HP Aruba Unified AP-515 Handleiding

HP Access point Aruba Unified AP-515

Lees hieronder de 📖 handleiding in het Nederlandse voor HP Aruba Unified AP-515 (15 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 124 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/15
Aruba 510 Series Campus Access Points
Installation Guide
Rev05 | December 2019 1
The Aruba 510 Series Campus Access Points (AP-514 and AP-515) are high-performance, multi-radio wireless
devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network
environments. These access points deliver high performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi
functionality with MIMO radios (2x2 in 2.4 GHz, 4x4 in 5 GHz), while also supporting legacy 802.11a/b/g/n/ac
wireless services.
Ethernet ports located on the back of this access points are used to connect the device to the wired networking
infrastructure and to provide (802.3at class 4) PoE power to the device.
In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio,
supporting a variety of use-cases and services, such as locationing and IoT.
A mount kit (sold separately) is needed to mount the AP. Make sure to purchase the correct mount kit for the
intended deployment of the AP.
Package Contents
Aruba 510 Series Campus Access Point (with a pre-installed mount bracket)
Hardware Overview
The following sections outline the hardware components of the 510 Series access points.
Figure 1 AP-515 Front View
The AP mount bracket attaches to a variety of mount kits (sold separately).
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible,
retain the carton, including
the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
2Aruba 510 Series Campus Access Points | Installation Guide
Figure 2 LEDs (AP-515 shown)
Figure 3 AP-514 Front View
External Antenna Connectors
The AP-514 access points are equipped with four external antenna connectors located on the front
corners of the access point (see
Figure 3
). Antenna ports A0 and A1 (co
rresponding with radio chains 0
and 1), are used for both radios and bands (RF signals are diplexed), while antenna ports A2 and A3
(corresponding with radio chains 2 and 3) are used for the 5 GHz radio only.
A0
A1
A2
A3
Aruba 510 Series Campus Access Points | Installation Guide 3
LEDs
The LED displays located on the front panel of the access point indicate the following functions:
System Status
The System Status LED indicates the operating condition of the access point, See Table 1.
Table 1 System Status LED
Radio Status
The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.
Table 2 Radio Status LEDs
!
!
!
!!
External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other
Aruba-certified technician, using manufacturer-approved antennas only.
The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the
regulatory limit set by the host country/domain.
Installers are required to record the antenna gain for this device in the system management software. A list of
approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf.
Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba
(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.
Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne
externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.
Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.
Une liste d'antennes approuvées peut être trouvée à http://www.arubanetworks.com/assets/og/OG_AP-
510Series.pdf.
Color/State Meaning
Off Device Powered off
Green- solid Device ready, fully functional, no network restrictions
Green- blinking 1
1. Blinking: one second on, one second off, 2 seconds cycle.
Device booting, not ready
Green- flashing 2
2. Flashing: mostly on, fraction of a second off, 2 seconds cycle.
Device ready, fully functional, either uplink negotiated in sub-optimal speed
(<1Gbps)
Amber- solid Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), no network restrictions
Amber- flashing Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), uplink negotiated in sub-optimal speed
Red System error condition - Immediate attention required
Color/State Meaning
Off Device powered off, or both radios disabled
Green- solid Both radios enabled in access mode


Product specificaties

Merk: HP
Categorie: Access point
Model: Aruba Unified AP-515

Heb je hulp nodig?

Als je hulp nodig hebt met HP Aruba Unified AP-515 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Access point HP

Handleiding Access point

Nieuwste handleidingen voor Access point