Hobart 4732A Handleiding
Hobart
Vleesmolen
4732A
Lees hieronder de 📖 handleiding in het Nederlandse voor Hobart 4732A (8 pagina's) in de categorie Vleesmolen. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
4732 & 4732A CHOPPERS
MODEL
4732 ML-18887 (PAINTED, NON-REMOVABLE PAN)
ML-19282 (SST, NON-REMOVABLE PAN)
4732A ML-19689 (PAINTED, REMOVABLE PAN)
ML-19690 (SST, REMOVABLE PAN)
MODEL 4732 CHOPPER
FORM 34747 Rev. A (March 2012)
– 2 –
Installation, Operation and Care of
4732 & 4732A Choppers
SAVE THESE INSTRUCTIONS
GENERAL
The 4732 and 4732A Choppers are equipped with a 3 HP motor that rotates the worm at 151 RPM. The
4732 and 4732A are designed to use a #32 size knife and plate. Knives and plates, available at extra cost,
are not included with the chopper.
The stainless steel feed pan on the 4732 is not removable and must be cleaned in place. Model 4732A
has a removable stainless steel feed pan and an interlock that requires the feed pan to be in place before
the machine can be turned on. On both models, a cast aluminum guard is permanently mounted to the
front and sides of the feed pan. Dimensions on the feed pan are 34" long x 21" wide x 5" deep. The motor
and switch housing is available in painted steel or stainless steel. The table models use 5 3/8" high legs
that provide 8" clearance between the table and the lowest point on the adjusting ring. Leg sets of other
heights (18" or 21") are available to convert the 4732 or 4732A into a fl oor model. Sausage stuffers for
hog or sheep casings are available accessories.
The chopper can grind 35 to 40 pounds of boneless beef per minute, fi rst cut, through a 1/8" plate. The
second cut grind rate is 25 to 30 pounds per minute through a 1/8" plate. Frozen meat must be tempered
to 24°F or higher before grinding and can be in either fl ake or stick form.
INSTALLATION
UNPACKING
Immediately after unpacking, check for possible shipping damage. If the chopper is found to be damaged,
save the packaging material and contact the carrier within 15 days of delivery.
Remove the carton from around the machine. Remove the four bolts holding the machine to the skid.
Unpack the feed stomper.
Prior to installation, verify that the electrical service agrees with the specifi cations on the machine data plate.
Use the spanner wrench to loosen the adjusting ring. Unscrew and remove the adjusting ring using both
hands. Remove and discard the retaining washer and rubber pad used at the front of the worm where the
knife and plate are to be installed.
The chopper must be thoroughly cleaned and sanitized after installation and before operation. Refer to
CLEANING (page 7).
© HOBART, 2012
– 3 –
LEGS (FIGS. 1 & 2)
The four leg assemblies are packed in a separate
carton for shipment. The standard legs (53/8" high)
allow the rim of the feed pan on the table model to
be 27" above the table surface. These legs have
neoprene feet and require assembly. To assemble
53/8" high legs: Slide the Leg Stud through the Leg End
Cap and the Leg; then thread the Leg Stud into the
base of the machine (Fig. 2). Do not overtighten; the
legs need only be hand-tight. Thread the Neoprene
Foot into the Leg Stud (Fig. 2).
Floor model choppers are equipped with optional 18" or 21" legs. Each Leg is one piece and threads into
the base of the machine at the four corners. These Legs can be adjusted by threading the Feet in or out
as necessary (Fig. 2) to level and stabilize the chopper.
