail

address during the registration, as it will be used in

case you forget your password.

After registering, create your rst room (or rooms), where you

are going to add and use your Shelly devices.

Shelly Cloud gives you opportunity to create scenes for auto-

matic turning on or off of the Devices at predened hours or

based on other parameters like temperature, humidity, light

etc. (with available sensor in Shelly Cloud).

Shelly Cloud allows easy control and monitoring using a mo-

bile phone, tablet or PC.

Device Inclusion

To add a new Shelly device, install it to the power grid fol-

lowing the Installation Instructions included with the Device.

Step 1

After the installation of Shelly in the console behind the pow-

er socket/light switch and the power is turned on Shelly will

create its own WiFi Access Point (AP).

WARNING: In case the Device has not created its

own WiFi network with SSID like shelly-

switch25-35FA58 check if you have connected Shelly correct-

ly by the schemes described above. If you do not see an active

WiFi network with SSID like shellyswitch25-35FA58, reset the

Device. If the Device has been powered on, you have to restart

by powering it off and on again. After turning the power on,

you have one minute to press 5 consecutive times the button/

switch connected to either input (SW1/SW2). You have to

hear the Relay trigger itself. After the trigger sound, Shelly

should return to AP Mode. If you have physicall access to the

device, you can press and hold the Reset button for 10 sec-

ond, which is placed on the back of the device. Shelly should

return to AP Mode. If not, please repeat or contact our cus-

tomer support at: support@Shelly.cloud

Step 2

Choose “Add Device”.

In order to add more Devices later, use the app menu at the

top right corner of the main screen and click “Add Device”.

Type the name (SSID) and password for the WiFi network, to

which you want to add the Device.

Step 3

If using iOS: you will see the following screen:

Press the home button of your iPhone/iPad/iPod. Open

Settings > WiFi and connect to the WiFi network created by

Shelly, e.g. shellyswitch25-35FA58.

If using Android: your phone/tablet will automatically scan

and include all new Shelly Devices in the WiFi network that

you are connected to.

Upon successful Device Inclusion to the WiFi network you will

see the following pop-up:

Step 4:

Approximately 30 seconds after discovery of any new Devic-

es оn the local WiFi network, а list will be displayed by default

in the “Discovered Devices” room.

Step 5:

Enter Discovered Devices and choose the Device you want to

include in your account.

Step 6:

Enter a name for the Device (in the Device Name eld). Choose a

Room, in which the Device has to be positioned. You can choose

an icon or add a picture to make it easier to recognize. Press

“Save Device”.

Specification

110V-240V

NSW1O1LL02SW2

110-240V AC

NSW1O1LL02SW2

24-60V DC

NSW1O1LL02SW2

2.5

Safety

Max Power Protection: Congure Shelly to turn off when

a dened power consumption is reached. Range: 1-2300W.

After typing the desired power consumption, press Save.

Settings

Power On Default Mode

This sets the default output state when Shelly is powered.

ON: Congure Shelly to turn ON, when it has power.

OFF: Congure Shelly to turn OFF, when it has power.

Restore Last Mode: Congure Shelly to return to last state it

was in, when it has power.

Firmware Update

Update the rmware of Shelly, when a new version is re-

leased.

Time Zone and Geo-location

Enable or Disable the automatic detection of Time Zone and

Geo-location.

Factory Reset

Return Shelly to its factory default settings.

Device Information

Here you can see the:

• Device ID - Unique ID of Shelly

• Device IP - The IP of Shelly in your Wi-Fi network

Edit Device

From here you can edit:

• Device Name

• Device Room

• Device Picture

When you are done, press Save Device.

Additional settings in Roller Shutter mode

Power On Default State

• Open: When powered on, by default, the motor will be in

OPEN state.

• Close: When powered on, by default, the motor will be in

CLOSE state.

• Stop: When powered on, by default, the motor will not

change its position.

OPEN/CLOSE Working Time

This setting allows you to set automatic halt of the move-

ment Open/Close, after a predened time (in seconds).

Cut Off Power: In Roller Shutter mode you can set automatic

halt of movement if the pre-set current draw is exceeded (in

Watts). Allowable power can be set up to 1840W.

