Labelmate LD-100-U Handleiding

Labelmate Niet gecategoriseerd LD-100-U

Lees hieronder de 📖 handleiding in het Nederlandse voor Labelmate LD-100-U (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MAINTENANCE:

Keep the Label Sensor and Stripper Bar clean, following instructions page 1.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or ﬁtness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

LABELMATE SPRL

290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

LD- -U / LD- -U 100 200

Powered Label Dispenser

• High-Low Speed Select

• Adjustable Label Sensor

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

• User Manual (this document)

• Label Dispenser Unit

• Power Supply Module

VERY IMPORTANT:

• Keep Label Sensor Eye clean. Wipe with a soft cloth occasionally. Be careful not

to damage the sensor. Do not use any chemical on the Sensor.

• Keep Tape Stripper Bar and Web Guide Bars clean. Use isopropyl alcohol or

"Goo- -up can Gone"™ to clean adhesive residue from parts. Adhesive build

cause malfunction and damage to your unit.

SPECIFICATIONS:

Weight of the machine: 5 Kg.

Max. Label Roll Weight: 4.5 Kg.

Max. Label Roll Size: 220 mm diameter 300 mm with - . –LD DE

Power Supply: Input: 220-240VAC -60Hz. –50

Output: 15VDC-4.33A

Retain the Shipping Container and Packaging for Storage and Transport.

IMPORTANT INFORMATION:

• This product is a label dispenser. It is only to be used to dispense labels of the

recommended dimensions and weight in an indoor, dry environment.

• The machine has to be unplugged before any manipulation.

• The machine is to be used on a ﬂat surface, if the surface is not ﬂat, it is to be ﬁxed

using the holes in the base plate.

• Do not leave the power cable in a passageway.

• The ambient light of the working area needs to be suﬃcient to avoid any risk.

• The dispenser can be used in ambient temperatures of +2°C to 40°C.

• For operators working long hours on the machine, it is recommended to wear glasses

protecting from the light (e.g. light sunglasses).

• All measures have been taken to minimise risks of injuries with the take-up shaft but

the operator has to be careful when manipulating the bail.

• Connection of the machine to the power source must respect local and European

legislations.

SET-UP AND USE:

1. Make sure the Power Switch is in the “OFF” position.

2. Set your LD-100-U or LD- -U in place and plug the cord from the Power Supply 200

Module into the Power Input Jack on the rear of the Unit.

3. Connect the Power Supply Module to a suitable power source.

4. Place your roll of labels on the Label Roll Holder & slide the Roll Edge Guide(s) to

the width of your label web. The Label Web can be positioned from side to side as

required to ensure that the label lines up with the reﬂective Sensor.

5. Thread the label web between the Stripper Bar and the round Guide Rod directly

above it. See the Label Threading Path illustration.

6. Pull the label web under (or over) the round Web Guide and slide the width

adjusters to the width of the web.

7. Loop the web UNDER the Wire Bail on the Take-Up Shaft as shown in the

illustration.

8. Slightly loosen the Label Sensor Lock Knob, until you can just rotate the Sensor.

Point the sensor up so it is pointing at the bottom of the Stripper Bar. Place the

Power Switch in the “LOW” position. Slowly rotate the Sensor down until the label

begins to advance. Continue to rotate the Sensor slowly until the desired label

length is protruding. Retighten the Lock Knob securely.

9. When dispensing transparent labels, it is recommended to place the sensor as

close to the labels as possible.

10. Use “HIGH” or “LOW” Switch setting to select the desired speed.

11. IMPORTANT Pull labels UP when removing them. –If excess dust or dirt

accumulates on the Label Sensor Eye the Dispenser may not sense labels correctly.

Use a cloth or paper towel dampened with water to gently clean the Label Sensor.

12. Do not use any chemicals on the sensor.

13. Optional Flanges for the inside and outside of the label roll are available (Order LD-

FLANGES. Set of two Flanges). These Flanges are recommended for narrow or

loosely wound labels that may have a tendency to fall oﬀ the roll.

OPTIONAL LABEL COUNTER: The optional Label Counter will add one count to the

displayed number for each label that is dispensed. This Option is available only factory

installed in new Units.

When the LD- -U/LD- -100 200 U is first turned on, it will display a count of “1” or it will

display the number from the previous count. You can reset the Label Counter to zero

(“0”) by pressing the “R” Reset Button.

FOR YOUR SAFETY:

Switch oﬀ device before removing the take-up shaft.

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

Label Threading Path

Product specificaties

Merk:	Labelmate
Categorie:	Niet gecategoriseerd
Model:	LD-100-U
Gewicht:	5000 g
Stroomvoorziening:	120 x 230 VAC, 50/60 Hz
Afmetingen (B x D x H):	305 x 229 x 229 mm
Afmetingen papier:	115 x 150 mm