Labelmate S-100S Handleiding

Labelmate Niet gecategoriseerd S-100S

Lees hieronder de 📖 handleiding in het Nederlandse voor Labelmate S-100S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MAINTENANCE:

Your S-100 / S- 200 requires no maintenance.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or ﬁtness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

Label Slitter

• In-Line or Oﬀ-Line Use.

• Optional Pre-set Counter.

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

• User Manual (this document)

• Slitter Unit

• If ordered, Optional Counter with Power Supply Module (Factory

installed)

SPECIFICATIONS:

Weight of the machine: 7,1Kg to 8,5Kg depending on model.

Power Supply Counter : Input: 220-240VAC -60Hz. –50

Output: 1.5V 12V DC. 300mA. –

Retain the Shipping Container and Packaging for Storage and Transport

WARNING !

Use caution and common sense to avoid personal injury or

damage to clothing when working with cutting blades or

around exposed blade surfaces.

IMPORTANT INFORMATION:

• This product is a label slitter. It is only to slit rolls of labels in an indoor, dry environment.

• Use extreme caution when manipulating the blades.

• Do not adjust the blades while slitting.

• The machine is to be used on a ﬂat surface, if the surface is not ﬂat, it is to be ﬁxed using

the holes in the base plate.

• Do not leave the power cable of the counter in a passageway.

• The ambient light of the working area needs to be suﬃcient to avoid any risk.

• Connection of the machine to the power source must respect local and European

legislations

SET-UP AND USE:

1. Place the S-100 or S-200 Label Slitter so that it is perpendicular to the web of labels

to be slit. Observe the Paper Path Label on the Slitter.

2. Loosen the Black Knob holding the red Blade Cover Shield and raise the Shield to

the vertical position.

3. Rotate the Black Knob assembly approximately one-half turn so it is facing down and

out of the way.

4. Rotate the blade holder shaft slightly to lift the Blade See WARNING NOTICE above.

Holders from the round white Nylon Fixed Paper Guide.

5. Being careful to avoid contact with the cutting blades feed the label web under the

Rotating Paper Guide and over the Fixed Paper Guide.

6. Adjust the position of the rings on the Rotating and Fixed Paper Guides to the width of

your label web. Only ﬁnger tighten the screws. If you have the PC-1 Preset Counter,

the labels must pass through the sensor slot.

7. Pull the label web through and aﬃx it to the label rewind core on the Label Rewinder.

8. Being careful to avoid contact with the cutting Blades, adjust the position of the Blade

Holders as desired. To do this, loosen the white Nylon set screw of the Blade Holders

and slide the Blade Holders in or out as needed. Finger tighten the white Nylon set

screw to hold the adjustment. Do not over tighten.

9. Extend the cutting blades as required using the black click-stop adjustment on the

side of each knife. THE BLADE TIP MUST EXTEND WELL PAST THE ROUND

WHITE NYLON ROD SO THE CUTTING BLADE ITSELF IS RESTING ON THE

WHITE NYLON.

10. Being careful to avoid contact with the cutting Blades, rotate the Blade Holders

down until the cutting blades rest lightly on the Fixed Paper Guide. The Blades

must pierce the label

11. Now lower the red Blade Shield to the Blade Holders.

12. Secure the red Blade Shield by rotating the small Black Knob assembly into the slot

on the red Blade Shield and tightening the small Black Knob until it is snug. The

Blades will press into the Nylon bar.

CAUTION: DO NOT OVERTIGHTEN.

NOTE: If the red Blade Shield does not press on all Blade Holders equally, loosen

the mounting nuts for the Blade Shield Hinge on the Chassis and reposition them

until the Blade Shield is “level” with the Blade Holders.

13. Start the Label Rewinder and the printer (if used). Adjust the speed of the Label

Rewinder as required. See the CAT-3 User Manual for details.

14. To make ﬁne adjustments to the position of the blades over the web AS A SET, use

the large black adjustment knob marked “LIFT BLADES TO ADJUST.” NOTE:

ALWAYS LIFT THE BLADES FROM THE LABEL WEB TO MAKE

ADJUSTMENTS. USE CAUTION TO AVOID CONTACT WITH THE CUTTING

BLADES.

15. When the slitting action becomes impaired because of dull Cutting Blades, the

Blades can be clicked down within their holders to expose an unused area of the

cutting blade. In this way, blade life is greatly extended. If desired, the used up part

of the Blade can be snapped oﬀ at one of the score lines.

16. When the cutting blades are completely worn out, replace them with LABELMATE

HSB-10 High Speed Cutting Blades.

OPTIONAL PC-1 PRESET COUNTER SET-UP:

1. For Auto-Stop, plug a Control Cable (with 3.5mm plugs at each end) between the

External Halt Jack on the PC-1 and the “EXTERNAL HALT CONTROL” Jack on the

CAT-3 Label Rewinder.

2. The Counter is pre-programmed as a Count-Up Preset Counter. For other modes,

refer to the Counter Data Sheet that is part of the documentation package.

3. Successively press the Buttons below each digit to enter the desired count and then

press the Red Reset/Enter Button.

4. Pull a short strip of labels back and forth through the Label Sensor Gap and observe

the count on the Counter increasing.

5. When the preset number of Labels is reached, the Counter will stop the S-100/S-200

and the External Halt Control Relay will open, serving as a “Halt” Command for the

CAT-3 Label Rewinder. Press the red Reset/Enter Button to reset the count & restart

the CAT-3.

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

Product specificaties

Merk:	Labelmate
Categorie:	Niet gecategoriseerd
Model:	S-100S

Heb je hulp nodig?

Als je hulp nodig hebt met Labelmate S-100S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Labelmate

Labelmate UCAT-40 Handleiding

9 Mei 2023

Labelmate CAT-4 Handleiding

9 Mei 2023

Labelmate UCAT-1-CHUCK Handleiding

9 Mei 2023

Labelmate S-100S Handleiding

9 Mei 2023

Labelmate CAT-4-ACH Handleiding

9 Mei 2023

Labelmate Count-200 Handleiding

9 Mei 2023

Labelmate Count-100 Handleiding

9 Mei 2023

Labelmate CAT-40G Handleiding

9 Mei 2023

Labelmate LD-100-U Handleiding

9 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Inglesina Welcome Pad Handleiding

22 December 2024

Inglesina Front Handleiding

22 December 2024

Inglesina Newborn Winter Muff Handleiding

22 December 2024

Inglesina Stroller Winter Muff Handleiding

22 December 2024

Protector AS-5030.3 V2 Handleiding

21 December 2024

Sabrent AU-MMCW Handleiding

21 December 2024

Sabrent AU-2X35 Handleiding

21 December 2024

Sabrent CB-RS232 Handleiding

21 December 2024

Owon 500W Handleiding

21 December 2024

Owon 300W Handleiding

21 December 2024