Input Buttons Mode:

• Any Button - When you press either of the buttons for

control the motor, it will go in the next step following the

consequence: Open>Stop>Close>Stop>Open> ...

• Open & Close Buttons - Using separate buttons for Open

and Close.

Reverse Controls: Allows you to change the Open/Close

movement.

Some of the features of the Shelly Cloud mobile application

are available at https://my.shelly.cloud/ as well.

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled

through a browser and WiFi connection of a mobile phone,

tablet or PC.

ABBREVIATIONS USED:

Shelly-ID – the unique name of the Device. It consists of 6

or more characters. It may include numbers and letters, for

example 35FA58.

SSID – the name of the WiFi network, created by the Device,

for example Shellyswitch-35FA58.

Access Point (AP) – the mode in which the Device creates its

own WiFi connection point with the respective name (SSID).

Client Mode (CM) – the mode in which the Device is connect-

ed to another WiFi network.

Installation/Initial inclusion

Step 1

Install Shelly to the power grid following the schemes de-

scribed above and place it into the console. After turning the

power on Shelly will create its own WiFi network (AP).

WARNING: If you do not see an active WiFi network

with SSID like shellyswitch25-35FA58, reset the De-

vice. If the Device has been powered on, you have to restart by

powering it off and on again. After turning the power on, you

have one minute to press 5 consecutive times the button/

switch connected to either input (SW1/SW2). You have to

hear the Relay trigger itself. After the trigger sound, Shelly

should return to AP Mode. If you have physicall access to the

device, you can press and hold the Reset button for 10 sec-

ond, which is placed on the back of the device. Shelly should

return to AP Mode. If not, please repeat or contact our cus-

tomer support at: support@Shelly.cloud

Step 2

When Shelly has created an own WiFi network (own AP), with

name (SSID) such as Shellyswitch-35FA58. Connect to it

with your phone, tablet or PC.

Step 3

Type 192.168.33.1 into the address eld of your browser to

load the web interface of Shelly.

General - Home Page

This is the home page of the embedded web interface.

Here you will see information about:

• Current electrical consumption

• Current state (on/off)

• Power Button

• Connection to Cloud

• Present time

• Settings

Safety

Max Power: You can limit the maximum power the socket will

supply. If the pre-set current draw is exceeded, Shelly will turn

the socket off. Allowable power can be set between 1 to 2300W.

Internet/Security

WiFi Mode - Client: Allows the device to connect to an avail-

able WiFi network. After typing the details in the respective

elds, press Connect.

WiFi Mode - Acess Point: Congure Shelly to create a Wi-Fi

Access point. After typing the details in the respective elds,

press Create Access Point.

Cloud: Enable or Disable connection to the Cloud service.

Restrict Login: Restrict the web interface of Shely with a

Username and Password. After typing the details in the re-

spective elds, press Restrict Shelly.

Advanced - Developer Settings: Here you can change the

action execution:

• Via CoAP (CoIOT)

• Via MQTT

WARNING: If you do not see an active WiFi network

with SSID like shellyswitch25-35FA58, reset the De-

vice. If the Device has been powered on, you have to

restart by powering it off and on again. After turning the pow-

er on, you have one minute to press 5 consecutive times the

button/switch connected to either input (SW1/SW2). You

have to hear the Relay trigger itself. After the trigger sound,

Shelly should return to AP Mode. If you have physicall access

to the device, you can press and hold the Reset button for 10

second, which is placed on the back of the device. Shelly

should return to AP Mode. If not, please repeat or contact our

customer support at: support@Shelly.cloud

Settings

Device Type

Here you can set the device type of Shelly:

• Relay - Control over 2 independent circuits

• Roller Shutter - Control over a bi-directional motor

Time Zone and Geo-location

Enable or Disable the automatic detection of Time Zone and

Geo-location.

Firmware Update

Update the rmware of Shelly, when a new version is re-

leased.

Factory Reset: Return Shelly to its factory default settings.

Device Reboot: Reboots the Device.

Managing in Relay Mode

Channel 1/Channel 2 Screen

In this screen you can control, monitor and change the set-

tings for turning the power on and off. You can also see the

current status (electrical load/ power consumption) of the

connected appliance to Shelly, Buttons Settings, On and OFF.

Timer

To manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automati-

cally shutdown after a predened time (in seconds). A value

of 0 will cancel the automatic shutdown.

