Hikvision DS-KIS901-P Handleiding
Hikvision
Intercomsysteem
DS-KIS901-P
Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-KIS901-P (16 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/16
Diagram References
Regulatory Informaon
FCC Informaon
Please take aenon that changes or modificaon not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or television recepon,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Condions
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operaon.
● All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire
prevenon regulaons and other related regulaons in your local region.
● Please use the power adapter, which is provided by normal company. The power consumpon cannot
be less than the required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire
hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable,
and then please contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center. Never
aempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused
by unauthorized repair or maintenance.)
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm
radiaon. Avoid the equipment installaon on vibraons surface or places subject to shock (ignorance can
cause equipment damage).
● Do not place the device in extremely hot (refer to the specificaon of the device for the detailed
operang temperature), cold, dusty or damp locaons, and do not expose it to high electromagnec
radiaon.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is
forbidden (ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which
is not a malfuncon however), and affecng the endurance of sensor at the same me.
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover,
because the acidic sweat of the fingers may erode the surface coang of the device cover.
● Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not use
alkaline detergents.
● Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you need to
return the device to the factory with the original wrapper. Transportaon without the original wrapper may
result in damage on the device and lead to addional costs.
● Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used baeries according to the instrucons provided by the baery
manufacturer.
Product Informaon
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the RE Direcve
2014/53/EU, the EMC Direcve 2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS Direcve
2011/65/EU
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or dispose of it at designated
collecon points. For more informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as
unsorted municipal waste in the European Union. See the product documentaon for specific
baery informaon. The baery is marked with this symbol, which may include leering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your
supplier or to a designated collecon point. For more informaon see:www.recyclethis.info
Safety Instrucon
Cauons
Warnings ● Tous les éléments électroniques doivent respecter à la lere la réglementaon locale sur la sécurité des installaons électriques, sur
la prévenon des incendies et des réglementaons connexes en vigueur.
● Ulisez un adaptateur fourni par une entreprise agréée. La consommaon électrique ne doit pas être inférieure à la valeur exigée.
● Ne branchez pas plusieurs appareils sur un même adaptateur ; toute surcharge de l'adaptateur pouvant entraîner sa surchauffe ou
provoquer un incendie.
● Veillez à bien déconnecter la source d’alimentaon avant de câbler, installer ou démonter l’appareil.
● Lors de l'installaon au mur ou au plafond, assurez-vous que l'appareil est bien fixé.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et débranchez le câble
d'alimentaon, puis contactez le SAV.
● Si le produit ne fonconne pas correctement, contactez votre revendeur ou le SAV le plus proche. Vous ne devez en aucun cas essayer
de démonter le produit vous-même. (Nous déclinons toute responsabilité en cas de problèmes découlant d'une intervenon ou d'une
réparaon effectuée sans autorisaon.)
● Évitez de faire tomber l’appareil, de le heurter et de l'exposer à des rayonnements électromagnéques de forte intensité. Évitez
d'installer l'équipement sur des surfaces vibrantes ou à des emplacements subissant des chocs fréquents (au risque de l'endommager).
● N'installez pas l’appareil à un emplacement trop chaud ou trop froid (reportez-vous à la spécificaon de l’appareil pour connaître la
température de fonconnement précise), poussiéreux ou humide. Ne l'exposez pas non plus à des rayonnements électromagnéques
élevés.
● Le capot de l’appareil pour installaon intérieure ne doit pas être exposé à la pluie, ni à l'humidité.
● Il est formellement interdit d'exposer l'équipement directement au soleil, à un environnement mal venlé ou à une source de chaleur
telle qu'une chaudière ou un radiateur (au risque de provoquer un incendie).
● N'orientez pas l’appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des traînées risquent de se
former (ce qui ne constue toutefois pas un dysfonconnement) et la résistance du capteur peut également être affectée.
● Ulisez le gant fourni pour ouvrir le capot du dôme et évitez tout contact direct avec celui-ci, l'acidité de la sudaon des doigts
pouvant éroder le revêtement du capot de l’appareil.
● Ulisez un chiffon doux et sec pour neoyer les surfaces intérieures et extérieures du capot de l’appareil. N'ulisez pas de détergents
alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l’appareil à l'usine dans son
emballage d'origine. Si l’appareil est transporté hors de son emballage d'origine, il risque d'être abîmé, entraînant des frais
supplémentaires.
