Hikvision DS-KIS604-P Handleiding

Hikvision Intercomsysteem DS-KIS604-P

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-KIS604-P (7 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

DS-KIS604-P

Video Intercom Network Bundle UD17076B-B

Screen Microphone

2Debugging Port

3Network Interface

Loudspeaker

5TF Card Slot

6Alarm Terminal

7Reserved

Note:

The appearance of the device varies according to diﬀerent models. Refers to the actual device for detailed

informaon.

The debugging port is used for debugging only.

Terminal and Wiring

There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485 pins, 5

reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.

Installaon

It supports wall mounng. There are two installaon modes.

ENGLISH

Diagram References

Appearance

Installaon Accessory Descripon

The wall mounng plate and juncon box are required to install the indoor staon onto

the wall.

The dimension of juncon box should be 75 mm (width) 75 mm (length) 50 mm

× ×

(depth). The dimension of wall mounng plate is shown.

Wall Mounng with juncon Box

Make sure the device in the package is in good condion and all the assembly parts

are included.

The power supply the indoor staon supports is 12 VDC. Please make sure your

power supply matches your indoor staon.

Make sure all related equipments are power-oﬀ during the installaon.

Check the product speciﬁcaon for the installaon environment.

Before You Start

1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm

(length) × 50 mm (depth).

2. Insert the juncon box to the hole chiseled on the wall.

3. Fix the wall mounng plate to the juncon box with 2 screws.

4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate

hooks into the slots on the rear panel of the indoor staon, during which the lock catch

will be locked automacally.

Geng Started

You are required to acvate the device ﬁrst by sengs a strong password before you

can use the device.

Acvate Indoor Staon

Quick Conﬁguraon

Refers to Video Intercom Network Indoor Staon Conﬁguraon Guide (Scan the QR code) for details.

Refers to Video Intercom Network Indoor Staon Operaon Guide (Scan the QR code) for details.

6789

Power Terminal

Note: There are 20 pins in the terminal on the rear panel of the DS-KH6320-TE1: 11 reserved pins, 8 alarm

input pins, and 1 GND pin. Please refer to the speciﬁc model.

Wall Mounng without juncon Box

1. Insert 2 expansion tubes into the wall.

2. Fix the wall mounng plate to the juncon box with 2 screws.

3. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate

hooks into the slots on the rear panel of the indoor staon, during which the lock catch

will be locked automacally.

Rear Panel (without Interface)

Lock Catch Lock Catch

Hook Hook

Screw Wall Mounng Plate Wall

Rear Panel (without Interface)

Lock Catch Lock Catch

Hook Hook

Screw Wall Mounng Plate Juncon Box Wall

Scan the QR code to get the

Operaon Guide for detailed

informaon.

Scan the QR code to get the

Conﬁguraon Guide for detailed

informaon.

RS-485

Reserved

Relay Output

Alarm

Input

Device

RS-485+

RS-485-

RES

NO2

NO1

COM1

COM2

AIN7

AIN6

AIN5

AIN4

AIN3

AIN2

AIN1

GND

AIN8

Red

Blue

Green

Yellow

White

Black

Red

Black

White

122

Unit:mm

100

64.85

1. Choose Language and tap Next.

2. Set network parameters and tap Next.

- Edit Local IP, Subnet Mask and Gateway parameters.

- Enable DHCP, the device will get network parameters automacally.

3. Conﬁgure the indoor staon parameters.

- .Select Indoor Staon and tap Next to link main door staon.

a. Edit Floor and Room No.

b. Create and conﬁrm SIP register password.

Note: If you want to add the indoor staon to the door staon, the SIP password of the indoor staon

should be the same as the registraon password of the door staon.

c. Tap Advanced Sengs to edit Community No, Building No. and Unit No.

d. Oponal: Enable Indoor Staon Sengs and select the indoor staon to link.

- . Select Indoor Extension and tap Next to link indoor staon.

a. Edit No., Room Name.

b. Create and conﬁrm SIP register password.

