JETI Hicopter 90A opto Handleiding

JETI Radiografisch bestuurbaar speelgoed Hicopter 90A opto

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI Hicopter 90A opto (1 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

HiCOPTER

The HiCOPTER product line of speed controllers are designed for controlling and regulating

brushless motors that are typically used for powering multicopters. Each speed controller is pre-set

from the factory with settings optimized for use with multi rotor aircraft stabilization systems.

HiCOPTER controllers accept a control signal with a frequency of up to 500Hz. This allows them to

accurately respond to any RPM change required by the control/stabilization unit of the multicopter.

The motor control signal is galvanically (optically) separated from the flight battery in all

HiCOPTER speed controllers. HiCOPTER speed controllers do not require or allow any programming

changes. The propeller brakes are already switched off, the cut-off voltage is pre-set to the lowest

possible level (depending on type) and the motor timing is set automatically by the speed controller. If

you need to change the direction of rotation, simply swap any two of the motor wires.

Install the HiCOPTER speed controller in accordance with the manual instructions for your specific

multicopter type.

Basic parameters of HiCOPTER speed controllers

Type Current

[A]

Input voltage

[V]

Dimensions

[mm]

Weight*

[g]

HiCOPTER 30A opto 30 5-25,2 65x26x9 35

HiCOPTER 40A opto 40 5-25,2 65x26x9 38

HiCOPTER 70A opto 70 5-25,2 70x26x11 45

HiCOPTER 90A opto 90 12-42 65x55x17 100

* weight with the cables

General Principles:

•please read these instructions carefully

•use only new connectors of good quality, which must be soldered properly to the controller

cables (look out for and remove any remaining flux on the plugs)

•flight battery wires can be extended to a maximum overall length of 20 cm

pay attention to the distance between all cables and the receiver antenna – the two should be

kept as far apart as possible

•only connect the flight batteries to the flight system shortly before the flight and then

disconnect them immediately after landing

•when the model is not in use, always disconnect all batteries from the flight system

•to prevent the possibility of reverse polarity connections to the controller or batteries use

different types of connectors for each type of connection

•do not connect the controller to current supplies other than appropriate battery pack (verify

that your batteries are the correct input voltage and can handle the current load)

•to prevent possible injuries by moving mechanical parts of the model (motor, gear box etc.)

always keep in mind that the motor may start unintentionally

•check the controller and receiver circuitry each time before switching the system on

•install the controllers in the model so that they receive air flow for cooling

Warranty:

We grant a warranty of 24 months from the date of purchase under the premise that the item has

been operated in accordance with these instructions within the specified voltage and currents and that

the controller does not show signs of mechanical damage. The warranty is void if the polarity of the

controller has been reversed or if the controller came in contact with different chemicals or water.

A controller can also be damaged due to following reasons: Use of unsuitable connectors, low

quality soldering joints (plugs), overly long cables between battery – controller – motor, a

demagnetizated motor, phase interruption (broken or damaged wire) between motor and controller

during operation.

Warranty service and any post warranty service is provided by the distributor or manufacturer.

JETI model s.r.o., Lomená 1530, 742 58 Příbor, Czech Republic www.jetimodel.cz

Product specificaties

Merk:	JETI
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	Hicopter 90A opto
Kleur van het product:	Geel
Gewicht:	100 g
Breedte:	65 mm
Diepte:	55 mm
Hoogte:	17 mm
Soort:	Radio-Controlled (RC) Model Parts
Correct gebruik:	Multikopter
Merkcompatibiliteit:	Alle merken
Aantal:	1
Spanning:	12 - 42 V
Compatibele batterij technologiën:	Lithium-Polymeer (LiPo)
Bedrijfstemperatuur (T-T):	-20 - 85 °C
Type product:	Snelheidsregelaar
Stroom (max.):	90 A
Maximaal aantal cellen compatibele batterij:	10
Compatibele batterijcellen minimumaantal:	4