Fredenstein Bento 8 Handleiding

Fredenstein Niet gecategoriseerd Bento 8

Lees hieronder de 📖 handleiding in het Nederlandse voor Fredenstein Bento 8 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
Bento 8
Pure Analog
Module Carrier
Operating Manual
Fredenstein Bento 8 Pure Analog Module Carrier
The Fredenstein Bento 8 features a complete linear power supply consisting of a mains transformer
and linear regulators. This topology yields the cleanest power to your modules.
Usually linear power supplies can't deliver high output currents, but Bento 8 outputs +/-16V DC 2A
and +48V DC 0.25A, 500mA per slot, that's ample power for the most demanding 500 series
modules!
Another drawback of linear supplies is that they are prone to introduce hum magnetically from the
mains transformer directly into input and output transformer inside modules, especially when
plugged into the slot closest to the supply. Bento 8 incorporates extensive magnetic shielding of the
mains transformer to eliminate induced hum.
The Bento 8 is constructed of the highest grade components:
1.5mm (59 mil) Steel Chassis, Toroidal mains transformer with two built-in thermal fuses, all
electrolytic capacitors are made by Nichicon and are rated for 105 (221 ), etc.℃ ℉
Built-in Audio Routing:
Modules can be daisy-chained by simply flipping switches on the back-panel.
Compressor buss linking:
Compressor modules can be linked by engaging switches on the back-panel as well.
Ground-lift switch:
In case of ground loops, the audio ground and the protective ground can be disconnected. Please use
only if absolutely necessary.
Installation:
Please make sure the unit has the correct mains voltage rating for your country.
(See label on the rear)
Electrical Safety Warnings:
Do not open the enclosure, hazardous voltages are present inside!
There are no user serviceable parts inside.
Always disconnect the mains cord before installing or removing modules!
If you need to replace the mains fuse, make sure the replacement has the same
rating (3AT 250V, slow blow).
Make sure each installed module is well seated in the receiving connector and
the module is secured by fastening the two mounting screws.
Fredenstein Bento 8 Manual V1.1 Dec 26, 2019 Page 1
Fredenstein Bento 8 Pure Analog Module Carrier
Front View:
Operation:
After installation of the modules connect the mains cord to the Bento 8 IEC socket located on the
back-panel and than connect the mains cable to a grounded outlet. Now turn the Bento 8 on by
operating the I/O switch (also part of the IEC socket on the back). The three LEDs on the front-
panel will come on and the Bento 8 is ready for use.
In case you want to route the audio signal, for example, from a mic-pre in slot 1 to a EQ in slot 2
and then to a compressor in slot 3, turn the switches located in the lower part of the back-panel
between the slot 1 and 2 and slot 2 and 3 in the link position. (Please be aware that this disables the
slot 2 and the slot 3 input XLR connectors). Slot 1 input will be the microphone input and the slot 3
output will be the audio output of the complete chain.
If you are using multiple compressors which make use of the compressor link buss (Pin 6), you can
link two adjacent slots by putting the buss switch in the I position. You have the flexibility to have
four buss segments for operating four Stereo compressor setups by engaging buss switches between
the slots 1 & 2, 3 & 4, 5 & 6, and 7 & 8 or any other combination including a global buss if you
engage all buss switches (surround 5.1 configuration). If you are using different types of
compressors, you must keep them on separate segments of the buss.
In case of severe ground loops you might engage the ground-lift to alleviate such problems. But it is
always recommended to resolve the grounding problems at their source and keep the ground-lift
switch disengaged (OFF position).
Fredenstein Bento 8 Manual V1.1 Dec 26, 2019 Page 2

Product specificaties

Merk: Fredenstein
Categorie: Niet gecategoriseerd
Model: Bento 8

Heb je hulp nodig?

Als je hulp nodig hebt met Fredenstein Bento 8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Fredenstein

Fredenstein

Fredenstein Artistic Comp SE Handleiding

7 December 2023
Fredenstein

Fredenstein Bento 2 Pure Analog Handleiding

7 December 2023
Fredenstein

Fredenstein Artistic MIC-PRE SE Handleiding

16 November 2023
Fredenstein

Fredenstein Artistic Compressor Plus Handleiding

15 November 2023
Fredenstein

Fredenstein Bento 8 Handleiding

9 Mei 2023
Fredenstein

Fredenstein F200 Handleiding

8 Mei 2023
Fredenstein

Fredenstein Bento 2 Handleiding

8 Mei 2023
Fredenstein

Fredenstein Artistic Mic-Pre Handleiding

30 April 2023
Fredenstein

Fredenstein Bento 6 DS Handleiding

25 April 2023
Fredenstein

Fredenstein F607 Handleiding

14 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

True

True UNITE Touchscreen Console Handleiding

23 December 2024
Alpine

Alpine TME-M780EM Handleiding

23 December 2024
ARNOLD Lichttechnik

ARNOLD Lichttechnik MCU 400 D Handleiding

23 December 2024
HK Audio

HK Audio TB-45NQ Handleiding

23 December 2024
HK Audio

HK Audio TB-45N Handleiding

23 December 2024
D-Link

D-Link DFE-680TX Handleiding

23 December 2024
D-Link

D-Link DGE-550T Handleiding

23 December 2024
D-Link

D-Link DGE-560SX Handleiding

23 December 2024
D-Link

D-Link DGE-510T Handleiding

23 December 2024
Mercusys

Mercusys MS116GS Handleiding

23 December 2024