4. Linked related devices and tap Next. If the device and the indoor staon are in the

same LAN, the device will be displayed in the list. Tap the device or enter the serial No.

to link.

a. Tap the sengs icon to pop up the Network Sengs page.

b. Edit the network parameters of the door staon manually or enable DHCP to get

the network parameters automacally.

e. Tap OK to save the sengs.

5. Tap Finish to save the sengs.

DS-KH6320-WTE1

Network Indoor Staon

1. Power on the device. It will enter the acvaon page automacally.

2. Create a password and conﬁrm it.

3. Tap OK to acvate the indoor staon.

4. Oponal: Bind email address. You can reset the acvaon/admin password vial the

email ﬁ you forget your password.

DS-KV8113-WME1

Video Intercom Villa Door Staon

Diagram References

ENGLISH 1

89 10

GND

NC2

485+

COM2

NO2

AIN1

AIN2

AlARM IN

AIN3

AIN4

LAN

485-

GND

12VDC

RS-485

DOOR2

GND

NC1

COM1

NO1

DOOR1 POWER

Microphone 2Indicator 3Loudspeaker

4Buon

Card Reading Area

6IR Light

7Micro SD Card Slot(Reserved) & Debugging Port

Note: The debugging port is used for debugging only.

Terminal and Wiring

Installaon Accessory

Appearance

Surface Mounng without Protecve Shield

1. Sck the mounng template on the wall. Drill screw holes according to the mounng

template. Remove the template from the wall.

2. Secure the mounng plate on the wall with 4 supplied screws according to the screw holes.

3. Secure the device on the mounng plate with 4 supplied set screws.

4. Fix the cover onto the device with the screw.

Make sure all related equipments are power-oﬀ during the installaon.

Tools that you need to prepare for installaon: Drill (ø2.846) and gradienter.

Purchase the protecve shield before installaon.

Before You Start

Conﬁguraon via Web

You are required to acvate the device ﬁrst by sengs a strong password before you

can use the device.

Acvate Device via Web1

Access to the Device by Web Browsers2

1. In the browser address bar, enter the IP address of the device, and press the Enter

key to enter the login page.

2. Enter the user name and password and click Login.

Refers to Video Intercom Villa Door Staon User Manual (scan the QR code) for details.

Network Interface

1Camera

Terminals

Indicator Descripon Unlock: Green Call: Orange Communicate: White

NC: Door Lock Relay Output (NC)

NO: Door Lock Relay Output (NO)

COM: Common Interface

AIN1: For the access of Door Contact

AIN3: For the access of Exit Buon

AIN2&AIN4: Reserved

485-: RS-485 Interface (Reserved)

485+: RS-485 Interface (Reserved)

12 VDC IN: Power Supply Input

GND: Grounding

Mounng Template 21 Mounng Plate

Note: The dimension of the mounng plate is 174 mm × 83.66 mm × 18 mm.

Installaon

Note: Video intercom villa door staon supports surface mounng.

Default parameters of door staon are as follows:

Default IP Address: 192.0.0.65.

Default Port No.:8000.

Default User Name: admin

1. Power on the device, and connect the device to the network.

2. Enter the IP address into the address bar of the web browser, and click Enter to enter

the acvaon page.

Note: The computer and the device should belongs to the same subnet.

3. Create and enter a password into the password ﬁeld.

4. Conﬁrm the password.

5. Click OK to acvate the device.

Note: When the device is not acvated, the basic operaon and remote conﬁguraon of device cannot be

performed.

Communicate with Indoor Staon3

1. Click Sengs -> Intercom -> Press Buon to Call to enter the sengs page.

2. Set the parameters.

- Edit call No. for every buon.

- Check Call Management Center to set the buon calling center.

Note: If you check Call Management Center and set the call No. as well, call management center has

higher privilege than call No.

3. Press buon to call indoor staon.

Issue Card4

1. Click Sengs -> Access Control and Elevator Control to enter the sengs page.

2. Click Issue Card. Present the card on the card reading area.

3. When issuing ﬁnished, the windows pop up on the sengs page.

Note:

Only M card supported, and M card with non-standard shape is recommended.

