JETI SP 06 opto Handleiding

JETI Radiografisch bestuurbaar speelgoed SP 06 opto

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI SP 06 opto (1 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Function Switch SP 06

The switch SP 06 has been speciﬁcally designed for switching purposes of auxiliary functions such as

on board glow plug heating systems and miscellaneous lighting systems etc. in model airplanes, model ships

and model cars. The switched loads can be of ohmic, inductive or capacitive character. The switching instant

is signalled by ﬂash on of a LED.

By a shorting plug (jumper) the SP 06 switch can be adjusted to a „normal“

or „reverse“ condition. In the „reverse“ condition the switch reverses its

switching sense. If the switch with the jumper at „normal“ position was in the

„ON“ state, after replacing the jumper to the „reverse“ position with the same

control pulse and adjustment trimmer setting, it will change to the „OFF“

state.

By means of the built in trimmer the switching instant can be adjusted in

dependence on the incomming receiver control pulse.

Installation:

 apply only new high quality connectors, which must be soldered properly to the input and output cables

of the switch (look out for remnants of solder ﬂux on the connectors)

 connect the JR connector to the receiver output you want to use for controlling the switch (the controlling

part of the SP 06 switch obtains its current supply from the receiver)

 switch on the transmitter and receiver in order to set up the switching instant of the switch without load,

a LED indicates the ON anf OFF states of the switch (LED alight SP is ON) –

 by means of the trimmer and the respective control element of the transmitter you may adjust

the switching instant

 with the jumper position choose the ON or OFF function in accordance with the Tx control element

position

 connect the load to the switch output cables with the + - marks

 connect the switched voltage to the inputs with the marks + - on the ACCU side (watch the correct

polarity of the battery)

 check the switching function

Technical data:

SP 06

SP 06 OPTO

Switched input voltage

0 – 16 V

( 1 10 NiXX / 1 3 LiXX ) – –

3,5 16 V –

( 3 10 NiXX / 1 3 LiXX )– –

Resistance in conducting state

0,005 Ohm

Pulsating current (30 sec.)

10 A

Steady current

6 A

Supply voltage range of control

section

3,5 8,4 V –

3,5 8,4 V–

By trimmer adjustable switching range

1 ms to 2 ms

Operational temperature range of

switch

- 10 to +70 °C

-10 to +70 °C

Weight (without cables)

9 g ( 3g )

Dimensions

27 x 15 x 5 mm

For this product we grant a warranty of 24 months from the day of purchase under the assumption, that it has been

operated in conformity with these instructions at recommended voltages and that it has not been damaged mechanically.

Warranty and post warranty service is provided by the manufacturer.

JETI model s.r.o., Lomená 1530, 742 58 Příbor, Czech Republic, Phone:+420 556 810 708

www.jetimodel.cz

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	SP 06 opto
Kleur van het product:	Meerkleurig
Gewicht:	9 g
Breedte:	15 mm
Hoogte:	5 mm
Soort:	Radio-Controlled (RC) Model Parts
Aantal:	1
Impedantie:	0.005 Ohm
Spanning:	16 V
Lengte (max):	27 mm
Bedrijfstemperatuur (T-T):	-10 - 70 °C
Type product:	Schakelmodule
Stroom (max.):	10 A