Shelly EM Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Shelly EM (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 117 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
USER GUIDE
2 Channel WiFi Energy Meter
LEGEND:
N - Neutral input (110-230V AC);
L - Line input (110-230V AC);
O - Output for contactor control (max 2A);
P1+ - Positive connection of current transformer 1
P1- - Negative connection of current transformer 1
P2+ - Positive connection of current transformer 2
P2- - Negative connection of current transformer 2
The Dual WiFi Energy Meter, Shelly® EM by Allterco Robotics
is intended to be mounted into a standard in-wall console or
next to the breakers, in order to monitor the electric power
through it, independent for each channel and heavy-duty con-
tactor control. Shelly may work as a standalone Device or as
an accessory to a home automation controller.
Purpose of control: Operating
Construction of control: Independently mounted
Type 1.B Action
Pollution Degree 2
Impulse Voltage: 4000 V
Power supply:
110-230V ±10% 50/60Hz AC
Max measurement per channel:
120A/230V
Relay Max Load:
2A/230V
Complies with EU standards:
-RE Directive 2014/53/EU
-LVD 2014/35/EU
-EMC 2004/108/WE
-RoHS2 2011/65/UE
Working temperature:
– 40°C up to 40°C
Radio signal power:
1mW
Radio protocol:
WiFi 802.11 b/g/n
Frequency:
2400 – 2500 MHz;
Operational range (depending on local construction):
-up to 50 m outdoors
-up to 30 m indoors
Dimensions(HxWxL):
39 x 36 x 17 mm
Electrical consumption:
< 1 W
Technical Information
Control through WiFi from a mobile phone, PC, automation
system or any other Device supporting HTTP and/or UDP
protocol.
Microprocessor management.
CAUTION! Danger of electrocution. Mounting the Device
to the power grid has to be performed with caution.
CAUTION! Do not allow children to play with the button/
switch connected the Device. Keep the Devices for remote
control of Shelly (mobile phones, tablets, PCs) away from
children.
Introduction to Shelly®
Shelly® is a family of innovative Devices, which allow remote
control of electric appli-ances through mobile phone, PC or
home automation system. Shelly® uses WiFi to connect to
the devices controlling it. They can be in the same WiFi net-
work or they can use remote access (through the Internet).
Shelly® may work standalone, without being managed by a
home automation controller, in the local WiFi network, as well
as through a cloud service, from everywhere the User has
Internet access.
Shelly® has an integrated web server, through which the User
may adjust, control and monitor the Device. Shelly
® has two
WiFi modes - access Point (AP) and Client mode (CM). To
operate in Client Mode, a WiFi router must be located within
the range of the Device. Shelly
® devices can communicate
directly with other WiFi devices through HTTP protocol.
An API can be provided by the Manufacturer. Shelly
® devices
may be available for monitor and control even if the User is
outside the range of the local WiFi network, as long as the
WiFi router is connected to the Internet. The cloud function
could be used, which is activated through the web server of
the Device or through the settings in the Shelly Cloud mobile
application.
The User can register and access Shelly Cloud, using either
Android or iOS mobile applications, or any internet browser
and the web site: https://my.Shelly.cloud/.
Installation Instructions
CAUTION! Danger of electrocution! The mounting/ in-
stallation of the Device should be done by a qualied person
(electrician).
CAUTION! Danger of electrocution! Do not connect the
current transformer clamp to the Line, before wiring it to
Shelly EM. Even if only the current transformer is connected,
there might be high voltage accross its connection cables.
CAUTION! Danger of electrocution. Even when the Device
is turned off, it is possible to have voltage across its clamps.
Every change in the connection of the clamps has to be done
after ensuring all local power is powered off/disconnected.
-CAUTION! Do not connect the Device to appliances ex
ceeding the given max load!
CAUTION! Connect the Device only in the way shown in
these instructions. Any other method could cause damage
and/or injury.
CAUTION! Before beginning the installation please read
the accompanying documentation carefully and completely.
Failure to follow recommended procedures could lead to mal-
function, danger to your life or violation of the law. Allterco
Robotics is not responsible for any loss or damage in case of
incorrect installation or operation of this Device.
CAUTION! Use the Device only with power grid and ap-
pliances which comply with all applicable regulations. short
circuit in the power grid or any appliance connected to the
Device may damage the Device.