● Une mauvaise ulisaon de la baerie ou un remplacement erroné peut entraîner un risque d'explosion. Ne la remplacez que par une
baerie idenque ou de type équivalent. Meez les baeries usagées au rebut conformément aux instrucons du fabricant.
Consignes de sécurité
Précauons
Averssements :
Appearance
Installaon
Before you begin:
Wall Mounng
Acvate Indoor Staon
1
3
Geng Started
4
Wiring
2
Display Screen Microphone Unlock Buon
1 324
5 6 7
1. Tools that you need to prepare for installaon: Make sure the device in the package
is in good condion and all the assembly parts are included.
2. The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
3. Make sure all the related equipment is power-off during the installaon.
4. Check the product specificaon for the installaon environment.
1. Fix the wall mounng plate to the wall with 2 supplied screws.
2. IPut the indoor staon on the holder of the wall mounng plate.
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon and tap Next.
a. Choose Indoor Staon Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor staon are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the door staon in the list to link.
b. Tap the sengs icon to pop up the Network Sengs page.
c. Edit the network parameters of the door staon manually or enable DHCP to get
the network parameters automacally.
d. Oponal: Enable Synchronize Language to synchronize the Language of door
staon with indoor staon.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
Debugging Port Network Interface
SD Card Slot
Loudspeaker
8Alarm Terminal
Note:
The debugging port is used for debugging only.
The Unlock key is valid only when does the indoor staon speak with the door staon or open the
live view of the door staon.
Refer to Video Intercom Indoor Staon Configuraon Guide (scan the QR code) for details.
Refer to Video Intercom Indoor Staon Operaon Guide (scan the QR code) for details.
You are required to acvate the device first by seng a strong password for it before
you can use the device.
1
Quick Configuraon
2
DS-KIS901-P
DS-KH8350-WTE1
Video Intercom Network Indoor Staon
Video Intercom Network Bundle
E N G L I S H
UD18305B
There are 20 pins in the terminal on the rear panel of the indoor staon 2 RS-485
pins, 2 power pins, 2 GND pins, 2 alarm output pins, 8 alarm input pins, and 2
reserved pins.
It supports wall mounng. There are two installaon modes.
The wall mounng plate is are required to install the indoor staon onto the wall.
The dimension of wall mounng plate is shown.
©2020 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware embodied in the Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright protecon. Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to
this manual. This manual cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior wrien permission
of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applicaons for the same by Hikvision
and/or its affiliates. Other trademarks menoned in this manual are the properes of their respecve owners. No right of license is given to use such
trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS
IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG
OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO
ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE
PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Data Protecon
During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy
by design principles. For example, for device with facial recognion features, biometrics data is stored in your device with encrypon method; for fingerprint
device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protecon laws and regulaons,
including without limitaon, conducng security controls to safeguard personal data, such as, implemenng reasonable administrave and physical security
controls, conduct periodic reviews and assessments of the effecveness of your security controls.
12
3 3
1
23 4
7
8
5 6
RS-485+
RS-485-
Blue
Green
Red DC 12V IN
GND
ALARM_OUT2
ALARM_IN1
ALARM_IN2
ALARM_IN3
ALARM_IN4
ALARM_IN5
ALARM_IN6
ALARM_IN7
ALARM_IN8
Black
Black
Black
Red
Red
ALARM_OUT1
Yellow
Yellow
White
White
White
White
White
White
White
White
GND
GND
Res
Res
Security
Control
Device
Reserved
Reserved
Power
Input
Screw
Screw
Indoor Station Mounting Plate Wall
Diagram References
Acvaon
4
Wiring Descripon
3
Installaon
Installaon Environment
1
1. Create a password and confirm the password.
2. Tap Acvate to acvate the device.
Note: For other acvaon methods, see the device user manual.
Indoor and outdoor installaon are supported. If installing the device indoors, the
device should be at least 2 meters away from the light, and at least 3 meters away
from the window or the door. If installing the device outdoors, you should apply
Silicone sealant among the cable wiring area to keep the raindrop from entering.
Note:The addional force shall be equal to three mes the weight of the equipment
but not less than 50N. The equipment and its associated mounng means shall
remain secure during the installaon. Aer the installaon, the equipment,
including any associated mounng plate, shall not be damaged.
Power on and wire the network cable aer installaon. You should acvate the device
before the first login.
If the device is not acvated yet, it will enter the Acvate Device page aer powering
on.
