Hobart MG1532 Handleiding

Hobart Mengpaneel MG1532

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobart MG1532 (8 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
701 S. R ID G E AVENUE
TROY, OHIO 45373
937 332-3000
www.hobartcorp.com FORM 34389 Rev. E (January 2024)
MG1532 & MG2032 MIXER-GRINDERS
MODEL
MG1532 ML-134099 7.5 hp Grind Motor + 1 hp Mix Motor
MG2032 ML-134104 7.5 hp Grind Motor + 1 hp Mix Motor
MG2032 ML-134105 7.5 hp Grind Motor + 1 hp Mix Motor w/ Side Feed
MG2032 ML-141244 7.5 hp Grind Motor + 1 hp Mix Motor w/ Side Feed
MIXER GRINDER-
– 2 –
© HOBART, 2024
MODEL MG2032 MIXER-GRINDER
MODEL MG1532 MIXER-GRINDER
– 3 –
Installation, Operation, and Care of
MG1532 & MG2032 Mixer-Grinders
SAVE THESE INSTRUCTIONS
GENERAL
The MG1532 & MG2032 Mixer-Grinders are designed to use a #32(42/46) size knife and plate (knives
and plates are available at extra cost but not included with grinder). Do not use a plate with hole size
smaller than 3/ ".32
The MG1532 & MG2032 Mixer-Grinder are equipped with a 7 1/ HP2 Grind Motor and a 1 HP Mix Motor.
On all models, the worm rotates at 216 RPM and the mix arm rotates at 23 RPM.
The inclined hopper permits lower, easier loading while the tilted worm provides a convenient output height.
Releasing the latch handle allows the hopper guard (lid) to open easily — torsion springs counterbalance
the lid's weight.
The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding
end by pulling pieces of meat through the large upper opening of the cylinder (Fig. 1).
The MG1532 & MG2032 Mixer-Grinders may be ordered
with any of the following options and/or accessories:
• Pneumatic foot switch accessory (can be easily
added at any time).
• The hopper side-feed inlet can be ordered (and factory
installed) for the right side of the MG2032 hopper only
to allow product from a companion îš¿rst cut grinder
to feed directly into the hopper. An adapter ring for
the îš¿rst-cut grinder is an available accessory.
The MG1532 hopper can hold up to 150 pounds of fresh
meat. The MG2032 hopper can hold up to 200 pounds of
fresh meat. The MG1532 & MG2032 Mixer-Grinders can
grind at a rate of 55 to 60 pounds of fresh boneless beef per minute, îš¿rst or second cut through a 1/ " 8
plate. Pork can be ground îš¿rst cut through a 3/4" breaker plate and second cut through a 3/16" plate at 60 to
65 pounds per minute. Up to 60 pounds of frozen meat per batch can be ground from ake or stick form
when tempered to 26°F or higher and rst grind is through a 3/ " or larger plate. 8
For best results, we recommend using equipment in a cold room and/or using cold product. This will help
reduce the fatting of meat at the grinder head and on the mixing arm and worm.
Fig. 1

Product specificaties

Merk: Hobart
Categorie: Mengpaneel
Model: MG1532

Heb je hulp nodig?

Als je hulp nodig hebt met Hobart MG1532 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Mengpaneel Hobart

Hobart

Hobart MG1532 Handleiding

27 Februari 2025

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel

Ecler

Ecler eHMA60 Handleiding

10 Februari 2025
Alfatron

Alfatron ALF-VM41 Handleiding

5 Februari 2025
Alfatron

Alfatron ALF-VMix41 Handleiding

7 Januari 2025
Hanseatic

Hanseatic HHBL1000SD Handleiding

6 Januari 2025
Bosch

Bosch Plena PLE-1ME120 Handleiding

27 December 2024
Bosch

Bosch Plena PLE-1ME60 Handleiding

27 December 2024
Bosch

Bosch Plena PLE-1ME240 Handleiding

27 December 2024
DNA

DNA CM4-DSP Handleiding

24 December 2024
DNA

DNA Mix 4U Handleiding

24 December 2024
Ashly

Ashly AquaTouch 7 Handleiding

15 December 2024