TP Link Festa F65-Outdoor Handleiding
TP Link
Access point
Festa F65-Outdoor
Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link Festa F65-Outdoor (2 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Overview
Package Contents
Panel Layout
Passive PoE Adapter
LED Status Indication
Solid green The device is initializing or working properly.
Flashing yellow System errors. RAM, Flash, Ethernet, WLAN or
rmware may be malfunctioning.
Slowly Flashing yellow, green Firmware update is in progress. Do not disconnect
or power o the device.
Quickly îž°ashing yellow, green The device is being reset to its factory default
settings.
Flashes green twice Initialization is completed.
SYS LED Explanation
Quickly îž°ashing green Locate the device.
Slowly îž°ashing green The device is in an isolated state.
1
RESET Grounding
Terminal
Ethernet
Port
Power LED PoE Port LAN Port
Waterproof Kit
Seal
(For Unshielded Cable) O-RingBracket
Seal
(For Shielded Cable)
Spiral Cover
Power Cord
Passive PoE Adapter
(Mounting Bracket Included)
Screw
(For Grounding
Wire Securing)
AP Installation Guide
Quick Installation Guide
Setup with videos
Visit https://www.tp-link.com/support/setup-video/ or scan the QR
code to search for the setup video of your product model.
Indo or/Outdoor Access Point
Plastic Wall Anchors Self-tapping ScrewsMounting Bracket
(For AP)
Pole Mounting Strap
Mounting Kit
* Accessories may vary by product.
Note: PoE Adapter may vary by model.
Lightning and ESD Protection
Before mounting the AP, consider Lightning and ESD Protection to ensure
safety.
Proper grounding is extremely important for outdoor devices. To reduce the
damage of potential lightning and ESD attacks, connect the grounding
terminal to grounding facilities using a proper grounding wire, which should
meet the local installation requirements. You need to secure the grounding
wire to the grounding terminal with the screw.
Hardware Installation
Mount the AP
The AP can be pole-mounted or wall-mounted. Follow the steps below
for the appropriate installation.
Option 1: Pole Mounting
Lead the end of the pole mounting strap
through the back of the AP.
Step 1:
Position the AP and wrap the pole
mounting strap around the pole.
Feed the end through the screw-block
and tighten the strap until the AP is
secure.
Step 2:
Option 2: Wall Mounting
Step 1:
Place the mounting bracket for AP in
the right position. Mark positions for
the screw holes .
Drill holes for the screws at the marked
positions.
Step 2:
Insert the plastic wall anchors into the
holes.
Align the mounting bracket to the
plastic wall anchors and drive the
self-tapping screws into the anchors
through the mounting bracket.
Step 3:
Align the mounting tabs on the back of
the AP with the slot of the mounting
bracket.
Push and slide the AP downward until
it locks into place.
3
2
Φ 7.6 mm (19/64 in)
AP
Grounded PoE Adapter
Ethernet Cable
Grounded 3-wire
Power Outlet
Indoor/Outdoor Access Point
Note: Festa F65-Outdoor is used as an example throughout the Guide. Images
may dier from your actual product.
©2024 TP-Link 7106511118 REV1.0.0
Quick Installation Guide
You can congure and manage Festa APs via the Festa Cloud-Based
Controller.
Option 1: Via Web Browser
Switch
Router / Gateway
Festa Cloud
Clients
AP AP AP AP
Option 2: Via Festa App
1. Make sure that your management device can access the internet.
2. Launch a web browser and enter https://festa.tplinkcloud.com in the
address bar. Log in with your TP-Link ID.
3. Click + Add Controller, then you will see you have successfully registered
for a Cloud-Based Controller and the controller has been added to the
controller list.
4. Click , and follow the step-by-step Set Up Now Config New Setup, click
instructions to complete the configuration wizard of the controller.
5. On the controller’s management page, go to Devices + Add , click
Devices, and follow the step-by-step instructions to adopt Festa devices.
Now you can configure and manage Festa devices on the controller.
https://festa.tplinkcloud.com
1. Download and install the Festa App from App Store or Google Play.
2. Launch the Festa App and log in with your TP-Link ID.
3. Tap + on the upper right corner, then you will see you have successfully
registered for a Cloud-Based Controller and the controller has been added
to the controller list.
4. Tap , tap Confirm Let’s Get Started, and follow the step-by-step
instructions to complete the conguration wizard of the controller.
5. On the controller’s management page, go to , click Devices + on the upper
right corner, and follow the step-by-step instructions to adopt Festa
devices.
Now you can configure and manage Festa devices via the Festa App.
Scan for Festa App Festa App
or
For technical support, the user guide and other information,
please visit https://www.tp-link.com/support/?type=smb, or simply
scan the QR code.
To ask questions, find answers, and communicate with TP-Link users
or engineers, please visit https://community.tp-link.com/business to
join TP-Link Community.
For detailed configurations, refer to the User Guide of the controller. The
guide can be found on the download center of our official website:
https://www.tp-link.com/support/download/?type=smb.
AT
EE
IS
NO SE SI SKPL PT RO UK(NI)
IT LI MT NLLT LU LV
EL FI FR HR HU IEES
BE BG DE DKCH CY CZ
UK
Attention: In EU member states, EFTA countries and Northern Ireland,
the operation in the frequency range 5150MHz-5350MHz is only
permitted indoors.