Wall Mounng
1. Make sure the gang box is installed on the wall.
2. Use 2 supplied screws (SC-K1M4×6-SUS) to secure the base plate on the gang box.
Route the cables through the cable hole of the mounng plate, and connect to the
corresponding external devices’ cables.
Use another 4 supplied screws (KA4×22-SUS)to secure the mounng plate on the base
plate.
Note: Apply Silicone sealant among the cable wiring area to keep the raindrop from entering.
3. Align the device with the mounng plate and hang the terminal on the mounng plate.
4. Use 1 supplied screw (SC-KM3X6-H2-SUS) to secure the device and the mounng plate.
5. Apply Silicone sealant among the joints between the device rear panel and the wall
(except the lower side) to keep the raindrop from entering.
Note: You can also install the device on the wall or other places without the gang box.
For details, refer to the User Manual.
DS-K1T341 Series
Face Recognion Terminal E N G L I S H 2
4
3.2
1
3.1
2
3
7
4
5
6
11
12
13
14
10
9
8
1
12
3 4 5
Direct
Sunlight Direct Sunlight
through Window
Backlight Indirect Sunlight
through Window
Close to Light
Appearance
2
Loudspeaker MicroUSB Interface Camera
1 324
5 6 7
Card Presenng AreaMicrophone
IR Light
White Light 8IR Light
9 10 11Fingerprint ModuleScreen Network Interface
12 13Wiring Terminal Tamper Debugging Port14
Note: The debugging port is used for debugging only.
Connect
Network
Interface of
Device
Connect
Network
Cable
Notes:
When connecng door magnec sensor and exit buon, the device and the RS-485
card reader should use the common ground connecon.
The Wiegand terminal here is a Wiegand input terminal. You should set the face
recognion terminal’s Wiegand direcon to “Input”. If you should connect to an access
controller, you should set the Wiegand direcon to “Output”. For details, see Seng
Wiegand Parameters in Communicaon Sengs in the user manual.
The suggested external power supply for door lock is 12 V, 1A.
The suggested external power supply for Wiegand card reader is 12 V, 1 A.
For wiring the fire module, see the user manual.
If the interface for network connecon is too large, you can use the supplied cable as
shown below.
Device Wiring
3.1
Device Wiring with Secure Door Control Unit
3.2
Note: The secure door control unit should connect to an external power supply
separately. The suggested external power supply is 12 V, 0.5 A.
STRONG PASSWORD RECOMMENDED–
We highly recommend you create a strong password of your own choosing (using a
minimum of 8 characters, including upper case leers, lower case leers, numbers,
and special characters) in order to increase the security of your product. And we
recommend you reset your password regularly, especially in the high security system,
reseng the password monthly or weekly can beer protect your product.
Use only power supplies listed in the user instrucons:
Make sure the power supply is used indoors, and the working temperature is
between 0 and 40 °C.
83.2 mm
172.5 mm
This sticker means“Hot parts! Burned fingers when handling the parts. Wait
one-half hour after switching off before handling parts.”It is to indicate that
the marked item can be hot and should not be touched without taking care.
For device with this sticker, this device is intended for installation in a restricted
access location, access can only be gained by service persons or by users who
have been instructed about the reasons for the restrictions applied to the
location and about any precautions that shall be taken.
Model
Manufacture
Standard
ADS - 62 F G 2 202S - 1 1 4EPG
Sh zh H Een en onor lectron Co t ic .,L d
PG
MSA - C2000IC 21 . -0 24 - DE MOSO TP ech .,L d DEnology Co t P
ADS - 62 F G 2 202S - 1 1 4EP B
Sh zh H Een en onor lectron Co t ic .,L d
P B
ADS - 62 F G 2 202S - 1 1 4EPC PC U/E
Sh zh H Een en onor lectron Co t ic .,L d
PC U
ADS - 62 F G 2 202S - 1 1 4EPI 0- 1 Sh zh H E en en onor lectron Co t PI ic .,L d
ADS - 62 F G 2 202S - 1 1 4EP R B
Sh zh H Een en onor lectron Co t ic .,L d
P R B
RS-485
Wiegand
Door Lock
Network Interface
Power Input
GND
GND
GND
GND
BTN
12V External
Power Supply
Wiegand
Card Reader
Group B
Group D
B1
B2
B3
C1
C2
C3
D6
D7
D1
D2
D3
D4
D5
(NC)
(COM)
(NO)
Eletric Dropbolt
Power Supply
Eletric Strike Door Contact
Exit Button
White/Black
White/Purple
White/Yellow
White/Red
Yellow/Green
Yellow/Gray
Yellow/Black
Black
Red/Black
Black
Yellow
Green
White
Blue
Red
NO
COM
NC
NO
COM
NC
Sensor Input
Power Input
SENSOR
BUTTON
B1
B2
B3
B4
Green/Brown Door Contact
Black
Green/Black
Black
Lock Output
NC C1
C2
C3
COM
(NC)
Power
(NO)
(COM)
White/Purple
White/Black
White/Red
Exit Button
Face Recognition Terminal
NO
COM
NC
NO
COM
NC
Electric
Dropbolt
Electric
Strike
Secure Door Control Unit
Red
Black
Exit Button
RS-485 B1
B2
B3 Red/Black
Yellow
Blue
Secure Door
Control Unit
Wiring Terminal
Activate
Acvate Device
Enter Password
Comfirm Password
Comfirm password.
