Shelly 1 Handleiding

Shelly Niet gecategoriseerd 1

Lees hieronder de 📖 handleiding in het Nederlandse voor Shelly 1 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 107 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled

through a browser and WiFi connection of a mobile phone,

tablet or PC.

ABBREVIATIONS USED:

Shelly-ID 6– the unique name of the Device. It consists of

or more characters. It may include numbers and letters, for

example 35FA58.

SSID – the name of the WiFi network, created by the Device,

for example shelly1-35FA58.

Access Point (AP) – the mode in which the Device creates its

own WiFi connection point with the respective name (SSID).

Client Mode (CM) – the mode in which the Device is connect-

ed to another WiFi network.

Initial inclusion

Step 1

Install Shelly to the power grid following the schemes de-

scribed above and place it into the console. After turning the

power on Shelly will create its own WiFi network (AP).

WARNING: If you do not see an active WiFi network

with SSID like shelly1-35FA58, reset the Device. If

the Device has been powered on, you have to restart by pow-

ering it off and on again. After turning the power on, you have

one minute to press 5 consecutive times the button/switch

connected to SW. You have to hear the Relay trigger itself.

After the trigger sound, Shelly should return to AP Mode. If

not, please repeat or contact our customer support at: sup-

port@Shelly.cloud

Step 2

When Shelly has created an own WiFi network (own AP), with

name (SSID) such as shelly1-35FA58. Connect to it with your

phone, tablet or PC.

Step 3

Type 192.168.33.1 into the address eld of your browser to

load the web interface of Shelly.

General - Home Page

This is the home page of the embedded web interface. If it

has been set up is correctly, you will see information about:

• Settings menu button

• Current state (on/off)

• Present time

Settings – General Settings

In this menu, you can congure the Shelly device’s work and

connection modes.

WiFi Settings – the WiFi connection settings.

Access Point (AP) Mode: allows the Device to operate as a

WiFi access point. The User can change the name (SSID) and

the password to access the AP. After you have entered the

desired settings, press .Connect

WiFi Client Mode (CM): allows the Device to connect to an

available WiFi network. In order to switch to this mode, the

User must enter the name (SSID) and the password to con-

nect to a local WiFi network. After entering the correct details,

press .Connect

ATTENTION! If you have entered incorrect informa-

tion (wrong settings, usernames, passwords etc.),

you will not be able to connect to Shelly and you have to re-

set the Device.

WARNING: If you do not see an active WiFi net-

work with SSID like shelly1-35FA58, reset the De-

vice. If the Device has been powered on, you have to restart

by powering it off and on again. After turning the power on,

you have one minute to press 5 consecutive times the but-

ton/switch connected to SW. You have to hear the Relay

trigger itself. After the trigger sound, Shelly should return to

AP Mode. If not, please repeat or contact our customer sup-

port at: support@Shelly.cloud

Leave Unprotected - removing the notication for disabled

authorization.

Enable Authentication – you can turn authentication on or

off

This is where you can change your username and password.

You must enter a new username and the new password, then

press to save the changes.Save

Connect to Cloud: you can turn the connection between

Shelly and Shelly Cloud on or off.

Factory reset: Return Shelly to its factory settings.

Firmware Upgrade: Shows present rmware version. If a

newer version is available, you can update your Shelly Device

by clicking Update.

Device Reboot: Reboots the Device.

Managing in Relay Mode

Relay Screen

In this screen you can control, monitor and change the set-

tings for turning the power on and off. You can also see the

current status of the connected appliance to Shelly, Buttons

Settings, On and OFF.

To control Shelly press Relay:

To turn on the connected circuit press “Turn ON”.

To turn off the connected circuit press “Turn OFF”

Press the icon to go to the previous menu.

Shelly Management Settings

Each Shelly can be congured individually. This lets you per-

sonalize each Device in a unique manner, or consistently, as

you choose.

Power On Default State

This sets the relays’ default state when powered from the

power grid.

ON: By default when the Device is powered and the connect-

ed circuit/appliance to it will be powered as well.

OFF: By default the Device and any connected circuit/appli-

ance will not be powered, even when it is connected to the grid.

Restore Last State: By default the Device and the connected

circuit/appliance will be returned to the last state they occu-

pied (on or off) before the last power off/shutdown.

Auto ON/OFF

Automatic powering/shutdown of the socket and the con-

nected appliance:

Auto OFF after: After turning on, the power supply will be

automatically shut down after a predened time (in seconds).

A value of 0 will cancel the automatic shutdown.