Auto ON: After turning off, the power supply will be automat-

ically turned on after a predened time (in seconds). A value

of 0 will cancel the automatic power-on.

Weekly Schedule

This function requires an Internet connection.

Shelly may turn on/off automatically at a predened time.

Sunrise/Sunset

This function requires an Internet connection.

Shelly receives actual information about the time of sunrise

and sunset in your area. Shelly may turn on or off automati-

cally at sunrise/sunset, or at a specied time before or after

sunrise/sunset.

Settings

Power On Default Mode

This sets the default output state when Shelly is powered.

ON: Congure Shelly to turn ON, when it has power.

OFF: Congure Shelly to turn OFF, when it has power.

Restore Last Mode: Congure Shelly to return to last state it

was in, when it has power.

SWITCH: Congure Shelly to operate accordingly ti tge state

of the switch (button).

Manual Switch Type

• – When using a button.Momentary

• Toggle Switch – When using a switch.

• – Shelly will change its state on every push.Edge Switch

Managing in Roller Shutter Mode

Roller Screen

In this screen you can control, monitor and change the set-

tings for opening and closing the connected motor to Shelly.

To open the connected motor press “OPEN”.

To close the connected motor press “CLOSE”.

To stop the connected motor press “STOP”.

Weekly Schedule

This function requires an Internet connection.

Shelly may turn on/off automatically at a predened time.

Sunrise/Sunset

This function requires an Internet connection.

Shelly receives actual information about the time of sunrise

and sunset in your area. Shelly may turn on or off automati-

cally at sunrise/sunset, or at a specied time before or after

sunrise/sunset.

Internet/Security

WiFi Mode - Client: Allows the device to connect to an avail-

able WiFi network. After typing the details in the respective

elds, press Connect.

WiFi Mode - Acess Point: Congure Shelly to create a Wi-Fi

Access point. After typing the details in the respective elds,

press Create Access Point.

Cloud: Enable or Disable connection to the Cloud service.

Restrict Login: Restrict the web interface of Shely with a

Username and Password. After typing the details in the re-

spective elds, press Restrict Shelly.

Advanced - Developer Settings: Here you can change the

action execution:

• Via CoAP (CoIOT)

• Via MQTT

WARNING: If you do not see an active WiFi network

with SSID like shellyswitch25-35FA58, reset the De-

vice. If the Device has been powered on, you have to

restart by powering it off and on again. After turning the pow-

er on, you have one minute to press 5 consecutive times the

button/switch connected to either input (SW1/SW2). You

have to hear the Relay trigger itself. After the trigger sound,

Shelly should return to AP Mode. If you have physicall access

to the device, you can press and hold the Reset button for 10

second, which is placed on the back of the device. Shelly

should return to AP Mode. If not, please repeat or contact our

customer support at: support@shelly.cloud

Safety

Max Power: You can limit the maximum power the socket will

supply. If the pre-set current draw is exceeded, Shelly will turn

the socket off. Allowable power can be set between 1 to 2300W.

Obstacle Detection

From here you can set obstacle detection:

• Disabled - this will disable obstacle detection

• While Opening

• While Closing

• While Moving

Obstacle Detection Action

You can select the action that is executed on obstacle detection:

• Stop

• Reverse

Obstacle Detection Treshold

You can set the power treshold on obstacle detection (in Watts).

Obstacle Detection Delay

You can set the delay for obstacle detection activation (in seconds).

When you are done, press Save Device.

Settings

Device Type

Here you can set the device type of Shelly:

• Relay - Control over 2 independent circuits

• Roller Shutter - Control over a bi-directional motor

Shelly Management Settings

Each Shelly can be congured individually. This lets you per-

sonalize each Device in a unique manner, or consistently, as

you choose.

Power On Parameters

This sets the Devices‘ default state when powered from the

power grid.

OPEN: By default when the Device is powered and the con-

nected motor to it will be in OPEN state.

CLOSE: By default when the Device is powered and the con-

nected motor to it will be in CLOSE state.

STOP: By default when the Device is powered and the con-

nected motor to it will not change its state.

OPEN/CLOSE Working Time

This setting allows you to set automatic halt of the move-

ment Open/Close, after a predened time (in seconds).