Enter 8 to 16 characters.
Enter 8 to 16 characters.
Product specificaties
| Merk: | Hikvision |
| Categorie: | Intercomsysteem |
| Model: | DS-KIS901-P |
Heb je hulp nodig?
Als je hulp nodig hebt met Hikvision DS-KIS901-P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Intercomsysteem Hikvision
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
7 Augustus 2024
30 December 2023
4 Augustus 2023
Handleiding Intercomsysteem
- Intercomsysteem Philips
- Intercomsysteem Panasonic
- Intercomsysteem Bticino
- Intercomsysteem Abus
- Intercomsysteem Acti
- Intercomsysteem Alcatel
- Intercomsysteem Alecto
- Intercomsysteem Axis
- Intercomsysteem Byron
- Intercomsysteem DIO
- Intercomsysteem Elro
- Intercomsysteem Estom
- Intercomsysteem Foscam
- Intercomsysteem Gira
- Intercomsysteem HQ
- Intercomsysteem Konig
- Intercomsysteem Marmitek
- Intercomsysteem Midland
- Intercomsysteem Monacor
- Intercomsysteem Siedle
- Intercomsysteem Silvercrest
- Intercomsysteem Smartwares
- Intercomsysteem Somfy
- Intercomsysteem Sygonix
- Intercomsysteem Toa
- Intercomsysteem Viking
- Intercomsysteem Becken
- Intercomsysteem Schwaiger
- Intercomsysteem Steren
- Intercomsysteem DoorBird
- Intercomsysteem EMOS
- Intercomsysteem Avidsen
- Intercomsysteem Comelit
- Intercomsysteem Extel
- Intercomsysteem M-e
- Intercomsysteem NuTone
- Intercomsysteem TCS
- Intercomsysteem Chacon
- Intercomsysteem Swann
- Intercomsysteem Valcom
- Intercomsysteem Fibaro
- Intercomsysteem GEV
- Intercomsysteem Planet
- Intercomsysteem Chamberlain
- Intercomsysteem DataVideo
- Intercomsysteem Dahua Technology
- Intercomsysteem Busch-Jaeger
- Intercomsysteem Russound
- Intercomsysteem Fanvil
- Intercomsysteem Aiphone
- Intercomsysteem Crestron
- Intercomsysteem ORNO
- Intercomsysteem Sonifex
- Intercomsysteem RTS
- Intercomsysteem Nortek
- Intercomsysteem Vimar
- Intercomsysteem ZKTeco
- Intercomsysteem Akuvox
- Intercomsysteem Bitron
- Intercomsysteem Hollyland
- Intercomsysteem Elcom
- Intercomsysteem Hanwha
- Intercomsysteem Leviton
- Intercomsysteem EtiamPro
- Intercomsysteem Pentatech
- Intercomsysteem Ritto
- Intercomsysteem Arenti
- Intercomsysteem Syscom
- Intercomsysteem Pentatron
- Intercomsysteem Vibell
- Intercomsysteem CyberData Systems
- Intercomsysteem COMMAX
- Intercomsysteem Bintec-elmeg
- Intercomsysteem Eartec
- Intercomsysteem Gewiss
- Intercomsysteem Seco-Larm
- Intercomsysteem Tador
- Intercomsysteem WHD
- Intercomsysteem Mobotix
- Intercomsysteem FlyingVoice
- Intercomsysteem Toucan
Nieuwste handleidingen voor Intercomsysteem
16 December 2024
15 December 2024
2 December 2024
2 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024