Auto ON after: After turning off, the power supply will be au-

tomatically turned on after a predened time (in seconds). A

value of 0 will cancel the automatic start.

Manual Switch Type

• Momentary – When using a button.

• Toggle Switch – When using a switch.

• Edge switch - Change status on every hit.

Sunrise/Sunset hours

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with а working Internet connection.

Shelly receives actual information through the Internet about

the time of sunrise and sunset in your area. Shelly may turn

on or off automatically at sunrise/sunset, or at a specied

time before or after sunrise/sunset.

On/Off schedule

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with working internet connection.

Shelly may turn on/off automatically at a predened time.

Shelly may turn on/off automatically at a predefined time.

Manufacturer: Allterco Robotics EOOD

Address: Soa, 1404, 109 Bulgaria Blvd., . 8

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

http://www.Shelly.cloud

The Declaration of Conformity is available at:

https://Shelly.cloud/declaration-of-conformity/

Changes in the contact data are published by the Manufac-

turer at the ocial website of the Device:

http://www.Shelly.cloud

The User is obliged to stay informed for any amendments of

these warranty terms before exercising his/her rights against

the Manufacturer.

All rights to trademarks She® and Shelly® , and other intel-

lectual rights associated with this Device belong to Allterco

Robotics EOOD.

2018/08/v01

Step 4:

Approximately 30 seconds after discovery of any new Devic-

es оn the local WiFi network, а list will be displayed by default

in the “Discovered Devices” room.

Step 5:

Enter Discovered Devices and choose the Device you want to

include in your account.

Step 6:

Enter a name for the Device (in the Device Name eld). Choose a

Room, in which the Device has to be positioned. You can choose

an icon or add a picture to make it easier to recognize. Press

“Save Device”.

Step 7:

To enable connection to the Shelly Cloud service for remote

control and monitoring of the Device, press “YES” on the fol-

lowing pop-up.

Shelly Devices Settings

After your Shelly device is included in the application, you can

control it, change its settings and automate the way it works.

To switch the Device on and off, use the respective ON/OFF

button.

To enter at the details menu of the respective Device, simply

click on it’s name.

From the details menu you may control the Device, as well as

edit its appearance and settings.

EDIT DEVICE – allows you to change the Device’s name, room

and picture.

DEVICE Settings – allows you to change settings. For ex-

ample, with Restrict login you may enter a username and

password to restrict access to the embedded web interface

in Shelly. You may automate the Device operations from this

menu as well.

Timer

Тo manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automatically

shutdown after a predened time (in seconds). A value of 0 will

cancel the automatic shutdown.

Auto On: After turning off, the power supply will be automati-

cally turned on after a predened time (in seconds). A value of

0 will cancel the automatic power-on.

Weekly schedule

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with working internet connection.

Shelly may turn on/off automatically at a predened time and

day throughout the week. You may add unlimited number of

weekly schedules.

Sunrise/Sunset

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with а working Internet connection.

Shelly receives actual information through the Internet about

the time of sunrise and sunset in your area. Shelly may turn on

or off automatically at sunrise/sunset, or at a specied time

before or after sunrise/sunset.

Settings:

Power On Default Mode

Тhis setting controls whether the Device will supply power

or not the output as a default whenever it is receiving power

from the grid:

ON: When the Device is powered, by default the socket will

be powered.

OFF: Even if the Device is powered, by default the socket will

not be powered.

Restore Last Mode: When power is restored, by default, the

appliance will return to the last state it was in before the last

power off/shutdown.

Button Type

• Momentary - Set Shelly input to be buttons. Push for ON,

push again for OFF.

• Toggle Switch - Set Shelly input to be ip switches, with

one state for ON and another state for OFF.

Firmware Update: Shows present rmware version. If a new-

er version is available, you can update your Shelly Device by

clicking Update.

Factory reset: Remove Shelly from your account and return

it to its factory settings.

Device Information: Here you can see the unique ID of Shelly

and the IP it got from the Wi-Fi network.

Product specificaties

Merk:	Shelly
Categorie:	Niet gecategoriseerd
Model:	1
Soort bediening:	Knoppen
Kleur van het product:	Wit
Breedte:	70 mm
Diepte:	12 mm
Hoogte:	70 mm
Materiaal behuizing:	Kunststof
Aan/uitschakelaar:	Ja
Montagewijze:	Muur
Aantal per verpakking:	1 stuk(s)
Aantal knoppen:	1
Aantal kanalen:	1 kanalen
Bedrijfstemperatuur (T-T):	-20 - 70 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent
Number of devices supported:	1
Type aan-/uitschakelaar:	2-weg
Fluorescerend:	Nee