Fe Powertools FE 30 kernboormachine Handleiding

Fe Powertools Boormachine FE 30 kernboormachine

Lees hieronder de 📖 handleiding in het Nederlandse voor Fe Powertools FE 30 kernboormachine (6 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
2 Manual magnetic drilling machines
1. Table of contents
2. Table of contents
3. Safety procedures
4. Technical overview
5. Operating manual
5.1 Hole cutter selection
5.2 How to mount tools or adapters in a Weldon arbor
5.3 Drilling with hole cutters
5.4 Drilling with twist drills
5.5 Tapping / threading
5.6 Speed and torque setting
6. Tips and tricks
7. Maintenance
8. CE Declaration of Conformity
9. Warranty
3 Manual magnetic drilling machines
1. Safety procedures
When using magnetic drilling machines please follow the general safety instructions for electric
power tools.
Please read the manual Use eye protection use ear protection
use safety helmet use safety gloves wear appropriate clothing
disconnect before opening use safety chain Warning for electrical shock
dangerous environment don’t use in wet places pacemaker warning
TIP: Do not use your magnetic drill on the same structure when ARC welding is in progress. D.C.
current will earth back through the magnet and cause irreparable damage.
WARNING: This appliance must be earthed.
1. Always secure the machine with the supplied safety chain before starting to operate, this to protect the user in case of power
failure or breaking loose of the magnet whilst in use.
2. Always wear safety goggles, gloves and ear plugs.
3. Disconnect from the power source when changing cutters or working on the machine.
4. Always ensure cutter retaining screws are secure – they sometimes vibrate loose in use.
5. Regularly clean the work area and machine., remove swarf and dirt, paying particular attention to the underside of the magnet.
6. With a gloved hand, after switching off the power, remove any swarf which might have gathered around the cutter and arbor
before proceeding to the next hole.
7. Remove tie, rings, watches and any loose adornments which might entangle with the rotating parts of the machine.
8. Should the cutter get stuck in the workpiece, stop the motor immediately to prevent personal injury. Disconnect from the
power source and push and pull the arbor by hand. DO NOT ATTEMPT TO FREE THE CUTTER BY SWITCHING THE MOTOR ON
AND OFF.
9. If the machine is accidentally dropped, always thoroughly examine the machine for signs of damage and check that it functions
correctly before trying to drill a hole.
10. Regularly inspect the machine and check the nuts and screws are tight.
11. Always ensure when using the machine in an inverted position that only the minimum amount of coolant is used and that care
is taken to ensure the coolant does not drip in the motor unit. We advise you to use special cutting paste which is specially
designed for inverted position drilling.
12. ONLY use spare parts advised by your dealer for magnetic drilling machines.
13. Use the magnetic drilling unit on a clean and flat surface only, to prevent the machine breaking out because of poor clamping
force.
14. If you discover any irregularity on machine cables immediately bring the machine to a recognized dealer for a repair or
maintenance service.
4 Manual magnetic drilling machines
2. Technical overview
FE 30 FE 32 FE 32 R/L FE 36 S FE 50 FE 50 R/L FE 100 R/L
Motor
800 W 900 W 1050 W 1080 W 1150 W 1150 W 1800 W
Spindle Direct – 19
mm Weldon
½”x20 NF
– 19 mm
Weldon
½”x20 NF –
19 mm
Weldon
Direct – 19
mm Weldon
MT 2 – 19
mm Weldon
MT 2 – 19 mm
Weldon
MT 3 – 19 mm
Weldon
Hole cutter
30 mm
30 mm 32 mm 32 mm 36 mm 50 mm 50 mm 100 mm
Hole cutter
55 mm
30 mm 32 mm 32 mm N/A 50 mm 50 mm 100 mm
Hole cutter
110 mm
N/A N/A N/A N/A 50 mm 50 mm 100 mm
Countersink
N/A N/A 30 mm N/A N/A 40 mm 55 mm
Reaming
N/A N/A N/A N/A N/A 23 mm 31.75 mm
Twist drills
N/A 13 mm 13 mm N/A 23 mm 23 mm 31.75 mm
Tap
N/A N/A M 16 N/A N/A M 20 M 30
RPM
450 min‐1 450 min‐1 0‐350 min‐1 400 min‐1 I 250 min‐1
II 450 min‐1
I 50‐250 min‐1
II 100‐450 min‐1
I 40‐140 min‐1
II 120‐480 min‐1
Stroke
80 mm 150 mm 150 mm 39 mm 150 mm 150 mm 250 mm
Weight
9.9 kg 12 kg 12 kg 11 kg 13 kg 13 kg 27 kg
Magnet
1500 kg 1500 kg 1500 kg 1200 kg 1700 kg 1700 kg 3500 kg
Check power supply
Make sure the used current corresponds with the machine specifications. When using a cable
extension make sure it can do the job.
5 Manual magnetic drilling machines
3. Operating instructions
4.1 Hole cutter selection
Before starting to drill make sure the cutter of your choice is the right one for the job you want to
do. Following cutters are available in the Fe Powertools program:
6 Manual magnetic drilling machines
4.2 How to mount tools or adapters in a Weldon arbor?
1) Make sure the machine is disconnected from the power supply.
2) Put the center pilot in the cutter hole.
3) Put the cutter or adapter in the arbor, making sure the flat sides are exactly in front of the
arbor retaining screws (picture 1).
4) Tighten the retaining screws.
5) Check if the center pilot can move inside the cutter (up and down).
4.3 Drilling with hole cutters
1 Place the machine at the desired position
TIP: For 100% magnet clamping force you need at least 10 mm of steel. Coatings, paintings and dirt
between magnet and workpiece will affect clamping force.
2 Switch on the magnet
3 Ensure that the magnetic drilling unit is secure on the working piece.
4 Fill the arbor with lubrification/cutting oil in the special meant holes. Always use cutting
oil from your dealer.
5 Set the right RPM by adjusting the gear switch and/or variable speed control. (models FE
32 R/L, FE 50 R/L and FE 100 R/L). The gear switch can be found on the side of the gear
box. Variable speed for FE 32 R/L is placed on the control panel. The variable speed
adjust of FE 50 R/L and FE 100 R/L can be found on the side of the drilling unit.
6 Start the motor by pressing the green motor start button (I).
7 Start bringing the cutter to the workpiece but handle with care and do not apply too
much pressure. The cutter has to find its way in to the material by itself. After 2 mm, the
groove of the cut will help the cutter maintain its place and you can increase the power.

Product specificaties

Merk: Fe Powertools
Categorie: Boormachine
Model: FE 30 kernboormachine

Heb je hulp nodig?

Als je hulp nodig hebt met Fe Powertools FE 30 kernboormachine stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Boormachine Fe Powertools

Fe Powertools

Fe Powertools FE 30 kernboormachine Handleiding

4 Maart 2023
Fe Powertools

Fe Powertools L Handleiding

4 Maart 2023

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita

Makita HR4002 Handleiding

23 November 2024
Bosch

Bosch GBM 13 RE Professional Handleiding

23 November 2024
DeWalt

DeWalt D25003 Handleiding

22 November 2024
Festo

Festo DGSC-6-10-P-P Handleiding

21 November 2024
Cecotec

Cecotec CecoRaptor Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell BAS 18 S-2 Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell Bavaria BSM 1000 Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell BAS 24 S Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell Bavaria BSM 500 Handleiding

19 November 2024
Proviel

Proviel HTM 1305/1 Handleiding

19 November 2024