Fig. 1
Fig. 2
PL-56170
LEG (18" or 21")
LEG
LEG END CAP
LEG STUD
NEOPRENE FOOT FOOT
34"
INSIDE
5"
8-1/2"
4-3/8"
33-5/16"
DIM "B"
DIM "C"
DIM "A"
15-1/4"
4-1/16"
21"
INSIDE
17-3/8" 1-3/8"
20-1/8"
12-1/2"
1-5/16"
MACHINE HEIGHT FOR LEG OPTIONS
LEGS DIM "A" DIM "B" DIM "C" MODEL
5-3/8"
STD 10-3/4" 5-3/8" 4732
4732A
18"
OPT 23-3/8" 18" 4732
4732A
21"
OPT 26-3/8" 21" 4732
4732A
00-088182
ACCESS FOR
ELECTRICAL
POWER CONNECTION
WARNING
ELECTRICAL & GROUNDING CONNECTIONS MUST COMPLY WITH
THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL
CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
(1-1/16 DIA HOLE)
FOR 3/4" TRADE SIZE CONDUIT
ELECTRICAL CONNECTION HOLE
ON/OFF SWITCH MAY BE
MOUNTED FOR RIGH HAND
OR LEFT HAND OPERATION
27"
27-3/8"
39-5/8"
40"
42-5/8"
43"
Product specificaties
| Merk: | Hobart |
| Categorie: | Vleesmolen |
| Model: | 4732A |
Heb je hulp nodig?
Als je hulp nodig hebt met Hobart 4732A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Vleesmolen Hobart
9 Augustus 2023
9 Augustus 2023
9 Augustus 2023
9 Augustus 2023
9 Augustus 2023
9 Augustus 2023
9 Augustus 2023
Handleiding Vleesmolen
- Vleesmolen Braun
- Vleesmolen Bosch
- Vleesmolen Philips
- Vleesmolen Panasonic
- Vleesmolen BEKO
- Vleesmolen Kenwood
- Vleesmolen Krups
- Vleesmolen Tefal
- Vleesmolen Ade
- Vleesmolen Adler
- Vleesmolen Afk
- Vleesmolen Amica
- Vleesmolen Ariete
- Vleesmolen Beem
- Vleesmolen Bestron
- Vleesmolen Buffalo
- Vleesmolen Duronic
- Vleesmolen ETA
- Vleesmolen Eurochef
- Vleesmolen Fritel
- Vleesmolen Gastroback
- Vleesmolen Gorenje
- Vleesmolen H.Koenig
- Vleesmolen Hyundai
- Vleesmolen Klarstein
- Vleesmolen Korona
- Vleesmolen Livoo
- Vleesmolen Maestro
- Vleesmolen Magic Chef
- Vleesmolen Magimix
- Vleesmolen Manta
- Vleesmolen Maxwell
- Vleesmolen Melissa
- Vleesmolen Mesko
- Vleesmolen Moulinex
- Vleesmolen MPM
- Vleesmolen Princess
- Vleesmolen ProfiCook
- Vleesmolen Redmond
- Vleesmolen Rotel
- Vleesmolen Saturn
- Vleesmolen Sencor
- Vleesmolen Silvercrest
- Vleesmolen Steba
- Vleesmolen Taurus
- Vleesmolen Ufesa
- Vleesmolen United Office
- Vleesmolen Vitek
- Vleesmolen Zelmer
- Vleesmolen Jata
- Vleesmolen Caso
- Vleesmolen Concept
- Vleesmolen Cuisinart
- Vleesmolen OBH Nordica
- Vleesmolen Profilo
- Vleesmolen Scarlett
- Vleesmolen Sinbo
- Vleesmolen Ardes
- Vleesmolen Eldom
- Vleesmolen Lümme
- Vleesmolen Prime3
- Vleesmolen Royal Catering
- Vleesmolen Weston
- Vleesmolen Nesco
- Vleesmolen RGV
- Vleesmolen Reber
- Vleesmolen Avantco
- Vleesmolen N8WERK
- Vleesmolen Fama
- Vleesmolen Globe
- Vleesmolen LERAN
- Vleesmolen Zeegma
- Vleesmolen WestBend
- Vleesmolen Pro-Cut
- Vleesmolen Browin
Nieuwste handleidingen voor Vleesmolen
14 November 2024
11 November 2024
5 November 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024