Labelmate UCAT-1-CHUCK Handleiding

Labelmate Niet gecategoriseerd UCAT-1-CHUCK

Lees hieronder de 📖 handleiding in het Nederlandse voor Labelmate UCAT-1-CHUCK (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MAINTENANCE:

Your UCAT- 40 requires no maintenance.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or ﬁtness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

SPRL

290? Chauss2e de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

Heavy-Duty "UCAT"

On-Demand Powered Label winderUn

• Dual Torque Range and Direction

Controls

• Constant Adjustable TorqueTM

"CAT" technology

• Adjustable Speed Control

• Precise Variable Torque Control

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

• User Manual (this document)

• UCAT-40 Drive Unit

• Power Supply Module

• LABELMATE "Quick- -Locking Core Chuck Chuck" ™ Quick

• Allen Wrench

• Plastic Inner Flange Plate

• Control Arm with setscrews and shaft screw.

Retain the Shipping Container and Packaging for Storage and Transport

SPECIFICATIONS:

Weight of the machine: 12,9Kg.

Max. Label Roll Weight: 14Kg.

Max. Label Roll Diam: 400mm.

Start/Stop: ON/OFF/ON Direction Switch

Power Supply: Input: 220-240VAC -60Hz. –50

Output: 15V DC.

IMPORTANT INFORMATION:

• This product is a label winder. It is only to be used unwind labels of the un to

recommended dimensions and weight in an indoor, dry environment.

• The machine has to be unplugged before any manipulation.

• The machine is to be used on a ﬂat surface, if the surface is not ﬂat, it is to be ﬁxed using

the holes in the base plate.

• Do not leave the power cable in a passageway.

• The ambient light of the working area needs to be suﬃcient to avoid any risk.

• The unwinder can be used in ambient temperatures of +2°C to 40°C.

• Connection of the machine to the power source must respect local and European

legislations.

SET-UP:

1. Install the Control Arm referring to the enclosed TA User Manual

2. Mount the 400-mm (16") diameter Flange Plate onto the Core Holder "Quick-Chuck"

using the screws provided.

3. Slide the and Flange Assembly onto the UCAT-40 Motor Shaft "Quick-Chuck"

allowing for clearance to the Chassis and Motor Screws. Tighten the Allen screw to

secure the and Flange Assembly onto the Motor. "Quick-Chuck"

4. Set the UCAT-40 in place near the label entrance path of the printer.

5. CAUTION: AVOID ACCIDENTS. THE UCAT-40 WEIGHS APPROXIMATELY 13KG,

SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT.

6. The UCAT-40 is bi-directional. It can rewind labels in either direction.

7. Verify that the "DIRECTION" Switch on the UCAT-40 Control Panel is in the "OFF"

position.

8. Plug the Power Plug at the end of the wire on the AC Wall Transformer into the

UCAT-40 Power Input Jack. Plug the AC Transformer into an appropriate AC power

outlet.

9. The unit is now ready for use.

FOR YOUR SAFETY:

Switch oﬀ device before any manipulation.

POWER UNWINDING:

1. Place the "DIRECTION" Switch on the UCAT-40 Control Panel in the centre "OFF"

position.

2. Slide the roll of labels to be unwound on the Quick-Chuck.

3. Run the labels under the UCAT-40 Control Arm and into the printer.

4. Place the "DIRECTION" switch in the desired position to feed the labels into your

printer.

5. Place the "REWIND SLIT" Switch in the Rewind position and advance the –

"TORQUE" Control about 1/3 rotation from fully Counter-Clockwise as an initial

setting.

6. Start your printer and observe how the labels are being fed into the printer.

Adjust the "TORQUE" Control as needed to provide more or less unwind assistance. As

the printer uses the labels, the Control Arm will rise, causing the UCAT-40 to turn on and

feed more labels. As the UCAT-40 feeds more labels, the labels and the Control Arm will

drop down, turning oﬀ the UCAT-40 until more labels are needed as the Control Arm is

lifted again.

EXTERNAL HALT CONTROL:

An External Halt Control jack on the UCAT-3 is for use with external devices capable of

providing an open circuit halt command. A 3.5mm control cable is necessary for use (not

included).

With Pin 2 and Pin 3 of the External Halt Control circuit closed (connected together using

a 3.5mm dual circuit plug), the UCAT- will operate. When the External Circuit is opened, 3

the UCAT-3 will stop.

3.5mm “EXTERNAL HALT CONTROL” Stereo Plug (Dual Circuit Plug)

Contact CLOSED=RUN Contact OPEN=HALT

Pin 1 - No connection (NOT USED)

Pin 2 - Normally Closed (NC) contact

Pin 3 - Normally Closed (NC) contact return

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

2 31

Product specificaties

Merk:	Labelmate
Categorie:	Niet gecategoriseerd
Model:	UCAT-1-CHUCK
Kleur van het product:	Black, Grey
Soort:	Afwikkelaar
Aantal per verpakking:	1 stuk(s)
Merkcompatibiliteit:	Labelmate
Maximale label breedte:	270 mm
Core diameter:	100 mm
Apparaatcompatibiliteit:	Etiketprinter
Diameter rol:	300 mm