RECOMMENDATION: Тhe Device may be connected to
and may control electric circuits and appliances only if they
comply with the respective standards and safety norms.
Initial Inclusion
Initial Inclusion
Before installing/mounting the Device ensure that the grid is
powered off (turned down breakers).
Connect Shelly EM to the power grid and install it in the con-
sole following the scheme that suites the desired purpose.
You may choose if you want to use Shelly with the Shelly
Cloud mobile application and Shelly Cloud service. You can
also familiarize yourself with the instructions for Manage-
ment and Control through the embedded Web interface.
Control your home with your voice
All Shelly devices are compatible with Amazon Echo and
Google Home.
Please see our step-by-step guide on:
https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant
MOBILE APPLICATION FOR
MANAGMENT OF SHELLY®
Shelly Cloud gives you opportunity to control and adjust all
Shelly® Devices from anywhere in the world.
You only need an internet connection and our mobile applica-
tion, installed on your smartphone or tablet.
To install the application please visit Google Play (Android - g.
3) or App Store (iOS - g. 4) and install the Shelly Cloud app.
Registration
The rst time you load the Shelly Cloud mobile app, you have to
create an account which can manage all your Shelly
® devices.
Forgotten Password
In case you forget or lose your password, just enter the e-mail
address you have used in your registration. You will then re-
ceive instructions to change your password.
WARNING! Be careful when you type your e-mail address
during the registration, as it will be used in case you forget
your password.
After registering, create your rst room (or rooms), where you
are going to add and use your Shelly devices.
Shelly Cloud gives you opportunity to create scenes for auto-
matic turning on or off of the Devices at predened hours or
based on other parameters like temperature, humidity, light
etc. (with available sensor in Shelly Cloud).
Shelly Cloud allows easy control and monitoring using a mo-
bile phone, tablet or PC.
Device Inclusion
To add a new Shelly device, install it to the power grid fol-
lowing the Installation Instructions included with the Device.
Step 1
After the installation of Shelly in the console behind the pow-
er socket/light switch and the power is turned on Shelly will
create its own WiFi Access Point (AP).
WARNING: In case the Device has not created its own WiFi
network with SSID like shellyem-35FA58 check if you have
connected Shelly correctly by the schemes described above.
If you do not see an active WiFi network with SSID like shelly-
em-35FA58, reset the Device. In order to reset the device,
you will need physical access to it. On the back of the device,
you will see a button. Press and hold it for 10 seconds. Shelly
should return to AP Mode. If not, please repeat or contact our
customer support at: support@Shelly.cloud
Step 2
Choose “Add Device”.
In order to add more Devices later, use the app menu at the
top right corner of the main screen and click Add Device”.
Type the name (SSID) and password for the WiFi network, to
which you want to add the Device.
Step 3
If using iOS: you will see the following screen:
Press the home button of your iPhone/iPad/iPod. Open
Settings > WiFi and connect to the WiFi network created by
Shelly, e.g. shellysem-35FA58.
If using Android: your phone/tablet will automatically scan
and include all new Shelly Devices in the WiFi network that
you are connected to.
Upon successful Device Inclusion to the WiFi network you will
see the following pop-up:
Step 4:
Approximately 30 seconds after discovery of any new Devic-
es оn the local WiFi network, а list will be displayed by default
in the “Discovered Devices” room.
Specication
120A 50A
N
L
NOLP2-P2+P1-P1+
g. 3 g. 4
The Embedded Web Interface
Еven without the mobile app, Shelly can be set and controlled
through a browser and WiFi connection of a mobile phone,
tablet or PC.
ABBREVIATIONS USED:
Shelly-ID the unique name of the Device. It consists of 6
or more characters. It may include numbers and letters, for
example 35FA58.
SSID – the name of the WiFi network, created by the Device,
for example Shellyem-35FA58.
Access Point (AP) – the mode in which the Device creates its
own WiFi connection point with the respective name (SSID).
Client Mode (CM)the mode in which the Device is connect-
ed to another WiFi network.
Installation/Initial inclusion
Step 1
Install Shelly to the power grid following the schemes de-
scribed above and place it into the console. After turning the
power on Shelly will create its own WiFi network (AP).
WARNING: In case the Device has not created its own WiFi
network with SSID like shellyem-35FA58 check if you have
connected Shelly correctly by the schemes described above.
If you do not see an active WiFi network with SSID like shelly-
em-35FA58, reset the Device. In order to reset the device, you
will need physical access to it. On the back of the device, you
will see a button. Press and hold it for 10 seconds. Shelly
should return to AP Mode. If not, please repeat or contact our
customer support at: support@Shelly.cloud
Step 2
When Shelly has created an own WiFi network (own AP), with
name (SSID) such as Shellyem-35FA58. Connect to it with
your phone, tablet or PC.
Step 3
Type 192.168.33.1 into the address eld of your browser to
load the web interface of Shelly.
General - Home Page
This is the home page of the embedded web interface.
Here you will see information about:
Current electrical consumption of Channel 1
Power Factor of Channel 1
Current electrical consumption of Channel 2
Power Factor of Channel 2
Voltage
Power Button
Connection to Cloud
Present time
Settings
Timer
To manage the power supply automatically, you may use:
Auto OFF: After turning on, the power supply will automatical-
ly shutdown after a predened time (in seconds). A value of
0 will cancel the timer.
Auto ON: After turning off, the power supply will be automat-
ically turned on after a predened time (in seconds). A value
of 0 will cancel the timer.
Weekly Schedule
This function requires an internet connection.
Shelly receives actual information about the time of sunrise
and sunset in your area.
Shelly may turn on/off automatically at a predened time, at
sunrise/sunset, or at a specied time before or after sunrise/
sunset.
Internet/Security
WiFi Mode - Client: Allows the device to connect to an avail-
able WiFi network. After typing the details in the respective
elds, press Connect.
WiFi Client Backup: Allows the device to connect to an al-
ternative WiFi network, if the primary is not available. After
typing the details in the respective elds, press Set.
WiFi Mode - Access Point: Congure Shelly to create a Wi-Fi
Access point. After typing the details in the respective elds,
press Create Access Point.
Restrict Login: Restrict the web interface of Shelly with a
Username and Password. After typing the details in the re-
spective elds, press Restrict Shelly.
SNTP Server: You can change the default SNTP server. Enter
the address, and click Save.
Advanced - Developer Settings: Here you can change the
action execution:
Via CoAP (CoIOT)
Via MQTT
Cloud: Enable or Disable connection to the Cloud service.
Settings
Power On Default Mode
This sets the default output state when Shelly is powered.
ON: Congure Shelly to turn ON, when it has power.
OFF: Congure Shelly to turn OFF, when it has power. Restore
Last Mode: Congure Shelly to return to last state it was in,
when it has power.
Current Transformer Type:
You can select the type of current transformer that you are
using.
Firmware Update
Update the rmware of Shelly, when a new version is re-
leased.
Time Zone and Geo-location
Enable or Disable the automatic detection of Time Zone and
Geo-location.
Set Date/Time
You can manually set the Date and time for your Shelly device.
Factory Reset: Return Shelly to its factory default settings.
Device Reboot: Reboots the Device.
Device Info: Shows your device ID.
In Client Mode shows also your WiFi network name and WiFi
signal strength.
Description of Shelly EM values:
1. Power Consumption
This is the power which is actually consumed or utilized in an
AC Circuit is called True power, Active power or Real power.
It is measured in kilo watt (kW) or mega Watt (MW). It is the
actual outcomes of the electrical system which runs the elec-
tric circuits or loads. This is the energy which you are paying.
It is shown in blue color in the history graph.
If you have solar panel and sell energy, you will see this power
with “negative” value. It is shown in green color in the history
graph.
2. Reactive power:
This is the power that ows back and forth, it moves in both
the direction in the circuit or react upon itself. The Reac-
tive power is measured in Volt-Ampere reactive (VAR), Kilo
Volt-Ampere reactive (VAR) or Mega Volt-Ampere reactive
(MVAR). You are not being charged for this energy.
3. Power Factor:
The power factor of an AC electrical circuit is dened as the
ratio of the real power absorbed by the load to the apparent
power owing in the circuit, and is a dimensionless number
in the closed interval of −1 to 1. A power factor of less than 1
indicates the voltage and current are not in phase, reducing
the instantaneous product of the two. In a perfect situation
the Power Factor is close to 1.
4. Voltage:
Voltage, also called electromotive force, is a quantitative ex-
pression of the potential difference in charge between two
points in an electrical eld.
