Fredenstein Bento 6 DS Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Fredenstein Bento 6 DS (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Bento 6 DS
Module Carrier
Operating Manual
Fredenstein Bento 6 DS Module Carrier
The Fredenstein Bento 6 DS is the most advanced module carrier for six Fredenstein Series 600
modules or API-500 compatible plug-in cards in 3U 19 inch rack format. The Bento 6 DS features
several important upgrades compared with third party products:
The color LCD Display and a rotary encoder: To set routing and other parameters with non-volatile
storage. In addition, if certain Fredenstein modules are used, like F600A, F601A, F602, F603A/B,
and the F607, all operating parameters of theses modules are displayed as well.
Universal power supply: accepting mains voltages from 90V AC to 240V AC, 50 to 60 Hz.
Increased output currents: 3A or 500 mA per slot and +48V DC 0.3A
Monitoring of output voltages and currents.
Auxiliary Audio Inputs and Outputs
Built-in Audio Routing: Modules can be daisy-chained by simply using the menu driven user
interface on the LCD.
Built-in compatibility switches for non-conforming modules.
Compressor buss linking: Compressor modules can be linked simply using the menu driven user
interface on the LCD as well.
Multilayer back-plane: Increased signal integrity and lower noise floor.
Ground-lift switching: In case of ground loops, the audio ground and the protective ground can be
disconnected. Please use only if absolutely necessary.
Installation:
Electrical Safety Warnings:
Do not open the enclosure, hazardous voltages are present inside!
There are no user serviceable parts inside.
Always disconnect the mains cord before installing or removing modules!
If you need to replace the mains fuse, make sure the replacement has the same
rating ( 3 AT).
Please disconnect the mains from your Bento 6 DS before installing or removing modules. Make
sure each installed module is well seated in the receiving connector and the module is secured by
fasten the two mounting screws (size: M3).
Front View:
Fredenstein Bento 6 DS Manual V1.0 Jan 17, 2017 Page 1
Fredenstein Bento 6 DS Module Carrier
If certain non-Fredenstein modules are used, which bridge several pins on the connector and
connected the contacts on the top and button side, the double switches, located directly besides the
slot connectors, can both be turned off (lower position) to avoid interference between the module
and the digital interconnect. For Fredenstein modules, both need to be in the ON (upper) position.
Operation:
After installation of the modules, connect the mains cord to the Bento 6 DS IEC socket located on
the back-panel and than connect the mains cable to a grounded outlet. Now turn the Bento 6 DS on
by operating the I/O switch (also part of the IEC socket on the back). The following screen will be
displayed indicating the status and power-supply voltages.
Now the Bento 6 DS is ready and will display any request from
certain Fredenstein modules.
To enter the setup menu, please push the wheel and the setup menu
will appear.
Configuration of audio linking
Configuration of compressor buss linking
Various Setting
Save Configuration
Recall Configuration
Turning the wheel left or right to scroll from one menu point to the next, the highlighted menu point
will get selected when the wheel is pushed. Selecting Exit and pushing the wheel will show the
Status screen again.
Fredenstein Bento 6 DS Manual V1.0 Jan 17, 2017 Page 2


Product specificaties

Merk: Fredenstein
Categorie: Niet gecategoriseerd
Model: Bento 6 DS

Heb je hulp nodig?

Als je hulp nodig hebt met Fredenstein Bento 6 DS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Fredenstein

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd