E-flite EFLG100 Handleiding

E-flite Radiografisch bestuurbaar speelgoed EFLG100

Lees hieronder de 📖 handleiding in het Nederlandse voor E-flite EFLG100 (4 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

10- to 15-Size

Electric Retract

Instructions

Thank you for purchasing the E-ite® 10- to 15-Size

Electric Retracts. These self-contained units are

powered from your model’s receiver and do not require

separate servos.

The retracts are supplied with coil struts installed, plus

adjustable axles, wheel collars, Allen wrenches and a

3-into-1 wire harness (for the tricycle set) or 2-into-1

wire harness (for main gear set). The nose gear unit is

steerable and has a slot in the sliding steering arm to

prevent binding of the steering cable when retracted.

Specications

Current draw

Idle 5mA

Operating 150mA (maximum)

Pulse width trigger points

Down 1.331ms

Up 1.690ms

Operation with FM and DSM

FM 22ms frame rate, 5V signal

DSM 20ms frame rate, 3.3V signal

Sequence time

@ 4.8V 1.25sec

@ 6.0V 1sec

@7.4V 0.8sec

Operating voltage range 4.8 – 7.4V

Aircraft weight: 2.0 - 4.5 lb (0.9 – 2.0 kg)

Unit weight: Nose gear 1.6 oz (45 g)

Main gear 1.3 oz (37 g) each

Parts Available

EFLG101 10 - 15 Main Electric Retract Unit

EFLG102 10 - 15 Left Main Wire Strut

EFLG103 10 - 15 Right Main Wire Strut

EFLG104 10 - 15 Adjustable Axles

EFLRYH9 10 - 15 Dual Plug Y-harness

EFLG111 10 - 15 Nose Electric Retract Unit

EFLG112 10 - 15 Nose Gear Wire Strut

EFLG113 10 - 15 Nose Gear Steering Arm

EFLRYH9TR 10 - 15 Triple Plug Y-harness

Tools Required

Pencil Screwdriver

1.5mm hex wrench 2.5mm hex wrench

Flat le Threadlock

Rotary tool with cutoff wheel

Installation

1. Test t the retract unit in the wing or fuselage to

determine the strut length and axle location. Cut the

strut to length using a cutoff wheel in a rotary tool.

2. Make two at spots on the end of the strut with a le

and use a 2.5mm hex wrench to secure the axle to the

strut. Apply threadlock to the threads of the retaining

screws so they do not loosen from vibration.

EFLG100

EFLG110

3. Install the wheels on the axles. Slide the brass wheel

collar onto the axle and secure it using a 1.5mm hex

wrench. Apply threadlock to the setscrew to prevent it

loosening due to vibration.

4. Mark the retract mounting hole locations on the rails

using a pencil and drill appropriately sized holes for the

hardware you intend to use.

Radio Connections and Operation

1. Plug the connector from each of the retract units into

the 3-into-1 wire harness supplied with the retracts.

2. Plug the single lead from the wire harness into the

gear channel of your receiver. An auxiliary channel can

be used if the gear channel is occupied.

3. Before operating the retracts in the model for the rst

time check that there are no obstructions in the wheel

wells that could impede operation of the gear.

4. Turn on your transmitter and receiver. Use the gear

or other assigned switch to activate the landing gear

and check that it operates correctly.

5. If the switch direction is opposite of that desired, use

the reversing function in the transmitter to change the

retraction direction.

6. If using a 2.4GHz radio, once you have set the

correct servo direction be sure to rebind the system

before ight.

5. Install the retracts in the model using the screws

provided with the kit or those of your own choice. A #4 x

1/2-inch wood screw works well. You will nd the main units

require the use of a 100 degree countersunk woodscrew

while the nose unit requires a button head woodscrew.

Nosegear Steering

Connect the steering pushrod to the steering arm on the

nosegear.

Warranty Information

Warranty Period

Exclusive Warranty- Horizon Hobby, Inc., (Horizon)

warranties that the Products purchased (the “Product”)

will be free from defects in materials and workmanship

for a period of 1 year from the date of purchase by the

Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser

(“Purchaser”) and is not transferable. REPAIR OR

REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE EXCLUSIVE REMEDY OF

THE PURCHASER. This warranty covers only those

Products purchased from an authorized Horizon

dealer. Third party transactions are not covered by this

warranty. Proof of purchase is required for warranty

claims. Further, Horizon reserves the right to change

or modify this warranty without notice and disclaims all

other warranties, express or implied.

(b) Limitations- HORIZON MAKES NO WARRANTY

OR REPRESENTATION, EXPRESS OR IMPLIED,

ABOUT NON-INFRINGEMENT, MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE OF THE

PRODUCT. THE PURCHASER ACKNOWLEDGES

THAT THEY ALONE HAVE DETERMINED THAT

THE PRODUCT WILL SUITABLY MEET THE

REQUIREMENTS OF THE PURCHASER’S INTENDED

USE.

hereunder shall be that Horizon will, at its option, (i)

repair or (ii) replace, any Product determined by Horizon

to be defective. In the event of a defect, these are the

Purchaser’s exclusive remedies. Horizon reserves the

right to inspect any and all equipment involved in a

warranty claim. Repair or replacement decisions are at

the sole discretion of Horizon. This warranty does not

cover cosmetic damage or damage due to acts of God,

accident, misuse, abuse, negligence, commercial use, or

modication of or to any part of the Product. This warranty

does not cover damage due to improper installation,

operation, maintenance, or attempted repair by anyone

other than Horizon. Return of any goods by Purchaser

must be approved in writing by Horizon before shipment.