Input Buttons Mode

• -One Button – On press of the button for control of the mo

tor, it will go in the next step following the consequence:

Open>Stop>Close>Stop>Open

• Open & Close Buttons – Using separate buttons for Open

and Close.

Button Type

• – When using a button.Momentary

• Toggle – When using a switch.

Reverse Control

Allows you to reverse the Open/Close movement.

Time Zone and Geo-location

Enable or Disable the automatic detection of Time Zone and

Geo-location.

Firmware Update

Update the rmware of Shelly, when a new version is re-

leased.

Factory Reset: Return Shelly to its factory default settings.

Device Reboot: Reboots the Device.

Additional Features

Shelly allows control via HTTP from any other Device, home

automation controller, mobile app or server.

For more information about the REST control protocol,

please visit: www.shelly.cloud or send a request to

developers@shelly.cloud

Manufacturer: Allterco Robotics EOOD

Address: Soa, 1407, 103 Cherni Vrah Blvd.

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

http://www.Shelly.cloud

The Declaration of Conformity is available at:

https://Shelly.cloud/declaration-of-conformity/

Changes in the contact data are published by the Manufac-

turer at the ocial website of the Device:

http://www.shelly.cloud

The User is obliged to stay informed for any amendments of

these warranty terms before exercising his/her rights against

the Manufacturer.

All rights to trademarks She® and Shelly

® , and other intel-

lectual rights associated with this Device belong to Allterco

Robotics EOOD.

2019/01/v01

Step 7:

To enable connection to the Shelly Cloud service for remote

control and monitoring of the Device, press “YES” on the fol-

lowing pop-up.

Shelly Devices Settings

After your Shelly device is included in the app, you can control

it, change its settings and automate the way it works.

To switch the Device on and off, use the respective button.Power

To enter at the details menu of the respective Device, simply

click on it’s name. From the details menu you may control the

Device, as well as edit its appearance and settings.

Timer

To manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automati-

cally shutdown after a predened time (in seconds). A value

of 0 will cancel the timer.

Auto ON: After turning off, the power supply will be automat-

ically turned on after a predened time (in seconds). A value

of 0 will cancel the timer.

Weekly Schedule

This function requires an Internet connection.

Shelly may turn on/off automatically at a predened time.

Sunrise/Sunset

This function requires an Internet connection.

Shelly receives actual information about the time of sunrise

and sunset in your area. Shelly may turn on or off automati-

cally at sunrise/sunset, or at a specied time before or after

sunrise/sunset.

Internet/Security

WiFi Mode - Client: Allows the device to connect to an avail-

able WiFi network. After typing the details in the respective

elds, press Connect.

WiFi Mode - Acess Point: Congure Shelly to create a Wi-Fi

Access point. After typing the details in the respective elds,

press Create Access Point.

Cloud: Enable or Disable connection to the Cloud service.

Restrict Login: Restrict the web interface of Shely with a

Username and Password. After typing the details in the re-

spective elds, press Restrict Shelly.

Product specificaties

Merk:	Shelly
Categorie:	Niet gecategoriseerd
Model:	2.5
Kleur van het product:	Black, Blue
LED-indicatoren:	Ja
Wi-Fi-standaarden:	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Stroomverbruik (in standby):	1 W
Certificering:	2014/53/EU • LVD 2014/35/EU • EMC 2004/108/WE • RoHS2 2011/65/UE
Materiaal:	Kunststof
Aantal per verpakking:	1 stuk(s)
Wifi-frequentie:	2.4 GHz
Oververhittingsbeveiliging:	Ja
Frequentie:	50-60 Hz
Op afstand bedienbaar:	Ja
Spanning:	110-230 V
Aantal kanalen:	2 kanalen
Afmetingen (B x D x H):	39 x 36 x 17 mm
Overbelastingsprotectie:	Ja
Maximum indoorbereik:	30 m
Zendvermogen:	1 mW
Wifi:	Ja
AC-ingangsspanning:	110 - 230 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	-40 - 40 °C
Aantal polen:	7
DIN rail bevestiging:	Nee
Aantal modules:	1
Zendbereik:	30 - 50 m
Zonsopkomst/zonsondergang tijd:	Ja
Weekschema:	Ja
Intelligent aan/uit:	Ja