JETI J-MSW-200-MS Handleiding

JETI Radiografisch bestuurbaar speelgoed J-MSW-200-MS

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI J-MSW-200-MS (8 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

SER

ANUAL

ELECTRONIC

SWITCH

Main Switch

By JETI model s.r.o 25. 9. 2014

User Manual: Electronic switch Main Switch

-2-

1. Introduction

Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds

an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big

advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as

vibration resistance is concerned. Another advantage of the electronic switch is its ability to withstand an unlimited number

of switching cycles. Electronic switches have no moving parts like contacts which would be worn out during the switching

processes, therefore their longevity is extremely high. Moreover, they are not prone to spontaneous and unexpected false

tripping with known disastrous effects. Last but not least, electronic switches offer a much lower inherent transient

resistance in comparison to mechanical switches. The Main Switch prevents the connectors from sparking when

connecting the batteries, thus it can also replace Anti Spark plugs.

The Main Switch is shipped with a magnetic switch. The magnetic switch instructions can be found on the

manufacturer´s website. It is also possible to use the optional RC Switch instead of the magnetic switch.

The Main Switch is primarily designed for switching the main power supply of the RC models, but can also be used in

applications where switching a DC power supply is needed.

2. Connection

The power supply is connected to the Main Switch using two input wires with cross sections of 6 or 8mm

2. The output

voltage is available at two cables with cross sections of 6 or 8mm2. The output three-wire cable with the JR connector is

used for telemetry data transmission. The output three-pin connector is used to connect the supplied magnetic switch or

the RC Switch.

The Main Switch connects and disconnects the negative pole - , the + pole is always connected and is never

disconnected!

Fig. 1: Connection of input and output cables

Be sure to connect the power supply wires correctly; always connect the red cable to the + pole of the

accumulator, the black cable to the – pole of the accumulator. Pay attention when connecting outputs and inputs,

they must not be swapped. Failure to follow these requirements may result in irreversible damage to the Main

Switch!! Only connect batteries to the input IN and connect speed controllers, receivers, servos etc. to the output

OUT.

User Manual: Electronic switch Main Switch

-3-

Before switching on the electronic switch you should always connect the batteries first and only afterwards

switch on the system using the magnetic switch or the RC Switch. Follow this rule also for the switching off

procedure. Switch the system off first and disconnect the batteries only afterwards.

2.1 Connection of the Main Switch

The Main Switch measures the battery current and the voltage. If you do not need to get telemetry information from the

Main Switch, you do not have to connect the Ext. output. If you DO want to display then the telemetry the Main Switch Ext.

output must be connected to the Ext. Duplex receiver input. This also powers the measurement part of the Main Switch.

Fig. 2: Block diagram of the Main Switch

The ground (-) of the Main Switch Ext. is isolated. Do not connect the ground (-) of Magnetic switch / RC Switch to the

output ground of the Main Switch (-OUT).

2.2 Charging of the battery

The battery can be charged while connected to the Main Switch (be sure that the Main Switch is in the off state – the

green LED is off), but do not attempt to disconnect the battery while charging. The charging voltage is to be connected

directly to the battery (alternatively, to the battery through the switch input), but never connect charging voltage to the

switch output!! If it becomes necessary to disconnect the battery, disconnect the charging voltage first!! Failure to follow

these basic rules can destroy the Main Switch!!

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	J-MSW-200-MS
Kleur van het product:	Zwart
Gewicht:	140 g
Breedte:	80 mm
Diepte:	36 mm
Hoogte:	25 mm
Soort:	Radio-Controlled (RC) Model Parts
Certificering:	CE
Spanning:	9 - 51 V
Bedrijfstemperatuur (T-T):	-20 - 85 °C
Type product:	Schakelmodule
Stroom (max.):	200 A
Input voltage bereik:	9 - 51 V
Stroomsterkte zonder belading:	0.00011 A