Damage Limits:

HORIZON SHALL NOT BE LIABLE FOR SPECIAL,

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS

OF PROFITS OR PRODUCTION OR COMMERCIAL

LOSS IN ANY WAY CONNECTED WITH THE

PRODUCT, WHETHER SUCH CLAIM IS BASED IN

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT

LIABILITY. Further, in no event shall the liability of

Horizon exceed the individual price of the Product on

which liability is asserted. As Horizon has no control

over use, setup, nal assembly, modication or misuse,

no liability shall be assumed nor accepted for any

resulting damage or injury. By the act of use, setup or

assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared

to accept the liability associated with the use of

this Product, you are advised to return this Product

immediately in new and unused condition to the place

of purchase.

Law: These Terms are governed by Illinois law (without

regard to conict of law principals).

Safety Precautions:

This is a sophisticated hobby Product and not a toy.

It must be operated with caution and common sense

and requires some basic mechanical ability. Failure to

operate this Product in a safe and responsible manner

could result in injury or damage to the Product or

other property. This Product is not intended for use by

children without direct adult supervision. The Product

manual contains instructions for safety, operation

and maintenance. It is essential to read and follow all

the instructions and warnings in the manual, prior to

assembly, setup or use, in order to operate correctly

and avoid damage or injury.

Questions, Assistance, and Repairs:

Your local hobby store and/or place of purchase

cannot provide warranty support or repair. Once

assembly, setup or use of the Product has been started,

you must contact Horizon directly. This will enable

Horizon to better answer your questions and service

you in the event that you may need any assistance.

For questions or assistance, please direct your

email to productsupport@horizonhobby.com, or call

877.504.0233 toll free to speak to a service technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please

call for a Return Merchandise Authorization (RMA).

Pack the Product securely using a shipping carton.

Please note that original boxes may be included, but

are not designed to withstand the rigors of shipping

without additional protection. Ship via a carrier that

provides tracking and insurance for lost or damaged

parcels, as Horizon is not responsible for merchandise

until it arrives and is accepted at our facility. A Service

Repair Request is available at www.horizonhobby.com

on the “Support” tab. If you do not have internet access,

please include a letter with your complete name, street

address, email address and phone number where

you can be reached during business days, your RMA

number, a list of the included items, method of payment

for any non-warranty expenses and a brief summary of

the problem. Your original sales receipt must also be

included for warranty consideration. Be sure your name,

address, and RMA number are clearly written on the

outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your

original sales receipt verifying the proof-of-purchase

date. Provided warranty conditions have been met,

your Product will be repaired or replaced free of

charge. Repair or replacement decisions are at the sole

discretion of Horizon Hobby.

Non-Warranty Repairs

Should your repair not be covered by warranty the

repair will be completed and payment will be required

without notication or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost.

By submitting the item for repair you are agreeing to

payment of the repair without notication. Repair

estimates are available upon request. You must

include this request with your repair. Non-warranty

repair estimates will be billed a minimum of ½ hour of

labor. In addition you will be billed for return freight.

Please advise us of your preferred method of payment.

Horizon accepts money orders and cashiers checks,

as well as Visa, MasterCard, American Express, and

Discover cards. If you choose to pay by credit card,

please include your credit card number and expiration

date. Any repair left unpaid or unclaimed after 90 days

will be considered abandoned and will be disposed of

accordingly. Please note: non-warranty repair is only

available on electronics and model engines.

Product specificaties

Merk:	E-flite
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	EFLG100

Heb je hulp nodig?

Als je hulp nodig hebt met E-flite EFLG100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Radiografisch bestuurbaar speelgoed E-flite

E-flite Beechcraft D18 1.5m Handleiding

29 Mei 2024

E-flite Opterra 2M Wing PNP Handleiding

9 Juli 2023

E-flite EC-1500 Twin Handleiding

9 Juli 2023

E-flite EFLG100 Handleiding

9 Juli 2023

E-flite UMX Radian BNF Handleiding

8 Juli 2023

E-flite Mystique 2.9m ARF Handleiding

8 Juli 2023

E-flite UMX F4U Corsair Handleiding

8 Juli 2023

E-flite T-28 1.2m BNF Basic Handleiding

7 Juli 2023

E-flite UMX Habu 180 DF BNF Handleiding

7 Juli 2023

E-flite UMX Spacewalker Handleiding

7 Juli 2023

Handleiding Radiografisch bestuurbaar speelgoed

Nieuwste handleidingen voor Radiografisch bestuurbaar speelgoed

Spektrum DX5 Pro Handleiding

16 November 2024

Hobbywing XeRun XR10 PRO DR Handleiding

6 November 2024

Hobbywing XeRun XR10 Pro G3 Handleiding

5 November 2024

Amewi Hyper Go Handleiding

30 September 2024

Carson Drift Burner Handleiding

30 September 2024

Carson Micro X-Warrior 2.0 Handleiding

30 September 2024

Carson Toxic Spider 340 Handleiding

30 September 2024

Hobbywing XeRun XR10 Pro WP Handleiding

24 September 2024

Hobbywing XeRun XR10 Stock Spec G2 Handleiding

24 September 2024

Hobbywing XeRun XR10 Justock G3S Handleiding

24 September 2024