1 1

Up to 10000 cards can be issued and managed by V series door staon. A voice prompt (No more cards

can be issued.) can be heard when the issued card amount exceeds the upper limit.

Unlock Door

Aer issuing cards, you can unlock the door by presenng the issued cards.

LAN: Network Interface

Flush Mounng without Protecve Shield

1. Sck the mounng template on the wall. Drill the hole according to the mounng template.

Remove the template from the wall. The suggested size of hole is 175 mm × 84 mm × 19 mm.

2. Install the gang box into the hole with 4 screws.

3. Insert the device to the gang box. Secure the device with 4 supplied screws.

4. Fix the cover onto the device with the screw.

Cover Screws Villa Door Station Mounting Plate Mounting Template Wall Cover Screws Villa Door Station Gang Box Wall

Surface Mounng without Protecve Shield Flush Mounng without Protecve Shield

18mm

83.66mm

174mm

The recommended distance from the ground level is

1.40m and it is adjustable depends on the height of body.

Hole1 Hole1

Hole2

Hole3

10 202 311 5

Références du schéma

FRANÇAIS

Video Intercom Network Bundle

Verweise auf Schaubilder

DEUTSCH

Referencias del diagrama

ESPAÑOL

Riferimento schemi

ITALIANO

Referências do diagrama

PORTUGUÊS

Schemareferenes

NEDERLANDS

Popis obrázků

ČEŠTINA

Diagramoversigt

DANSK

Bildschirm Mikrofon Debug-Anschluss

Netzwerkanschluss Lautsprecher TF-Kartensteckplatz

Alarm-Anschlussklemme

Hinweis:

● Das Erscheinungsbild des Geräts variiert je nach Modell. Für detaillierte Informaonen siehe das

tatsächliche Produkt.

● Der Debugging-Anschluss wird nur für die Fehlersuche verwendet.

Anschlüsse und Verkabelung

Hinweis: Beschreibungen der Anschlussklemmen und der Verdrahtung ﬁnden Sie in der Abbildung und im

Benutzerhandbuch.

Installaon

Bevor Sie beginnen

●A chten Sie darauf, dass sich das Gerät in der Verpackung in gutem Zustand beﬁndet und

alle Montageteile enthalten sind.

●A chten Sie darauf, dass alle relevanten Geräte während der Montage ausgeschaltet sind.

●Ü berprüfen Sie die Produktspeziﬁkaon für die Installaonsumgebung.

Hinweis: Einzelheiten zur Installaon ﬁnden Sie in der Abbildung und im Benutzerhandbuch.

Erste Schrie

Gerät akvieren

Bevor Sie das Gerät benutzen können, müssen Sie zunächst ein sicheres Passwort

festlegen, um das Gerät zu akvieren.

Akvieren Sie das Gerät lokal oder aus der Ferne über die iVMS-4200-Clientsoware.

Schnellkonﬁguraon

Folgen Sie den Auﬀorderungen in den entsprechenden Menüs.

Auau

AnschlussklemmeReserviert

Pantalla Micrófono Puerto de depuración

Interfaz de red Altavoz Ranura para tarjeta TF

Terminal de alarma

Nota:

● La apariencia del disposivo varía en función del modelo. Consulte el disposivo en concreto para más

información.

● El puerto de depuración solo sirve para depurar.

Terminal y cableado

Nota: para las descripciones de los terminales y del cableado, consulte la ﬁgura y el manual de usuario.

Instalación

Antes de comenzar

●A segúrese de que el disposivo incluido esté en buenas condiciones y se incluyan todas

las piezas de ensamblaje.

●A segúrese de que todos los equipos relacionados estén apagados durante la instalación.

●C onsulte las especiﬁcaciones del producto al realizar la instalación.

Nota: Nota: consulte las ilustraciones y el manual de usuario para conocer el procedimiento de instalación.

