Princeton Tec Point MPLS Handleiding

Princeton Tec Zaklamp Point MPLS

Lees hieronder de 📖 handleiding in het Nederlandse voor Princeton Tec Point MPLS (2 pagina's) in de categorie Zaklamp. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Reverse Picatinny Mount MOLLE Mount

MPLS

Helmet Mount Picatinny Mount

Picatinny Mount

MODULAR PERSONAL

L I G HT I NG SYST E M

Battery Installation

3. Optional Reverse Picatinny mount – Will

work in ARC dovetail rails. Slide Reverse

Picatinny into ARC Dovetail rail to desired

position and secure in place with center

anti-slip lock screw. DO NOT OVERTIGHTE

this screw.

4. Optional Picatinny mount – Remove the

center through bolt from the side of the

Picatinny base mount. Slide Picatinny to

desired position and insert side locking blot

aligning with any slot in Picatinny rail and

tighten to clamp in place. DO NOT

OVERTIGHTEN this screw.

USA Lifetime Warranty– International

10-Year Warranty

Princeton Tec reserves the right to change produc

specifications without notice.

Return Policy

If your light fails to operate, follow these simple

steps:

1) Check batteries. Replace if necessary.

2) Contact Princeton Tec customer service at

800-257-9080 to request an RMA number to

send your light in for repair or replacement. No

warranty repairs will be accepted without an

RMA number.

3) Return the light without batteries to:

Princeton Tec, 5198 Rt. 130, Bordentown, NJ

08505. Postage due and freight collect items

will not be accepted.

Battery Installation

See Battery Installation Diagram

White, Blue or Green LED

• (2) CR2016 Coin Cells - 6V

Infrared and Red LED

• (1) CR2032 Coin Cell - 3V

Princeton Tec cares about the environment and

recommends recycling batteries. For more

information about battery recycling, please go

to: www.batteryrecycling.com

To install the batteries, Rotate Light unit out of

Ratchet Base. Lift Tab of Battery Door on the

underside of light unit to expose Coin cell(s)

Install Coin cell(s) batteries with the + positive

side facing up. Improper installation of the

batteries will damage the light and void the

warranty.

Replace the battery door with the lift tab properly

aligned with lift tab slot of the housing. Press door

firmly in place making sure it is all the way seated

in place.

WARNING

Never mix fresh and used batteries.

Never mix different battery brands or chemistry

types.

Always remove drained batteries immediately.

Remove batteries during long periods of storage.

Switch Operation – See Operation diagram

Modes (Low then High) are selected by pressing

and releasing the button within 1.6 seconds of

the previous button press.

There are three ways to turn the MPLS off.

1. You can cycle through the modes within 1.6

seconds of the initial button press until you reach off.

2. Or if more than 1.6 seconds has passed since

the previous button press the next press of

the button will turn the light off.

3. Or when turning the light on, press and hold

the button for momentary light output (in Low

mode) and after 1.6 seconds has passed,

releasing the button will turn the light off.

Troubleshooting

If the MPLS fails to light:

• Check the batteries for proper installation.

• Replace batteries if proper installation is

confirmed.

• This light has been designed to be water

resistant. Check the light for water

contamination on the circuit board. The light

will resume normal operation once any water

is shaken or blown out and the light is left

open until completely dry. If the light has been

contaminated with salt water, flush the unit with

fresh water and dry as described above.

There are four different Base mounts your MPLS

light will attach to. Helmet Mount, Mollie Vest

mount, Picatinny and Reverse Picatinny mount.

1. Helmet mount – Back the screw out to the

end of screw is flush with metal U-clip. Slide

the exposed U-clip on the bottom edge of

your Helmet with the metal clip on the inside

and the plastic ratchet mount exposed on the

outside of your Helmet. Holding Mount firmly

upward, tighten center slotted screw until it

stops.

2. MOLLE Vest mount – Slide metal back clip

inside any MOLLE strap position, pinch Mollie

strap to hook the lower end of the metal clip

onto the strap. 2010

Product specificaties

Merk:	Princeton Tec
Categorie:	Zaklamp
Model:	Point MPLS
Kleur van het product:	Olijf
Gewicht:	17 g
Aantal lampen:	1 lampen
Soort lamp:	LED
Vermogen lamp:	- W
Waterdicht:	Nee
Ondersteund aantal accu's/batterijen:	2
Levensduur accu/batterij:	36 uur
Lichtstroom:	10 lm
Batterijtechnologie:	Lithium
Type batterij:	2016 Coin
Type zaklamp:	Universele zaklamp