Attention: In Great Britain, the operation in the frequency range
5150MHz - 5350MHz is only permitted indoors.
For Festa Controller, go to the Devices page and select the desired AP
to specify the channel.
Software Conguration
4
Safety Information
• Keep the device away from re or hot environments. DO NOT immerse in
water or any other liquid.
• Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Do not use any other chargers than those recommended.
• Do not use damaged charger or USB cable to charge the device.
• Adapter shall be installed near the equipment and shall be easily
accessible.
• Adapter should be used indoors where the ambient temperature is lower
than or equal to 40 ℃.
• Plug the adapter into the wall outlets with earthing connection through the
power supply cord.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC,
2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at
https://www.tp-link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca/
Connect the Cable
Fit an Ethernet cable through the Spiral Cover Bracket O-Ring, , and ,
and connect the cable to the port.
Fit the and screw the to O-Ring Bracket to the head of the Bracket
the body of the device.
Note: Don’t warp the O-Ring.
Fit the Ethernet cable through the ’s slit with the Seal thicker side
towards the .Bracket Bracket, and plug the seal to the
Note: Choose the proper Seal according to the type and diameter of
the Ethernet cable.
Screw the Spiral Cover to the Bracket.
1
2
3
4
Spiral Cover
O-Ring
Bracket
1
Seal
3
4
2
Power On
The AP can be powered via the passive PoE adapter or a PSE device (such
as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited
Power Source (LPS) of IEC 62368-1.
Option 1: Via Passive PoE Adapter
Connect the PoE Adapter
Connect the AP to a Power over Ethernet (PoE) adapter as follows:
Mount the PoE Adapter (Optional)
Note: To ensure the passive PoE adapter is attached most securely, it is recommended
to install the adapter with the Ethernet port facing upward.
Step 1:
Remove the mounting bracket from the
passive PoE Adapter.
Drill two holes on the wall and insert the
plastic wall anchors into the holes. Secure
the mounting bracket to the wall. Make sure
the shoulders at the corners of the
mounting bracket are on the outside and
pointing upward.
Step 2:
Attach the passive PoE adapter to the
mounting bracket by sliding the adapter in
the direction of the arrows until it locks
into place.
Option 2: Via PoE Switch
Connect an Ethernet cable from the PoE switch to the Ethernet port.
Note: For PoE power supply specications, refer to the product label.
PoE Switch
PoE LAN
Ethernet cable
length up to 100 m
Product specificaties
| Merk: | TP Link |
| Categorie: | Access point |
| Model: | Festa F65-Outdoor |
Heb je hulp nodig?
Als je hulp nodig hebt met TP Link Festa F65-Outdoor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Access point TP Link
11 December 2024
3 December 2024
15 November 2024
3 Oktober 2024
4 Mei 2024
25 April 2024
26 Maart 2024
26 Maart 2024
26 Maart 2024
14 November 2023
Handleiding Access point
- Access point Bosch
- Access point HP
- Access point Huawei
- Access point Asus
- Access point Honeywell
- Access point Airlive
- Access point Allied Telesis
- Access point Allnet
- Access point AVM
- Access point Buffalo
- Access point D-Link
- Access point Dell
- Access point Devolo
- Access point Digitus
- Access point Draytek
- Access point Edimax
- Access point Eminent
- Access point Engenius
- Access point EQ-3
- Access point Grandstream
- Access point Hercules
- Access point INCA
- Access point Interlogix
- Access point Lancom
- Access point LevelOne
- Access point Linksys
- Access point Media-tech
- Access point Mikrotik
- Access point Mojo
- Access point Netgear
- Access point Netis
- Access point Renkforce
- Access point Sitecom
- Access point SMC
- Access point Tenda
- Access point Trendnet
- Access point Zebra
- Access point ZyXEL
- Access point Macally
- Access point Steren
- Access point Ubiquiti Networks
- Access point Techly
- Access point Cisco
- Access point 3Com
- Access point Amped Wireless
- Access point Comtrend
- Access point CradlePoint
- Access point Juniper
- Access point Planet
- Access point Intellinet
- Access point Silex
- Access point Lindy
- Access point Black Box
- Access point Fortinet
- Access point DataVideo
- Access point Totolink
- Access point Dahua Technology
- Access point Mercusys
- Access point Aruba
- Access point EQ3
- Access point Homematic IP
- Access point Hawking Technologies
- Access point AMX
- Access point Moog
- Access point Crestron
- Access point StarTech.com
- Access point WatchGuard
- Access point LigoWave
- Access point Advantech
- Access point Moxa
- Access point Kingston
- Access point Vimar
- Access point Aerohive
- Access point Bountiful
- Access point V7
- Access point NUVO
- Access point Cudy
- Access point IP-COM
- Access point Syscom
- Access point Meru
- Access point Cambium Networks
- Access point Ruckus Wireless
- Access point Bintec-elmeg
- Access point Mach Power
- Access point ICC
- Access point Insteon
- Access point Brocade
- Access point Premiertek
- Access point Extreme Networks
- Access point Atlantis Land
- Access point FlyingVoice
- Access point Luxul
Nieuwste handleidingen voor Access point
8 December 2024
8 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024