Primeros pasos

Acvar disposivo

Antes de poder ulizar el disposivo es necesario acvarlo estableciendo una contraseña

segura.

Acve el disposivo de forma local o a distancia mediante el soware de cliente iVMS-4200.

Conﬁguración rápida

Siga los avisos de las interfaces correspondientes.

Apariencia

Borne de alimentaciónReservado

Schermo Microfono Porta di debugging

Interfaccia di rete Altoparlante Slot per scheda TF

Terminale di allarme

Nota:

● L'aspeo del disposivo varia in base al modello. Per informazioni deagliate, fare riferimento al

disposivo eﬀevo.

● La porta si usa solo per avità di debugging.

Terminale e cablaggio

Nota: per la descrizione del cablaggio e dei terminali, fare riferimento alla ﬁgura e al Manuale dell'utente.

Installazione

Prima di iniziare

●V eriﬁcare il disposivo contenuto nella confezione sia in buone condizioni e che tu gli

elemen di assemblaggio siano presen.

●V eriﬁcare che durante l'installazione tue apparecchiature correlate siano spente.

●C ontrollare che le speciﬁche del prodoo corrispondano a quelle dell'ambiente di

installazione.

Nota: Per l'installazione, fare riferimento alla ﬁgura e al Manuale dell'utente.

Operazioni preliminari

Ava disposivo

Prima di ulizzare il disposivo è necessario avarlo impostando una password sicura.

Avare il disposivo localmente o da remoto tramite il soware client iVMS-4200.

Conﬁgurazione rapida

Seguire le indicazioni sulle interfacce corrisponden.

Aspeo

Terminale di alimentazioneRiservato

Écran Microphone Port de débogage

Interface réseau Haut-parleur Fente de carte TF

Terminal d’alarme

Remarque :

● L’aspect de l’appareil varie en foncon des diﬀérents modèles. Reportez-vous à l’appareil réel pour des

informaons détaillées.

● Le port de débogage est réservé uniquement à l’usage prévu.

Borne et câblage

Remarque : pour la descripon des bornes et du câblage, reportez-vous à la ﬁgure et au manuel de l’ulisateur.

Installaon

Avant de commencer

●A ssurez-vous que l’appareil dans son emballage est en bonne condion et que toutes les

pièces de montage sont incluses.

●A ssurez-vous que tous les équipements connexes sont hors tension pendant

l’installaon.

●V ériﬁez que les spéciﬁcaons du produit sont adéquates à l’environnement

d’installaon.

Remarque : pour l’installaon, reportez-vous à la ﬁgure et au manuel d’ulisaon.

Premiers pas

Acver un appareil

Vous devrez d’abord acver l’appareil en déﬁnissant un mot de passe fort avant de

pouvoir l’uliser.

Acvez l’appareil localement ou à distance via le logiciel client iVMS-4200.

Conﬁguraon rapide

Suivez les instrucons sur les interfaces correspondantes.

Apparence

Borne d’alimentaonRéservé

Ecrã Microfone Porta de depuração

Interface de rede Alfalante Ranhura Para Cartão TF

Terminal de alarme

Nota:

● O aspeto do disposivo varia consoante o modelo. Consulte a documentação especíﬁca do disposivo

para obter informações detalhadas.

● A Porta de depuração desna-se apenas para ﬁns de depuração.

Terminal e cablagem

Nota: Para as descrições de cablagem e dos terminais, consulte a ﬁgura e o manual do ulizador.

Instalação

Antes de começar

●C erﬁque-se de que o disposivo na embalagem se encontra em boas condições e de

que todas as peças de montagem estão incluídas.

●C erﬁque-se de que, durante a instalação, todo o equipamento relacionado se encontra

desligado.

●V eriﬁque a especiﬁcação do produto para o ambiente de instalação.

Nota: Para a instalação, consulte a ﬁgura e o Manual do Ulizador.

Introdução

Avar disposivo

Antes de poder ulizar o disposivo, é necessário avá-lo primeiro, deﬁnindo uma

palavra-passe segura.