You can download your history by going to
https://my.shelly.cloud/ in a browser on a PC.
Manufacturer: Allterco Robotics EOOD
Address: Soa, 1407, 103 Cherni Vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
http://www.Shelly.cloud
The Declaration of Conformity is available at:
https://Shelly.cloud/declaration-of-conformity/
Changes in the contact data are published by the Manufac-
turer at the ocial website of the Device:
http://www.shelly.cloud
The User is obliged to stay informed for any amendments of
these warranty terms before exercising his/her rights against
the Manufacturer.
All rights to trademarks of Shelly® , and other intellectual
rights associated with this Device belong to Allterco Robotics
EOOD.
Details menu
Here you will see the momentary:
Consumption - in Watts
Voltage -in Volts
Reactive power – in Volt-Ampere Reactive (VAR)
Power Factor – in the range of -1 to 1
Below that you will see the history graph for the last year for:
Consumption*
Voltage –with a lowest and highest measurement
*If you have connected your solar panel to Shelly EM, it will be
shown in green color.
Settings
Timer
Manage the power supply automatically:
Auto OFF: After turning on, the power supply will automati-
cally shutdown after a predened time (in seconds). A value
of 0 will cancel the timer.
Auto ON: After turning off, the power supply will be automat-
ically turned on after a predened time (in seconds). A value
of 0 will cancel the timer.
Weekly Schedule
This function requires an internet connection.
Shelly receives actual information about the time of sunrise
and sunset in your area.
Shelly may turn on/off automatically at a predened time, at
sunrise/sunset, or at a specied time before or after sunrise/
sunset.
Internet/Security
WiFi Mode - Client: Allows the device to connect to an avail-
able WiFi network. After typing the details in the respective
elds, press Connect.
WiFi Client Backup: Allows the device to connect to an al-
ternative WiFi network, if the primary is not available. After
typing the details in the respective elds, press Set.
WiFi Mode - Access Point: Congure Shelly to create a Wi-Fi
Access point. After typing the details in the respective elds,
press Create Access Point.
Cloud: Enable or Disable connection to the Cloud service.
Restrict Login: Restrict the web interface of Shely with a
Username and Password. After typing the details in the re-
spective elds, press Restrict Shelly.
Settings
Current Transformer Type:
You can select the type of current transformer that you are using.
Power On Default Mode
This sets the default output state when Shelly is powered.
ON: Congure Shelly to turn ON, when it has power.
OFF: Congure Shelly to turn OFF, when it has power. Restore
Last Mode: Congure Shelly to return to last state it was in,
when it has power.
Firmware Update
Update the rmware of Shelly, when a new version is released.
Time Zone and Geo-location
Enable or Disable the automatic detection of Time Zone and
Geo-location.
Factory Reset
Return Shelly to its factory default settings.
Device Information
Here you can see the:
Device ID - Unique ID of Shelly
Device IP - The IP of Shelly in your Wi-Fi network
Device Type – The type of your Shelly device
WiFi Name – the Name (SSID) of the WiFi network to which
your Shelly is connected
WiFi Signal - the Signal strength of the WiFi network to
which your Shelly is connected
Edit Device
From here you can edit:
Device Name
Device Room
Device Picture
When you are done, press Save Device.
Some of the features of the Shelly Cloud mobile application
are available at https://my.shelly.cloud/ as well.
Step 5:
Enter Discovered Devices and choose the Device you want to
include in your account.
Step 6:
Enter a name for the Device (in the Device Name eld). Choose a
Room, in which the Device has to be positioned. You can choose
an icon or add a picture to make it easier to recognize. Press
“Save Device”.
Step 7:
To enable connection to the Shelly Cloud service for remote
control and monitoring of the Device, press “YES” on the fol-
lowing pop-up.
Shelly Devices Settings
After your Shelly device is included in the app, you can control
it, change its settings and automate the way it works.
To switch the relay of the Device on and off, use the respec-
tive Power button. To enter at the Details menu of the respec-
tive Device, simply click on its name. From the details menu
you may control the Device, as well as edit its appearance
and settings.


Product specificaties

Merk: Shelly
Categorie: Niet gecategoriseerd
Model: EM

Heb je hulp nodig?

Als je hulp nodig hebt met Shelly EM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Shelly

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd