Hobart 4822 Handleiding

Hobart Vleesmolen 4822

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Hobart 4822 (12 pagina's) in de categorie Vleesmolen. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobar tcorp.com F-35109 Rev. A (April 2014)
MODEL 4822 CHOPPER
ML-136125
ML-136126
– 2 –
Β© HOBART, 2014
Installation, Operation and Care of
MODEL 4822 CHOPPER
SAVE THESE INSTRUCTIONS
GENERAL
The 4822 Chopper uses a 11/2 horsepower motor. It will grind 16 lbs. per minute, fi rst cutting, through a
1/ " plate.8
The 4822 Chopper, with funnel-shaped cylinder, will grind 20 to 22 lbs. per minute, fi rst cutting, through
a 1/ " plate.8
Fig. 1
– 3 –
INSTALLATION
UNPACKING
Remove the carton from around the machine. Remove the four bolts holding the machine to the skid.
Unpack the chopper cylinder assembly.
Immediately after unpacking the chopper, check for possible shipping damage. If this machine is found to
be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure that it agrees with the specifi cations on the
machine data plate.
The four leg assemblies (Fig. 1) are removed and packed in a separate carton for shipment. Unpack and
assemble these legs by screwing them into the four tapped holes of the frame. The rubber feet on these
legs cushion the machine. Under normal operation, the machine need not be bolted down.
ELECTRICAL CONNECTIONS
The electrical cord on this machine is equipped with a grounding- type plug which
must be connected to a properly grounded receptacle. If the receptacle is not the proper grounding
type, contact an electrician. Do not remove the grounding prong from the plug.
Choppers with three phase motors should be connected so that the hub drive runs counterclockwise
facing the cylinder assembly.
A check must be made to verify correct direction of rotation. Energize machine momentarily by turning
switch ON then OFF.
If rotation is incorrect, disconnect plug from electrical outlet, disassemble the plug and interchange any
two power leads (not the green ground lead). Then reassemble the plug and recheck.

Product specificaties

Merk: Hobart
Categorie: Vleesmolen
Model: 4822

Heb je hulp nodig?

Als je hulp nodig hebt met Hobart 4822 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Vleesmolen Hobart

Hobart

Hobart 4146 Handleiding

9 Augustus 2023
Hobart

Hobart MG2032 Handleiding

9 Augustus 2023
Hobart

Hobart 4246 Handleiding

9 Augustus 2023
Hobart

Hobart 4822 Handleiding

9 Augustus 2023
Hobart

Hobart 4732A Handleiding

9 Augustus 2023
Hobart

Hobart 4812 Handleiding

9 Augustus 2023
Hobart

Hobart 4732 Handleiding

9 Augustus 2023

Handleiding Vleesmolen

Nieuwste handleidingen voor Vleesmolen

Zelmer

Zelmer ZMM4045B Handleiding

14 November 2024
Philips

Philips HR7995 Handleiding

11 November 2024
Royal Catering

Royal Catering RCMT-350W Handleiding

5 November 2024
Royal Catering

Royal Catering RCFW-220EXPERT Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RC-MMA16 Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RCFW-220PRO Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RC-MMA28 Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RCFW 540PRO Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RCMM-2000W Handleiding

14 Oktober 2024
Royal Catering

Royal Catering RCFW 140-850ECO Handleiding

14 Oktober 2024