Ave localmente o disposivo ou remotamente através do soware de cliente iVMS-4200.

Conﬁguração rápida

Siga as mensagens apresentadas nas interfaces correspondentes.

Aspeto

Terminal de alimentaçãoReservado

Scherm Microfoon Poort voor debuggen

Netwerkinterface Luidspreker Sleuf TF-kaart

Alarmaansluing

Opmerking:

● Het uiterlijk van het apparaat varieert per model. Raadpleeg het daadwerkelijke apparaat voor meer

informae.

● De foutopsporingspoort wordt alleen gebruikt voor foutopsporing.

Aansluingen en bedrading

Opmerking: Raadpleeg voor een beschrijving van de aansluing en bedrading de aeelding en de

gebruikershandleiding.

Installae

Voordat u begint

●Z org dat het verpakte apparaat zich in goede staat bevindt en er geen onderdelen

ontbreken.

●Z org dat alle bijbehorende apparatuur jdens de installae is uitgeschakeld.

●C ontroleer de productspeciﬁcae op geschiktheid in de installaeomgeving.

Opmerking: Raadpleeg voor installae de aeeldingen en de gebruikershandleiding.

Aan de slag

Apparaat acveren

U dient het apparaat voor gebruik eerst te acveren door er een sterk wachtwoord voor

in te stellen.

Schakel het apparaat ter plekke of op afstand in m.b.v. iVMS-4200-clientsoware.

Snelle conﬁgurae

Volg de aanwijzingen op desbetreﬀende interfaces.

Uiterlijk

Aansluing voedingGereserveerd

Obrazovka Mikrofon Ladicí port

Síťové rozhraní Reproduktor Slot pro kartu TF

Svorka alarmu

Poznámka:

● Vzhled zařízení se u různých modelů liší. Podrobné informace naleznete v dokumentaci příslušného

zařízení.

● Ladicí port se používá pouze k ladění.

Svorka a zapojení

Poznámka: Popis svorky a zapojení naleznete na obrázku a v návodu k použi.

Montáž

Dříve než začnete

●U jistěte se, zda je zařízení v balení v dobrém stavu a zda jsou přítomny všechny

dodávané součás.

●U jistěte se, že veškerá příslušná zařízení jsou během instalace vypnutá.

●Z kontrolujte technické údaje produktu týkající se prostředí instalace.

Poznámka: Při instalaci se řiďte obrázkem a uživatelskou příručkou.

Začínáme

Akvace zařízení

Před použim zařízení je musíte akvovat nastavením silného hesla.

Zařízení akvujte v místě nebo vzdáleně prostřednictvím klientského sowaru iVMS-4200.

Rychlá konﬁgurace

Postupujte podle výzev v příslušném rozhraní.

Vzhled

Napájecí terminálVyhrazeno

Skærm Mikrofon Port l fejlﬁnding

Netværkssk Højaler TF-kortplads

Alarmterminal

Bemærk:

● Enhedens udseende varierer i henhold l forskellige modeller. Se den fakske enhed for nærmere

oplysninger.

● Fejlﬁndingsporten bruges kun l fejlﬁnding.

Terminal og ledningsføring

Bemærk: Find beskrivelse af terminaler og ledningsføring i ﬁguren og brugervejledningen.

Installaon

Før du starter

●K ontrollér, at enheden i pakken er i god lstand, og at alle dele l samling medfølger.

●K ontrollér, at alt lknyet udstyr er slukket under installaonen.

●K ontrollér produktspeciﬁkaonerne for installaonsmiljøet.

Bemærk: Find oplysninger om installaonen i ﬁguren og brugervejledningen.

Kom godt i gang

Akvér enhed

Du skal først akvere enheden ved at indslle en stærk adgangskode, før du kan anvende

enheden.

Akvér enheden lokalt eller via ernadgang via iVMS-4200-klientsoware.

Hurg konﬁguraon

Følg talevejledningen på de lsvarende skærme.

Beskrivelse

StrømterminalReserveret

DS-KIS604-P

DS-KH6320-WTE1