JETI JEX-MU3 Handleiding

JETI Radiografisch bestuurbaar speelgoed JEX-MU3

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI JEX-MU3 (6 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

-1-

I NSTRUCTION MANUAL

OF THE SENSOR -3MU

1. INTRODUCTION ...................................................................................................................................... 2

2. CONNECTION .......................................................................................................................................... 2

2.1 C S ............................................................................................................................... 2 ONNECTION OF THE ENSOR

2.2 C -3 JETIBOX ................................................................................................................. 2 ONNECTING MU TO THE

2.3 C -3 ONNECTING THE MU TO A RECEIVERDUPLEX .............................................................................................. 2

2.4 C -3 DUPLEX E ................................................................................................... 3 ONNECTING MU TO A XPANDER

3. MENU NAVIGATION .............................................................................................................................. 3

3.1 ACTUAL VALUE ................................................................................................................................................ 3

3.2 MIN / MAX M – INIMUM AND AXIMUM ALUESM V ............................................................................................... 3

3.3 SETTING - C O ................................................................................................................. 4 ONFIGURATION PTIONS

3.4 ALARMS .............................................................................................................................................................. 4

3.5 SERVICE .............................................................................................................................................................. 4

4. TECHNICAL SPECIFICATION OF THE MU-3 .................................................................................. 5

5. FIRMWARE UPDATE ............................................................................................................................. 5

6. WARRANTY .............................................................................................................................................. 5

7. MENU DIAGRAM OF MU-3 ................................................................................................................... 6

Released by JETI model s.r.o 15.7.2011

INSTRUCTION MANUAL :MU-3

-2-

1. Introduction

The sensor MU-3 can be used for model on board monitoring of up to three voltages. With the aid of

the MU-3 sensor the historical course of particular voltages can be monitored (minimum and

maximum values) and the sensor may warn the user if set parameters are violated. Informations of

the sensor are transmitted by the Duplex System to the user.

The Duplex System utilizes the 2,4GHz band for communication, which not only transmits model

controlling data to the model but also receives useful model data back at the transmitter end. Data

collected during operation are transmitted in real time and the actual condition of measured values

can be evaluated on the JETIBOX LCD display.

2. Connection

2.1 Connection of the Sensor

It is possible to connect up to 3 independent voltage sources to the MU-3 sensor (see Fig.

below). Connect the voltages to the sensor input with correct polarities! After connection of the

voltages to the sensor inputs and connection of the sensor to its voltage supply, recognizing of

the active inputs will start and after approximately 2 seconds the sensor will be set according to

the number of recognized active inputs. The sensor recognizes the input as beeing active if the

connected voltage is higher than 0,1V. The connection and the following time calculation until

the setting moment is shown in the second line of the JETIBOX terminal. The sensor is

permanently set until the time it becomes switched oﬀ. When the sensor voltage supply is

switched on again there will be initiated a new recognizing process. If the sensor is deﬁnitely

set, any change of numbers of arbitrary active inputs will trigger an input error announcement.

The input error is notiﬁcated in the display as well as by an acoustic signal of the transmitter

module.

2.2 Connecting MU-3 to the JETIBOX

The triple-core cable of the MU-3 sensor with JR plug can be directly connected to the

JETIBOX (receptacle marked Pulse, + - ). Use the second input of the JETIBOX marked (+ -)

for the voltage supply, connect a voltage within a range of 3,5-8,4V. This conﬁguration oﬀers

no data transfer via radio link, therefore are data depicted on the JETIBOX LCD-screen only.

This wiring enables no generation of acoustic alert signals because the buzzer is part of the

transmitter module, which in this case is not connected. Alert signals are only shown on the

LCD-display.

2.3 Connecting the MU-3 to a DUPLEX receiver

Connect the triple core cable of the MU-3 module with its JR plug to the receptacle on the

backside of the DUPLEX receiver (marked Ext.). The MU-3 sensor obtains its current supply

INSTRUCTION MANUAL :MU-3

-3-

via the receiver. For the purpose of MU-3 sensor parameter adjustments connect the JETIBOX

to the transmitter module and switch on DUPLEX receiver and transmitter.

2.4 Connecting MU-3 to a DUPLEX Expander

Connect the triple core cable of the MU-3 module with its JR plug to one of the EXPANDER

inputs. The Expander oﬀers the possibility of connecting several telemetry sensors to one

receiver. The MU-3 sensor obtains in this case its current supply via the Expander and the

receiver.

3. Menu navigation

The JETIBOX terminal is used for parameter set-up and data readout. After connection to the MU-3

sensor the introductory display appears, showing in the ﬁrst line the sensor identiﬁcation. In the

second line indicates the actual voltage of inputs A,B,C. By long pushing down button R (right a fast )

deletion of all measured parameters can be trigger . Fast deletion is indicated in the ﬁrst line of the ed

display by asterix an „*“.

By pressing JETIBOX key D (arrow down) you will enter into the MU-3 sensor menu.

3.1 ACTUAL VALUE

MU-3 MENU: By pressing the 'D' (Down) button of the JETIBOX, we can Actual Value –

view the actual measured values.

A/B/C indicate actual voltages at all three inputs. –

3.2 MIN / MAX Minimum and Maximum Values –

MU-3 MENU: - by pressing key D (arrow down) you will select depiction of MIN / MAX

voltage extremes which occurred during measurements. Records of extremes are deleted

automatically or they can be deleted with the aid of the menu Automatic Setting - Erase Data.

deletion occurs if the MU-3 sensor has been just connected to the supply voltage and the

adjusted voltage, which has been set-up in the menu has been exceeded. Setting Trigger level,

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	JEX-MU3
Kleur van het product:	Zwart
Gewicht:	18 g
Breedte:	36 mm
Diepte:	20 mm
Hoogte:	5 mm
Soort:	Radio-Controlled (RC) Model Parts
Certificering:	CE
Correct gebruik:	Universeel
Merkcompatibiliteit:	JETI
Aantal:	1
Spanning:	3.5 - 8.4 V
Bedrijfstemperatuur (T-T):	-10 - 85 °C
Type product:	Sensor
Niet voor kinderen 0 - 3 jaar:	Ja
Werkingsstroom (@4,8 V):	8 mA